• Journal of the Korea Society of Computer and Information
• /
• v.22 no.4
• /
• pp.67-74
• /
• 2017

The objective of this paper is to design broadband microstrip patch antenna for mobile communication service. The enhanced features were confirmed and proved by comparing the proposed antenna with the antennae that have been reported in the relevant literatures. The experimental results show that the impedance bandwidth(VSWR ${\leq}2$) of 19.6%(fo=1,920MHz) and the peak gain of 5.53dBi(at 1,900MHz) were obtained by the mobile communication service frequency band. The proposed antenna had the impedance bandwidth of about 3.1% larger than that of the reported microstrip antenna.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.225-230
• /
• 2005

The proposed Triple-band Compact Chip Antenna using Coupled Meander line and stacked meander Structure for Mobile RFID/PCS/WiBro. The proposed antenna is designed to operate at 900, 1800, and 2350 MHz, and is realized by parasitic coupled and stacked a meander line. Meander lines are using extend length of effective current path more than monopole and contribute miniaturization. The coupled meander line controls the excitations of the Mobile RFID and PCS, stacked meander line controls the excitation of the WiBro. The proposed antenna size is $11mm\times22.5mm\times1mm$. The antenna supports 900MHz, 1800MHz and 2350MHz operations simultaneously with bandwidths of 33MHz, 230MHz and 100MHz, respectively. The proposed antenna gains are result of simulation to be -0.8dBi, 3dBi and 3.8dBi, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.2
• /
• pp.149-155
• /
• 2014

In this paper, we study the complex mobile antenna for WPT(Wireless Power Transfer) with NFC(Near Field Communication) of inductive coupling using FPCB which has half thickness compared with the existing coil type antennas. Considering the pattern thickness of loop antenna, the analysis of electromagnetic wave absorber and battery's influence, absorber thickness, the ranges of design parameters are obtained. The proposed antenna has 0.45 mm thickness using single layer 3 oz FPCB and absorber. From measurement, the characteristics of NFC antenna can be satisfied with the specifications of EMVCo. and domestic mobile telecommunication and the transmission efficiency of the proposed WPT antenna is 68.1 % which is competitive with the existing coil type antenna. From the results of this paper, it has been confirmed that the proposed antenna can be used as the WPT and NFC antenna for mobile phone. Key words: Wireless Power Transfer, Near Field Communication, Mobile Phone Antenna, Absorber, FPCB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.713-718
• /
• 2006

We designed and fabricated, in this paper, a quintuple band folded monopole antenna for the mobile phone handset that can be provided multiple mobile services. Antenna design was based on the compensation of series antenna capacitance with the expansion of physical antenna length by the proper folding structure. It's shown that this antenna satisfies quintuple service band as CDMA/GSM/DCS/USPCS/WCDMA, and is more cost competitive than conventional metal plate pressing method by applying on flexible PCB technology. Measured maximum gain on quintuple band were $-2.51{\sim}+1.82 dBi$, and radiation patterns were also shown nearly omnidirectional on all bands.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.7
• /
• pp.737-743
• /
• 2011

In this paper, we designed and implemented a Monopole+IFA(Inverted F Antenna) hybrid antenna using the coupled feeding structure for the all band mobile phone. Studied antenna has wide band characteristics by the simultaneous operation both monopole and IFA under the coupled feeding structure. An antenna has designed PCB embedded type without antenna carrier component for the low in cost. Implemented antenna has within 2.5:1 for VSWR under LTE/CDMA/GSM900/DCS/USPCS/WCDMA/WiBro/WiFi in all band for the mobile services Measured average gains and efficiencies were -3.98~-0.09 dBi and 40.03~97.99 % for the LTE, CDMA, GSM900 band, and -3.90~-1.01 dBi and 40.70~79.31 % for the DCS, USPCS, WCDMA, WiBro, WiFi band. It's shown that studied antenna can be applied to all band mobile phone antenna including LTE.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.4
• /
• pp.71-75
• /
• 2008

A folded monopole antenna is proposed for mobile communication applications. The proposed antenna covers CDMA and GSM at low frequency band, and it has a wide bandwidth (6.85 GHz) at high frequency band to cover GPS, DCS, USPCS, UHfS, WLAN (2.4, 5.2, 5.8 GHz), and the future application of IEEE 802.16e mobile WiMAX.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.2
• /
• pp.161-166
• /
• 2009

In this paper, we propose the internal mobile antenna for TDMB and KPCS. The proposed antenna is made of different dielectric substrate and it has small size ($45{\times}8{\times}8\;mm$, about 2.8 cc) for mobile device. TDMB antenna is designed spiral structure that makes maximum current for each cell and KPCS antenna is PIFA that is usually used for internal antenna. In order to compensate length of resonance TDMB antenna has a large inductor above 100 nH. In this case, the inductor isolate KPCS signal at TDMB by cutting high frequency. Also the antenna has good isolation because TDMB radiator is parasitic element in KPCS band. We simulated the antenna by using CST microwave studio and measured performance of the antenna in anechoic chamber Proposed antenna has $-6{\sim}-14\;dBi$ gain for TDMB and $-3.5{\sim}-5\;dBi$ gain for KPCS.

• Journal of IKEEE
• /
• v.19 no.2
• /
• pp.124-132
• /
• 2015

In this paper, we proposed a multiband internal antenna for LTE mobile handset that could be used for mobile devices. The proposed antenna has a volume of $50mm(W){\times}21mm(L){\times}5mm(H)$, ground plane size is $60mm(W){\times}100mm(L)$, and covers 9 service frequency bands including LTE(Long Term Evolution) band with VSWR(Vlotage Standing Wave Ratio) less than 3. With rapid change of technologies, people wants to include more function into one device. In addition, each country uses different frequency band for traffic service, it is necessary to design multiband antenna for mobile phone since traveling foreign country needs roaming. And if we can cover several services with one antenna, cost and volume needed for antennas are minimized. A HFSS (High Frequency Structure Simulator) of the Ansoft Corporation based on a finite element method is employed to analyze the proposed antenna in the design process and to compare the simulation and experimental results.

• ETRI Journal
• /
• v.26 no.6
• /
• pp.605-614
• /
• 2004

In this paper, we investigate array calibration algorithms to derive a further improved version for correcting antenna array errors and RF transceiver errors in CDMA smart antenna systems. The structure of a multi-channel RF transceiver with a digital calibration apparatus and its calibration techniques are presented, where we propose a new RF receiver calibration scheme to minimize interference of the calibration signal on the user signals. The calibration signal is injected into a multi-channel receiver through a calibration signal injector whose array response vector is controlled in order to have a low correlation with the antenna response vector of the receive signals. We suggest a model-based antenna array calibration to remove the antenna array errors including mutual coupling errors or to predict the element patterns from the array manifold measured at a small number of angles. Computer simulations and experiment results are shown to verify the calibration algorithms.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.28-31
• /
• 2004

This paper describe analysis active microstrip antenna with low noise amplifier at 900 MHz for mobile communication. The microstrip patch antenna is integrated with low noise amplifier on a permittivity 4.5 (Epoxy-FR4) and thickness of substrate 1.6 mm. Low noise amplifier is designed by using GaAs FETs. The analysis characteristics of antenna include return loss, input impedance, vswr, radiation pattarn, bandwidth and gain of antenna. Mesurement gain of antenna is shown 19.2435 dBi.