• 한국자기학회지
• /
• 제9권5호
• /
• pp.256-262
• /
• 1999

DC/RF magnetron sputtering system을 이용하여 CoCr 박막 및 CoCrMo 박막의 Si 하지층의 도입에 따른 자기적 특성 및 미세구조의 변화에 대해 살펴보았다. 박막의 자기적 특성을 VSM을 통하여 측정한 결과, 고온에서 증착된 CoCrMo/Si 박막의 경우가 CoCr/Si 박막과는 달리 Si 하지층의 두께가 증가할수록 수직보자력값이 증가하는 것을 알 수 있었으며 AFM과 SEM을 이용한 surface morphology의 변화를 통하여 결정립 미세화와 균일화가 수직보자력을 증진시킴을 알 수 있었다. 또한, 박막의 결정배향성 및 미세구조를 XRD와 SEM을 통하여 관찰한 결과, CoCrMo/Si 박막의 (0002)우선 배향성이 CoCr/Si 박막의 (0002) 우선 배향성보다 상당히 크게 증진된 것을 볼 수 있었으며, SEM의 단면 측정을 통하여 CoCrMo/Si 박막과 CoCr/Si 박막의 기판 표면에서 성장하는 columnar 구조의 발달을 잘 관찰할 수 있었다.

• 한국표면공학회지
• /
• 제40권6호
• /
• pp.279-282
• /
• 2007

Cr-Mo-Si-C-N coatings were deposited on steel and Si wafer by a hybrid system of AIP and sputtering techniques using Cr, Mo and Si target in $Ar/N_2/CH_4$ gaseous mixture. Instrumental analyses of XRD and XPS revealed that the Cr-Mo-Si-C-N coatings must be a composite consisting of fine(Cr, Mo and Si)(C and N) crystallites and amorphous $Si_3N_4$ and SiC. The hardness value of Cr-Mo-Si-C-N coatings significantly increased from 41 GPa of Cr-Mo-C-N coatings to about 53 GPa with Si content of 9.3 at.% due to the refinement of (Cr, Mo and Si)(C and N) crystallites and the composite microstructure characteristics. A systematic investigation of the microstructures and mechanical properties of Cr-Mo-Si-C-N coatings prepared with various Si contents is reported in this paper.

• 한국표면공학회지
• /
• 제39권3호
• /
• pp.110-114
• /
• 2006

In this work, comparative studies on microstructure and mechanical properties between $Mo_2N$ and Mo-Si-N coatings were conducted. Ternary Mo-Si-N coatings were deposited on AISI D2 steel substrates by a hybrid method, where AIP technique was combined with a magnetron sputtering technique. Instrumental analyses of XRD, HRTEM, and XPS revealed that the Mo-Si-N coatings must be a composite consisting of fine $Mo_2N$ crystallites and amorphous $Si_3N_4$. The hardness value of Mo-Si-N coatings significantly increased from 22 GPa of $Mo_2N$ coatings to about 37 GPa with Si content of 10 at.% due to the refinement of $Mo_2N$ crystallites and the composite microstructure characteristics. The average friction coefficient of the Mo-Si-N coatings gradually decreased from 0.65 to 0.4 with increasing Si content up to 15 at.%. The effects of Si content on microstructure and mechanical properties of Mo-N coatings were systematically investigated.

• 한국진공학회지
• /
• 제2권4호
• /
• pp.507-514
• /
• 1993

The solid state reaction of Mo/Si multilayer thin films produced by RF magnetron sputtering technique was examine dusing differential scanning calorimetry (DSC) and x-ray diffraction, and explained in view of two concepts, effective drivig force and effective heat of formation. In constant scanning rate DSC, there were two exothermic peks which corresponded to the formation of h-MoSi2 and t-MoSi2 , respectively. The activation energyfor theformation of h-MoSi2 was 1.5eV , and that of t-MoSi2 was 7.8eV. Nucleation wa stherate controlling mechanism for each of the silicide formation. Amorphous phase was not formed , which was consistent withtheprediction by the concept of effective driving force. h-MoSi2 the first crystalline phase, was considered to have lower interfacial free energy than t-MoSi2 and by increasing temperature it was transformed into more stable t-MoSi2.

• 한국해양공학회지
• /
• 제16권6호
• /
• pp.60-64
• /
• 2002

This paper describes the machining characteristics of the MoSi$_2$--based composites through the process of electric discharge drilling with various tubular electrodes. In addition to hardness characteristics, microstructures of Nb/MoSi$_2$laminate composites were evaluated from the variation of fabricating conditions, such as preparation temperature, applied pressure, and pressure holding time. MoSi$_2$-based composites have been developed in new materials for jet engines of supersonic-speed airplanes and gas turbines for high-temperature generators. These high performance engines may require new hard materials with high strength and high temperature-resistance. Also, with the exception of grinding, traditional machining methods are not applicable to these new materials. Electric discharge machining (EDM) is a thermal process that utilizes a spark discharge to melt a conductive material. The tool electrode is almost -unloaded, because there is n direct contact between the tool electrode and the work piece. By combining a non-conducting ceramic with more conducting ceramic, it was possible to raise the electrical conductivity. From experimental results, it was found that the lamination from Nb sheet and MoSi$_2$ powder was an excellent strategy to improve hardness characteristics of monolithic MoSi$_2$. However, interfacial reaction products, like (Nb, Mo)SiO$_2$and Nb$_2$Si$_3$formed at the interface of Nb/MoSi$_2$, and increased with fabricating temperature. MoSi$_2$composites, with which a hole drilling was not possible through the conventional machining process, enhanced the capacity of ED-drilling by adding MbSi$_2$, relative to that of SiC or ZrO$_2$reinforcements.

• 한국표면공학회지
• /
• 제29권6호
• /
• pp.683-690
• /
• 1996

In this study, the diffusion barrier properties of $1000 \AA$ thick molybdenum compounds (Mo, Mo-N, $MoSi_2$, Mo-Si-N) were investigated using sheet resistance measurements, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Scanning electron microscopy (SEM), and Rutherford backscattering spectrometry (RBS). Each barrier material was deposited by the dc magnetron sputtering, and annealed at 300-$800^{\circ}C$ for 30min in vacuum. Mo and $MoSi_2$ barrier were failed at low temperature due to Cu diffusion through grain bound-aries and defects of Mo thin film and the reaction of Cu with Si within $MoSi_2$ respectively. A failure temperature could be raised to $650^{\circ}C$-30min in the Mo barrier system and to $700^{\circ}C$-30min in the Mo-silicide system by replacing Mo and $MoSi_2$ with Mo-N and Mo-Si-N, respectively. The crystallization temperature in the Mo-silicide film was raised by the addition of $N_2$. It is considered that not only the N, stuffing effect but also the variation of crystallization temperature affects the reaction of Cu with Si within Mo-silicide. It was found that Mo-Si-N is more effective barrier than Mo, $MoSi_2$, or Mo-N to copper penetration preventing Cu reaction with the substrate for 30min at a temperature higher than $650^{\circ}C$.

• 마이크로전자및패키징학회지
• /
• 제8권2호
• /
• pp.15-18
• /
• 2001

Magnetron sputtering 장비를 이용하여 극자외선 노광 공정용 Mo/Si 다층 박막을 증착하였다. 증착 파워로는 Mo의 경우 DC파워를, Si의 경우 RF파워를 이용하였다. 각각의 target에 인가되는 DC 또는 RF 파워의 시간 및 파워 조절을 통해서 원하는 구조인자를 가진 다층박막을 증착하였다. 증착된 다층박막을 단면 TEM, low/high angle XRD 등을 이용하여 박막의 미세구조와 interfacial layer의 거동을 살펴 보았으며, low angle XRD로부터 다층박막을 간접적으로 평가할 수 있었으며, 단면 TEM으로부터 Si위에 형성되는 Mo의 interfacial layer가 Mo위에 형성되는 경우보다 두꺼운 것을 알 수 있었다.

• 동력기계공학회지
• /
• 제17권4호
• /
• pp.109-114
• /
• 2013

In this study, the microstructure, mechanical properties and high temperature oxidation characteristics of HiSiMo and HiSiMoM ductile iron for exhaust manifold were investigated. The HiSiMoM ductile iron was developed by optimization of alloying element addition and casting design. The exhaust manifold prototype was fabricated using the HiSiMoM iron and this resulted in the weight saving of 0.73kg. The microstructures of the HiSiMo and HiSiMoM irons were similar each other and graphite nodularity was 89% and 93% respectively. Tensile strengths of them were 663.5 and 674.4 MPa and Brinell hardness were 235.3 and 243.9 respectively. Both irons showed parabolic weight gain behavior in high temperature oxidation atmosphere. Oxidation layer was divided into external and internal layers. The weight gain of the HiSiMoM iron was lower than that of the HiSiMo iron after isothermal oxidation test at $900^{\circ}C$. This should be rationalized by higher Si enrichment at the interface of the matrix and internal layer of the HiSiMoM iron.

• 대한기계학회논문집A
• /
• 제27권7호
• /
• pp.1132-1137
• /
• 2003

This study dealt with the suppression of interfacial reaction between Nb and MoSi$_2$ for the fabrication of high toughness Nb/MoSi$_2$ laminate composites, based on the results of a thermodynamical estimation. Especially, the effect of ZrO$_2$ particle on the interfacial reaction of Nb/MoSi$_2$ bonding materials has been examined. Nb/MoSi$_2$ bonding materials have been successfully fabricated by alternatively stacking matrix mixtures and Nb sheets and hot pressing in the graphite mould. The addition of ZrO$_2$ particle to MoSi$_2$ matrix is obviously effective for promoting both the interfacial reaction suppression and the sintered density of Nb/MoSi$_2$ bonding materials, since it is caused by the formation of ZrSiO$_4$ in the MoSi$_2$-ZrO$_2$ matrix mixture. The interfacial shear strength of Nb/MoSi$_2$ bonding materials also decreases with the reduction of interfacial reaction layer associated with the content of ZrO$_2$ particle and the fabrication temperature.

• 한국세라믹학회지
• /
• 제47권4호
• /
• pp.319-324
• /
• 2010

Screen printable $MoSi_2$ paste and its ceramic sheet heater were investigated. $MoSi_2$ powder without $Mo_5Si_3$ second phase, which causes so-called pest phenomena, was synthesized by SHS technique. Over glaze was also developed for preventing pest phenomenon. The maximum temperature of $MoSi_2$ ceramic heater was over $500^{\circ}C$. After several heat up and cooling cycle, the $MoSi_2$ heater reveals pest phenomenon. Conductive $MoSi_2$ paste could be used in electronic ceramics, i.e., MLCC, LTCC, HTCC, and etc.