• Analytical Science and Technology
• /
• v.17 no.1
• /
• pp.1-7
• /
• 2004

The synergistic solvent extraction of Mn(II) by N-nitroso-N-phenylhydroxylamineammonium salt (cupferron) and tetrabutylammonium ion ($TBA^+$) has been studied. In the presence of $TBA^+$, over 95% Mn(II) was extracted from an aqueous solution into chloroform by the cupferron in the pH range of 4 to 10. But a part of Mn(II) was extracted with only cupferron. The ternary complex of Mn(II) was more efficiently extracted into $CH_2Cl_2$ and $CHCl_3$ than other nonpolar solvents. The extracted Mn(II) was determined in the back-extracted $HNO_3$ solution by GF-AAS. This fixed procedure was applied to the determination of trace Mn(II) in tap water samples of pH 5.0. The detection limit equivalent to 3 times standard deviation of the background absorption was 0.37 ng/mL and Mn(II) was determined with the range of 0.4 to 1.01 ng/mL in our laboratory's tap water. And the recovery was 94 to 107% in samples in which 2.0 ng/mL Mn(II) was spiked. The interferences of common concomitant elements such as Cu(II), Ca(II), Fe(III) and so on were not shown up to $10{\sim}20{\mu}g/mL$. From these results, this procedure could be concluded to be applied for the determination of trace Mn(II) in other environmental water samples.

• Journal of Korea Foundry Society
• /
• v.34 no.5
• /
• pp.170-178
• /
• 2014

Using the Gleeble test, the effects of [Mn/S] ratios and the presence of sulfides on the high-temperature fracture morphology of heavy-section steel castings were analysed via the observations of the microstructures. The specimens for which the [Mn/S] ratio was in the range of 60~80 showed a ductile fracture morphology with an area reduction of more than 60%, while some specimens with similar [Mn/S] ratios showed a brittle fracture morphology with an area reduction of 0.0% due to the liquidation of sulfides at the grain boundary. The fracture morphology was classified into three types in the Gleeble high-temperature tensile test specimens. The first type showed dimple formation at the grain boundary, the formation of globular MnS sulfides, and plastic deformation of sulfides at an elevated temperature, indicating a needle-point type of ductile fracture with area reductions of 96.0~97.8%. The second type was a knife-edge type brittle fracture with an area reduction of 0.0% due to the film-type liquidation of sulfides at the grain boundary, band-type liquidation, and the liquidation of a terraced nipple pattern. The third type was the typical ductile fracture with an area reduction of 31.3~81.0%, in accordance with the mixture of dimples with in the grains and terraced nipple pattern at the grain boundary.

• Journal of Magnetics
• /
• v.5 no.2
• /
• pp.50-54
• /
• 2000

NiMn-pinned spin valve films consisting of a layered glass/NiFe/Co/Cu/Co/NiFe/NiMn/Ta stack were made by do magnetron sputtering. After deposition, the structure was annealed in a series of cycles each including three hours at $220^\circ C, 2\times10^{-6}$ Torr, in a field of 350 Oe, to create an ordered antiferromagnetic structure in the NiMn layer and produce a strong unidirectional pinning field in the pinned magnetic layer, Optimum spin valve properties were obtained after seven annealing cycles, or 21 hours at $220^\circ C$, and were : MR ratio 1%, exchange coupling field 620 Oe, and coercivity of pinned layer 250 Oe. The exchange coupling field remained constant up to an operating temperature of $175^\circ C$, and the blocking temperature was about $380^\circ C$.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.273-276
• /
• 2008

In this study, microstructure and distribution of alloy elements were investigated in thermo-mechanically processed C-Mn-Si transformation induced plasticity (TRIP) steels. The microstructures of TRIP steels were investigated by using advanced analysis techniques, such as three dimensional atom probe tomography (3D-APT). At first, the microstructure was observed by using TEM. TEM results revealed that microstructure of C-Mn-Si TRIP steel was composed of ferrite, bainte, and retained austenite. 3D-APT was used to characterize atomic-scale partitioning of added elements at the phase interface. In the retained austenite phase, Ti and B were enriched with C. However, there was no fluctuation of Mn and Si concentration across the interface. Through these analysis techniques, the advanced characteristics of constituent microstructure in C-Mn-Si TRIP steels were identified.

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.140-144
• /
• 1995

The role of Mn on the PTCR characteristics of La-doped BaTiO3 ceramics was studied. The calculated Ns value was increased with Mn concentration and consequently pmax and pmin were increased. The behavior of pmin was explained by the Jonker's theory, and Ns value of 6.35×1017m-2 was well agreed with the theoretical estimate of Jonker's. The value state of Mn was measured by ESR, and changed around Tc from ＋3 in tetragonal phase to ＋2 in cubic phase. Therefore, the amount of electron trap increased at Tc led to the great improvement of PTC R characteristics.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.2
• /
• pp.113-119
• /
• 1995

We have reported that an Fe-17wt%Mn alloy exhibits the highest damping capacity in the Fe-Mn binary system. In the present work, the effects of copper content on the damping capacity, atmospheric corrosion and mechanical properties were studied. The damping capacities were measured at room temperature for the air cooled Fe-17wt%Mn alloy having copper content from 0.1wt% to 1.1wt%. The damping capacity of the Fe-17wt %Mn alloy was decreased with increasing copper content. However, the addition of Copper was found to improve mechanical properties and atmospheric corrosion resistance. These mechanical properties were attributed to the formation of stress-induced martensite during tensile test.

• Journal of the Korean Ceramic Society
• /
• v.55 no.1
• /
• pp.55-60
• /
• 2018

In this study, quantum dots composed of $Mn^{2+}$ doped ZnS core and ZnS shell were synthesized using MPA precursor at room temperature. The ZnS: Mn/ZnS quantum dots were prepared by varying the content of MPA in the synthesis of ZnS shells. XRD, Photo-Luminescence (PL), XPS and TEM were used to characterize the properties of the ZnS: Mn/ZnS quantum dots. As a result of PL measurement using UV excitation light at 365 nm, the PL intensity was found to greatly increase when MPA was added at 15 ml, compared to the case with no MPA; the PL peaks shifted from 603 nm to 598 nm. A UV sensor was fabricated by using a sputtering process to form a Pt pattern and placing a QD on the Pt pattern. To verify the characteristics of the sensor, we measured the electrical properties via irradiation with UV, Red, Green, and Blue light. As a result, there were no reactions for the R, G, and B light, but an energy of 3.39 eV was produced with UV light irradiation. For the sensor using ZnS: Mn/ZnS quantum dots, the maximum current (A) value decreased from $4.00{\times}10^{-11}$ A to $2.62{\times}10^{-12}$ A with increasing of the MPA content. As the MPA content increases, the PL intensity improves but the electrical current value dropped because of the electron confinement effect of the core-shell.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.24 no.2
• /
• pp.93-104
• /
• 2004

This pot experiment was conducted to investigate the effects of combined micronutrient application($T_1$; control, $T_2$; Fe, $T_3$; Fe+Mn, $T_4$; Fe+Mn+Cu, $T_5$ ; Fe+Mn+Cu+Zn, $T_6$ ; Fe+Mn+Cu+Zn+Mo, T$_{7}$; Fe+Mn+Cu+Zn + Mo + B) on forage performance of pure and mixed cultures of orchardgrass and white clover. The fifth part was concerned with the changes in the total and relative contents, uptake amounts, and mutual ratios. of micronutrients in forages. The results obtained are summarized as follows: 1. The relative contents(total contents of 6 micronutrients = 100%) of Fe and Mn were considerably influenced by the antagonism between Fe and Mn, and also were influenced by the differences in Mn-absorption between orchardgrass and white clover. Compared with pure culture, orchardgrass showed high relative contents of Mn, and low relative contents of Fe and B in mixed culture. White clover, however, tended to be exactly opposed to the above trends. In relative contents, the T$_6$ 6/ resulted generally in decrease of Fe. However the $T_7$ resulted in increase of Mn and B. In addition, the $T_7$ resulted in decrease of Cu and Zn in orchardgrass, and Mo in white clover. 2. In general, there were differences in the tendency between the yield changes and the uptake amounts of micronutrients. General differences have been showed in the uptake amounts and mutual ratios of micronutrients based on the forage species, pure/mixed culture, additional fertilization, and antagonism. The uptake amounts of total micronutrients were generally increased by the treatments with increased combination. In uptake amounts, the $T_7$ resulted in the increase of Mn and B, and decrease of Mo. 3. The mutual ratios of Fe/Mn, Fe/Cu, and Mn/Cu were considerably influenced by the antagonism between Fe and Mn. At the $T_7$ , very low ratio of Fe/Mo affected by the T6 tended to be somewhat improved because of the decrease of Mo content． The poor growth of forages at the $T_6$ was improved by the $T_7$ . This fact was likely to be caused by the adequate B/Mo ratio.

• Journal of Technologic Dentistry
• /
• v.7 no.1
• /
• pp.41-51
• /
• 1985

This study has been to survey the present situation of satisfaction to the occupation and dental laboratory by means of selscting 200 dental technicians who are woked in Pusan, Deagu, Kwangju, Deajun. Questionaires were distributed to them and the summerized results were as follows; 1. In general, the dental technician's satisfaction of the occpation was revealed as moderate(Mn, 2.83), the dental technician's satisfaction of the laboratory was revealas moderate(Mn, 2.80). The highest degree item out of the satisfaction of occpation was the outlook(Mn, 3.23), and the lowest degree item was the advancement and the rise to a high position(Mn, 2.22). The highest degree item out of the satisfaction of laboratory was dental material(Mn, 3.07), and the lowest degree item was the equipment of dust collection(Mn, 2.49) 2. By age, the highest degree item out of the satisfaction of occpation was 30 to 43 group(Mn, 3.28), 50 and over group was the lowest degree item(Mn, 2.89). The highest degree item out of the satisfaction of laboratory was 40 to 50 group(Mn, 3.10), the lowest degree item was 35 to 39 group(Mn, 2.88). 3. By school career, the satisfaction of occpation and dental laboratory were higher in the graduated college group than the graduated highschool group. 4. By personal health state, the highest degree item of the satisfaction of occpation was the health group(Mn, 3.25). The highest degree item of the satisfaction of laboratory was the unhealthy group(Mn, 3.07). 5. By religion, the satisfaction if iccupation of laboratory ws higher in the religious group than the non-religious group. 6. By job career, the highest degree item of occupation satisfaction was 15 to 20 years group(Mn, 3.27), the lowest degree item was 20 and over group(Mn, 3.02). The highest degree item out of the satisfaction of laboratory was 15 to 20 years group(Mn, 3.05), The lowest degree item was 7 to 10 years group (Mn, 2.90). 7. By job position, the highest degree item out of satisfaction of occupation was the chief of laboratory group(Mn, 3.33), the head of laboratory group was the lowest degree item(Mn, 3.07). The hightest degree item out of the satisfaction of laboratory was the head of laboratory group(Mn, 3.10), the lowest degree item was the chief of laboratory group(Mn, 2.88). 8. By the place of employment, the degree of occpational satisfaction by items was found that the highest degree in the group engagel in general hospital(Mm, 3.43), the group engaged in dental clinic and hospital(Mn. 3.24), and the dental laboratory group(Mn. 3.14) in order. The difference among the group was significant emough(P<0.05). The highest degree item out of the satisfaction of laboratory was dental laboratory group(Mn. 2.70). The difference among the group was significant emough(P<0.01). 9. By monthly salary, the highest degree item out of the satisfaction of occupation was ￦500,000 to 600,000 group(Mn. 3.32), the lowest degree item was ￦600,000 and over group(Mn, 3.07). The highest degree item out of the laboratory satisfaction was ￦100,000 to 200,000 group(Mn, 3.03), the lowest degree group was ￦300,000 to 400,000 group(Mn, 2.95). 10. As compared with the degree of satisfaction according to job satisfaction, the highest degree item out of the occupational satisfaction was much satisfied group(Mn, 3.65), the lowest degree item was non-satisfied group(Mn, 2.68). The difference among the group was significant enough(P<0.05). The highest degree item out of the satisfaction of laboratory was non-satisfied group(Mn, 30.9), the lowest degree item was satisfied group(Mn, 2.84). The difference among the group was significant enough(P<0.01).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.291-291
• /
• 2009

ZnS:Mn/Cu,Cl 계 나노 형광체의 특성을 살펴보았다. 실험에서는 ZnS:Mn 과 ZnS:Cu,Cl 형광체 파우더를 이용하여 밀링을 통하여 분쇄하여 EL 소자를 제작하였다. 형광체 파우더를 볼밀에 $\Phi5mm$의 지르코나이 볼과 에탄올과 함께 넣고 2, 4, 6, 8, 10일간 밀링을 하였다. 밀링한 형광체 파우더를 SEM을 통하여 파우더의 사이즈를 관찰하였다. 또 이 파우더를 이용하여 EL 소자를 제작하였다. 소자의 구조는 기판은 알루미나 기판을, 하부 전극은 Au, 유전체는 $BaTiO_3$ 유전체 페이스트를 사용하였으며, 형광체 적층 후 ITO 전극을 스퍼터를 이용하여 증착하여 제작하였다. 제작한 소자를 이용하여 소자의 휘도 등 발광 특성을 살펴보았다.