• 한국세라믹학회지
• /
• 제36권5호
• /
• pp.539-546
• /
• 1999

Absorbent polymer-cement composites were fabricated by the semi-powder mixing OPC(ordinary Portland cement) with an absorbent polymer. The effects of absorbent polymer on the mechanical properties and the hydration characteristics were observed and the polymer-cement interaction also discussed. Absorbent polymer-cement composites showed the value of total porosity of 8vol% the value of 28 days flexural strength was up to 280 Kgf/cm2 in the case of absorbent polymer-cement composite at 1 wt% absorbent polymer content and microstructure of absorbent polymer-cement composite has been observed more dense than that of OPC paste. Accordingly the permeability of compositewas improved and so the moisture resistance was also increased. Adding polymer did not retard the hydration of OPC. It was considered from the results of IR(infrared) analysis that the functional group of absorbent polymer would be changed from unidentate to bidentate during by the hydration of cement minerals.

• Mycobiology
• /
• 제42권1호
• /
• pp.59-65
• /
• 2014

Entomopathogenic fungi are promising pest-control agents but their industrial applicability is limited by their thermosusceptibility. With an aim to increase the thermotolerance of Isaria fumosorosea SFP-198, moisture absorbents were added to dried conidial powder, and the relationship between its water potential and thermotolerance was investigated. Mycotized rice grains were dried at $10^{\circ}C$, $20^{\circ}C$, $30^{\circ}C$, and $40^{\circ}C$ and the drying effect of each temperature for 24, 48, 96, and 140 hr was determined. Drying for 48 hr at $10^{\circ}C$ and $20^{\circ}C$ reduced the moisture content to < 5% without any significant loss of conidial thermotolerance, but drying at $30^{\circ}C$ and $40^{\circ}C$ reduced both moisture content and conidial thermotolerance. To maintain thermotolerance during storage, moisture absorbents, such as calcium chloride, silica gel, magnesium sulfate, white carbon, and sodium sulfate were individually added to previously dried-conidial powder at 10% (w/w). These mixtures was then stored at room temperature for 30 days and subjected to $50^{\circ}C$ for 2 hr. The white carbon mixture had the highest conidial thermotolerance, followed by silica gel, magnesium sulfate, and then the other absorbents. A significant correlation between the water potential and conidial thermotolerance was observed in all conidia-absorbent mixtures tested in this study (r = -0.945). Conidial thermotolerance in wet conditions was evaluated by adding moisturized white carbon (0~20% $H_2O$) to conidia to mimic wet conditions. Notably, the conidia still maintained their thermotolerance under these conditions. Thus, it is evident that conidial thermotolerance can be maintained by drying mycotized rice grains at low temperatures and adding a moisture absorbent, such as white carbon.

• 한국가금학회지
• /
• 제50권3호
• /
• pp.125-132
• /
• 2023

본 연구는 깔짚 관리를 위한 수분흡수제의 도포 시기가 육계 생산성, 혈액성상, 깔짚 수분함량 및 발바닥피부염 발생 양상에 미치는 영향을 조사하기 위하여 수행되었다. 공시동물은 1일령 Ross 308 육계(42.0±0.24 g) 680수를 이용하여 평사(칸당 2 m²)에서 5주 동안 사육하였다. 처리구는 무처리 대조구(NC), 3주령 깔짚 처리구(PC), 수분흡수제 0주령, 0과 3주령, 3주령 도포의 총 5처리구, 처리당 4반복, 반복당 34수씩 680수를 완전임의 배치하였다. 육계 계사 내 깔짚 및 수분흡수제 도포 시기에 따른 체중, 증체량, 사료섭취량 및 사료요구율은 처리구 사이에서 유의적인 차이가 나타나지 않았다. 육계 계사 내 깔짚 및 수분흡수제 도포 시기에 따른 혈액 내 혈구 조성(leukocyte, erythrocyte, platelets) 및 H/L 비율은 유의차가 나타나지 않았다. 깔짚 수분함량 및 FPD 점수는 5주령에 깔짚 및 수분흡수제 처리구에서 유의적으로 감소하였다(P<0.05). 본 연구에 사용된 육계의FPD 점수는 NC 처리구에 비해 PC 처리구에서 가장 낮았으며(P<0.05), W1 및 W2 처리구보다 W3 처리구에서 낮은 경향을 보였다. 발바닥피부염은 PC와 W3 처리구에서 다른 처리구에 비해 낮은 비율을 보였으며, NC 처리구에서 발바닥피부염 발생 비율이 가장 높게 나타났다. 경제성을 분석한 결과, PC 처리구에서 지출이 가장 많이 발생하였으며, W3 처리구에서 지출이 가장 낮게 나타났다. W3 처리구에서 수입이 가장 높았으며, NC 처리구의 수입이 가장 낮았다. 총수입에서 총지출을 제한 이익은 185,859원(1,367 원/수)으로W3 처리구에서 가장 많았다. 결론적으로, 육계 깔짚에 수분흡수제를 3주령에 도포하였을 때, 깔짚 수분함량과 FPD 개선효과가 나타났다.

• Journal of the Korean Wood Science and Technology
• /
• 제18권2호
• /
• pp.36-48
• /
• 1990

This experiment was carried out to improve the quality of high absorbent polymer which has excellent absorptivity and water retention compared to pulp and absorption sheet, through absorption characteristics-absorptive power, water retention, absorption rate, gel strength, pH, particle size, and moisture content. - of six polymers, namely, anionic polyacrylamide, cationic polyacrylamide, polyacrylic, acid polyvinyle alcohol 500, and 1500, and a-cellulose. and to examine the possibility of substitution of amide groups for carboxyl group and/or hydroxyl group which were commercial high absorbent polymer by comparing the absorption characteristics of the polymers. Polyacrylamide has high absorptive power and water retention, but has low gel strength and poor absorption rate. The rest of polymers were similiar to ${\alpha}$-cellulose in every respect. Thus, polyacrylamides could be replaced with polyacrylic acid and polyvinyl alcohol which are presently a high absorbent polymers. In comparing the absorption characteristics and the absorptive power of the polymers-anionic polyacrylamide, cationic polyacrylamide, polyacrylic acid, polyvinyle alcohol. a-cellulose-the absorptive power was in inverse proportion to the gel strength and absorption rates, affected by the particle size and pH change.

• Asian-Australasian Journal of Animal Sciences
• /
• 제25권4호
• /
• pp.471-478
• /
• 2012

The role of moisture absorptive capacity of pre-silage material and its relationship with silage effluent in high moisture by-product feedstuffs (HMBF) is assessed. The term water retention capacity which is sometimes used in explaining the rate of effluent control in ensilage may be inadequate, since it accounts exclusively for the capacity of an absorbent incorporated into a pre-silage material prior to ensiling, without consideration to how much the pre-silage material can release. A new terminology, 'potential water retention capacity' (PWRC), which attempts to address this shortcoming, is proposed. Data were pooled from a series of experiments conducted separately over a period of five years using laboratory silos with four categories of agro by-products (n = 27) with differing moisture contents (highest 96.9%, lowest 78.1% in fresh matter, respectively), and their silages (n = 81). These were from a vegetable source (Daikon, Raphanus sativus), a root tuber source (potato pulp), a fruit source (apple pomace) and a cereal source (brewer's grain), respectively. The pre-silage materials were adjusted with dry in-silo absorbents consisting wheat straw, wheat or rice bran, beet pulp and bean stalks. The pooled mean for the moisture contents of all pre-silage materials was 78.3% (${\pm}10.3$). Silage effluent decreased (p<0.01), with increase in PWRC of pre-silage material. The theoretical moisture content and PWRC of pre-silage material necessary to stem effluent flow completely in HMBF silage was 69.1% and 82.9 g/100 g in fresh matter, respectively. The high correlation (r = 0.76) between PWRC of ensiled material and silage effluent indicated that the latter is an important factor in silage-effluent relationship.

• 한국의류산업학회지
• /
• 제1권2호
• /
• pp.160-165
• /
• 1999

The thermal properies of the pure linen fabrics available in the market and linen blended woven fabrics were measured at the moisture content of 0%, 20%, 40% and 60% using KES-F7 system (Thermo Iabo II type). The experimental properties were statistically analyzed by the rate of water absorbent. The main results were as follows; There is a positive correlation between the thermal insulation value (TIV) and thickness of pure linen fabrics and linen blended woven fabrics by water absorption. Whereas an negative correlation exists between the TIV and cover factor. There is a high positive correlation among the thermal conductivity (k), thickness and weight of pure linen fabrics and linen blended woven fabrics by water absorption. Wherase a high negative correlation exist between the k and air' permeability (Ap). There is a high positive correlation between the feeling of warmth/coldness and bulk density of pure linen and linen blended woven fabrics by water absorption. Wherase a high negative correlation exists between the feeling of warmth/coldness and porosity. There is a negative correlation between TIV and $q_{max}$ of pure linen fabrics and linen blended woven fabrics. The higher the rate of water absorbent, the lower the TIV. This means that TIV decreases by water absorption. As for the thermal property by rate of water absorbent $q_{max}$ and k increase by water absorption and reach max-value at 60% rate of water absorbent. The TIV decreases by water absorption and has +value at 0% rate of water absorbent, whereas it has -value with a feeling of coldness at 20%, 40%. and 60% rate of water absorbent.

• E2M - 전기 전자와 첨단 소재
• /
• 제1권1호
• /
• pp.70-77
• /
• 1988

This paper describes the influence of the electrode materials, moisture content, electrolyte density, temperature, surface state, ion absorbent on the C.T.I of phenolic resin by the I.E,C, 112 method. C.T.I are increased for electrode materials with low hydrogen overvoltage and high soluble point. Increusing moisture content of samples increased by logarithmical on the droplet number to tracking breakdown. Increasing electrolyte temperature region above 70-80(.deg.C) decreased hydrogen over-voltage, following the density changes are decreased by C.T.I=1/aD$^{2}$-bD+C.

• 패션비즈니스
• /
• 제15권6호
• /
• pp.40-55
• /
• 2011

The purpose of this research is to review testing principle, testing design and experimental results of the four dynamic moisture movement testers. The research analyzes Moisture Manager Tester (MMT), Alambeta Instrument, Dynamic Surface Moisture Movement Tester, and Gravimetric Absorbent Testing Method based on American Society for Testing and Material (ASTM) E 96 which is an international standard testing method. Although many of researches use ASTM E 96 to measure moisture movement on a fabric, it has several weaknesses, such as long experimental time and a physical change of sample by a holder of the frame. Hence, lots of researchers have studied and developed the new measurement systems measuring moisture management on a fabric or garment and ultimately mimic heat energy and perspiration created by the human body. These moisture management systems use a variety of parameters, such as electricity, color, and sensor to measure their movement in the fabric. Through comparison with the existing tester (ASTM E 96), the research recognizes the strength and weakness in the dynamic moisture movement testers.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.209-209
• /
• 2006

Ultra-fine fibers are spun by expensive fiber spinning technology using special spinnerets. Ultra-fine fibrous materials have attracted considerable attentions because of their potential applications as high performance wiping cloths, water absorbent sound proofing materials and moisture transfer sporting good. However, production expense of ultra-fine fibers is 5 to 7 times higher than general textile materials. The objective of this research is to develop cost-effective recycling process to produce multi-functional ultra-fine fibrous material in terms of the development of garnetting and carding machines for ultra-fine fibrous material waste and scrap. The efficiency of sound absorption for the recycled polyester nonwoven increased with decreasing length and thickness of component fibers, which was attributed to the reduction of air permeability. It is expected that high value and cost-effective textile products are developed using ultra-fine fibrous wastes and that sound proofing material and oil absorbent f

• 한국전기전자재료학회논문지
• /
• 제37권4호
• /
• pp.347-357
• /
• 2024

Oxide semiconductor gas sensors are widely used for detecting toxic, explosive, and flammable gases due to their simple structure, cost-effectiveness, and potential integration into compact devices. However, their reliable gas detection is hindered by a longstanding issue known as humidity dependence, wherein the sensor resistance and gas response change significantly in the presence of moisture. This problem has persisted since the inception of oxide semiconductor gas sensors in the 1960s. This paper explores the root causes of humidity dependence in oxide semiconductor gas sensors and presents strategies to address this challenge. Mitigation strategies include functionalizing the gas-sensing material with noble metal/transition metal oxides and rare-earth/rare-earth oxides, as well as implementing a moisture barrier layer to prevent moisture diffusion into the gas-sensing film. Developing oxide semiconductor gas sensors immune to humidity dependence is expected to yield substantial socioeconomic benefits by enabling medical diagnosis, food quality assessment, environmental monitoring, and sensor network establishment.