• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.4A
• /
• pp.414-422
• /
• 2011

This paper describes a design of low-density parity-check(LDPC) decoder supporting block length 2,304-bit and code rate 1/2 of IEEE 802.16e mobile WiMAX standard. The designed LDPC decoder employs the min-sum algorithm and partially parallel layered-decoding architecture which processes a sub-matrix of $96{\times}96$ in parallel. By exploiting the properties of the min-sum algorithm, a new memory reduction technique is proposed, which reduces check node memory by 46% compared to conventional method. Functional verification results show that it has average bit-error-rate(BER) of $4.34{\times}10^{-5}$ for AWGN channel with Fb/No=2.1dB. Our LDPC decoder synthesized with a $0.18{\mu}m$ CMOS cell library has 174,181 gates and 52,992 bits memory, and the estimated throughput is about 417 Mbps at 100-MHz@l.8-V.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3425-3430
• /
• 2013

The fast-growing market in wireless communications has led to the development of multi-standard mobile terminals. In this paper, a frequency-tunable active RC bandpass filter for multi-standards wireless communication system is designed using an active inductor. The conventional bandpass filter design methods employ the high order filter or high quality factor Q to improve the stopband attenuation characteristics and frequency selectivity of the passband. The proposed bandpass filter based on the high Q active inductor has an improved frequency characteristics. The center frequency and gain of the designed bandpass filter is tuned by employing the tuning circuit. We have performed the simulation using TSMC $0.18{\mu}m$ process parameter to analyze the characteristics of the designed active RC bandpass filter. The bandpass filter with Q=20.5 has 90MHz half power bandwidth at the center frequency of 1.86GHz. Moreover, the center frequency of the proposed bandpass filter can be tuned between 1.86~2.38GHz for the multi-standards wireless communication system using the capacitor of the tuning circuit.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.161-167
• /
• 2008

This paper describes the overview of spectrum requirement estimation recommended in ITU-R Rec. M.1390 and [IMT.METH] and its difference for the IMT mobile service, and a (IMT.METH) methodology is applied to the spectrum estimation of the recent IMT service. The traffic model and traffic calculation algorithm is briefly described for the carried traffic which is determined in terms of the offered traffic, system rapacity, and the criteria of quality of service. And the spectrum requirement demand which is required from year 2010 to year 2015 is calculated as an example for the IMT service which is recently operated and deployed in the current Korean market after obtaining the reasonable market data and the ITU market prediction data.

• Journal of Digital Convergence
• /
• v.14 no.7
• /
• pp.21-27
• /
• 2016

Big Data is gathering all the attention from every business community. Pervasive use of machine-to-machine (M2M) applications and mobile devices bring an explosion of data. By analyzing this data, the private and public sectors can benefit in the areas of cost reduction and productivity. The Korean government is actively pursuing Big Data initiatives to promote its usage. This paper aims to select industries which fit for the development of Big Data with a verification of the experts. The analytic hierarchy process (AHP) is applied to systematically derive the opinion of more than 50 professionals. Medical / welfare, transportation / warehousing, information and communications / information security, energy, the financial sector have been identified as promising industries. The results can be utilized in developing Big Data best practices thus contributing industrial development.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.12
• /
• pp.2249-2260
• /
• 2017

IMO (International Maritime Organization) has been providing GMDSS (Global Maritime Distress and Safety System) and mandating to install distress and safety systems according to SOLAS. Digital-HF(High-Frequency) coast station communication system maintains interoperability between ship and coast station and digital data exchange in maritime mobile service by digitizing existing analog base voice communication. In this paper, we analyze ITU-R M. 1798-1 established by ITU for digital HF communications and propose Advanced annex2 and new Annex 5 to improve the problems of the existing Annex 2 and Annex 4. The proposed OFDM protocol basically adopts ARQ (Automatic Retransmission Request) which retransmits when an error occurs in a half-duplex manner between an information transmitting side (ISS) and an information receiving side (IRS) and we propose a digital HF communication system and its operational concept which is more reliable and superior than the existing ITU-R M. 1798 by implementing technical development on implementation and performance improvement.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.517-531
• /
• 1999

This paper presents the development of the 2-mode variable gain high power amplifier for a transmitter of INMARSAT-M operating at L-band(1626.5-1646.5 MHz). This SSPA(Solid State Power Amplifier) is amplified 42 dBm in high power mode and 36 dBm in low power mode for INMARSAT-M. The allowable error sets +1 dBm of an upper limit and -2 dBm of a lower limit, respectively. To simplify the fabrication process, the whole system is designed by two parts composed of a driving amplifier and a high power amplifier, The HP's MGA-64135 and Motorola's MRF-6401 are used for driving amplifier, and the ERICSSON's PTE-10114 and PTF-10021 are used the high power amplifier. The SSPA was fabricated by the circuits of RF, temperature compensation and 2-mode gain control circuit in aluminum housing. The gain control method was proposed by controlling the voltage for the 2-mode. In addition, It has been experimentally verified that the gain is controlled for single tone signal as well as two tone signals. The realized SSPA has 42 dB and 36 dB for small signal gain within 20 MHz bandwidth, and the VSWR of input and output port is less than 1.5:1 The minimum value of the 1 dB compression point gets 5 dBm for 2-mode variable gain high power amplifier. A typical two tone intermodulation point has 32.5 dBc maximum which is single carrier backed off 3 dB from 1 dB compression point. The maximum output power of 43 dBm was achieved at the 1636.5 MHz. These results reveal a high power of 20 Watt, which was the design target.the design target.

• Journal of IKEEE
• /
• v.2 no.1 s.2
• /
• pp.1-14
• /
• 1998

In this paper, Antenna, LNA, Mixer, VCO, and Modulation/Demodulation in Baseband processor which are the RF main components in Wireless LAN system for ultra high-speed communications network are studied. Antenna bandwidth and selective fading due to multipath can be major obstacles in high speed digital communications. To solve this problem, wide band MSA which has loop-structure magnetic antenna characteristics is designed. Distributed mixer using dual-gate GaAs MESFET can achieve over 10dB LO/RF isolation without hybrid, and minimize circuit size. As linear mixing signal is produced, distortions can be decreased at baseband signals. Conversion gain is achieved by mixing and amplification simultaneously. Mixer is designed to have wide band characteristics using distributed amplifier. In VCO design, Oscillator design method by large signal analysis is used to produce stable signal. Modulation/Demodulation system in baseband processor, DS/SS technique which is robust against noise and interference is used to eliminate the effect of multipath propagation. DQPSK modulation technique with M-sequences for wideband PN spreading signals is adopted because of BER characteristic and high speed digital signal transmission.

• Journal of Communications and Networks
• /
• v.18 no.5
• /
• pp.837-845
• /
• 2016

Providing a customer with tailored location-based services (LBSs) is a fundamental problem. For location-estimation techniques with radio-based measurements, LBS applications are widely available for mobile devices (MDs), such as smartphones, enabling users to run multi-task applications. LBS information not only enables obtaining the current location of an MD but also provides real-time push-pull communication service. For indoor environments, localization technologies based on radio frequency (RF) pattern-matching approaches are accurate and commonly used. However, to survey radio information for pattern-matching approaches, a considerable amount of time and work is spent in indoor environments. Consequently, in order to reduce the system-deployment cost and computing complexity, this article proposes an indoor positioning approach, which involves using Asus Xtion to facilitate capturing RF signals during an offline site survey. The depth information obtained using Asus Xtion is utilized to estimate the locations and predict the received signal strength (RF information) at uncertain locations. The proposed approach effectively reduces not only the time and work costs but also the computing complexity involved in determining the orientation and RF during the online positioning phase by estimating the user's location by using a smartphone. The experimental results demonstrated that more than 78% of time was saved, and the number of samples acquired using the proposed method during the offline phase was twice as much as that acquired using the conventional method. For the online phase, the location estimates have error distances of less than 2.67 m. Therefore, the proposed approach is beneficial for use in various LBS applications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.12
• /
• pp.2674-2685
• /
• 1997

In this paper, the design and imprlementation of dual-band power amplifier which is used as a critical part for mobile phone to be simultaneously working at a dual band, 800MHz CDAM and PCS frequency band is described. DC operating point of power FET is limited to Class-B to enable long talk time considering that the tyupical power range of CDMA phones in working is around 10 to Class-B to enable long talk time considering that the typical power range of CDMA phones in working is around 10 to 15dBm, i.e., liner range. The power amplifier which employs two GaAs FETs with good linerity at a low operating point has duplexer cuplexer circuit to separate two frequency bands at input and output stage. Electromagnetic analysis for via holes and coupling between narrow transmission lines is included to design a circuit. Moduld size of 0.96CC($22{\times}14.5{\times}3mm^3$) and maximum module current of 130mA at output power range, 10 to 15dBm are attained. The power amplifer module has achieved ACPR performance with 2 to 3dB marging from IS-95 requirement at output powers, 23.5dBm for PCS and 28dBm for 800MHz CDMA respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.670-680
• /
• 2010

A low power single-chip CMOS receiver for 60 GHz mobile application are proposed in this paper. The single-chip receiver consists of a 4-stage current re-use LNA with under 4 dB NF, Cgs compensating resistive mixer with -9.4 dB conversion gain, Ka-band low phase noise VCO with -113 dBc/Hz phase noise at 1 MHz offset from 26.89 GHz, high-suppression frequency doubler with -0.45 dB conversion gain, and 2-stage current re-use drive amplifier. The size of the fabricated receiver using a standard 0.13 ${\mu}m$ CMOS technology is 2.67 mm$\times$0.75 mm including probing pads. An RF bandwidth is 6.2 GHz, from 55 to 61.2 GHz and an LO tuning range is 7.14 GHz, from 48.45 GHz to 55.59 GHz. The If bandwidth is 5.25 GHz(4.75~10 GHz) The conversion gain and input P1 dB are -9.5 dB and -12.5 dBm, respectively, at RF frequency of 59 GHz. The proposed single-chip receiver describes very good noise performances and linearity with very low DC power consumption of only 21.9 mW.