• Korean Journal of Optics and Photonics
• /
• v.31 no.4
• /
• pp.169-175
• /
• 2020

We design a polarization-independent dielectric multilayer thin-film diffraction grating for a spectral-beam-combining (SBC) system with a simple grating structure and low aspect ratio. To maintain the high quality of the SBC beam, we propose a multilayer mirror structure in which the wavefront distortion due to stress accumulation is minimized. Moreover, to prevent light absorption from contamination, an optimized design to minimize the grating thickness was performed. The optimally designed diffraction grating has 99.36% diffraction efficiency for -1st-order polarization-independent light, for incidence at the Littrow angle and 1055-nm wavelength. It is confirmed that the designed diffraction grating has sufficient process margin to secure a polarization-independent diffraction efficiency of 96% or greater.

• Korean Journal of Optics and Photonics
• /
• v.16 no.6
• /
• pp.516-520
• /
• 2005

We proposed an efficient phase stepping method for the use in fiber-optic ESPI. To improve phase-stepping accuracy and efficiency, a fiber-optic Michelson interferometer was phase-modulated by a ramp-driven fiber stretcher, resulting in 4$\pi$ phase excursion in the PD interference signal. The zero-crossing points of the signal, which have consecutive $\pi$ phase difference, were carefully detected and used to generate trigger signals for the CCD camera. From the experimental results by using this algorithm, $\pi$/2 phase-stepping errors between the speckle patterns were measured to be less than 0.6 mrad with 100 Hz image capture speed. Also it has been shown that the error from the nonlinear phase modulation and environmental perturbations could be minimized without any feedback algorithm.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.4
• /
• pp.395-404
• /
• 2000

A damage detection and assessment algorithm is developed by measuring accelerations at limited locations of a structure under forced vibrations. The developed algorithm applies a time-domain system identification (SI) method that identifies a structure by solving a linearly constrained nonlinear optimization problem for optimal structural parameters. An equation error of the dynamic equilibrium of motion is minimized to estimate optimal parameters. An adaptive parameter grouping scheme is applied to localize damaged members with sparse measured accelerations. Damage is assessed in a statistical manner by applying a time-windowing technique to the measured time history of acceleration. Displacements and velocities at the measured degrees of freedom (DOF) are computed by integrating the measured accelerations. The displacements at the unmeasured DOF are estimated as additional unknowns to the unknown structural parameters, and the corresponding velocities and accelerations we computed by a numerical differentiation. A numerical simulation study with a truss structure is carried out to examine the efficiency of the algorithm. A data perturbation scheme is applied to determine the thresholds lot damage indices and to compute the damage possibility of each member.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.3
• /
• pp.237-243
• /
• 2012

The thickness optimization of the gearbox housing for 5MW wind turbine is carried out with the help of the efficient structure analysis model and the approximation model of objective function. Wind turbine gearbox is a complex structural system composed of a number of gear trains, shafts, bearing and gearbox housing, requiring a tremendous number of elements for the structural analysis and design. In this paper, an effective analysis and design model considering the tooth stiffness of helical gears is proposed. It enables to significantly reduce the total element number and the analysis time. Through the numerical optimization of housing thickness making use of the effective gearbox model and the approximate model of objective function, the total weight of the gearbox housing is minimized. It has been observed from the numerical experiment that the approximation model is reliable and the optimization result is acceptable and verified analysis.

• Nuclear Engineering and Technology
• /
• v.27 no.3
• /
• pp.336-343
• /
• 1995

The Self Tuning Regulator(STR) method which is an approach of adaptive control theory, is ap-plied to design the fully automatic power controller of the nonlinear reactor model. The adaptive control represent a proper approach to design the suboptimal controller for nonlinear, time-varying stochastic systems. The control system is based on a third­order linear model with unknown, time-varying parameters. The updating of the parameter estimates is achieved by the recursive extended least square method with a variable forgetting factor. Based on the estimated parameters, the output (average coolant temperature) is predicted one-step ahead. And then, a weighted one-step ahead controller is designed so that the difference between the output and the desired output is minimized and the variation of the control rod position is small. Also, an integral action is added in order to remove the steady­state error. A nonlinear M plant model was used to simulate the proposed controller of reactor power which covers a wide operating range. From the simulation result, the performances of this controller for ramp input (increase or decrease) are proved to be successful. However, for step input this controller leaves something to be desired.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.4
• /
• pp.303-310
• /
• 2017

Pressure retarded osmosis(PRO) has attracted much attention as potential technology to reduce the overall energy consumption for reverse osmosis(RO) desalination. The RO/PRO hybrid process is considered as the most logical next step for future desalination. The PRO process aims to harness the osmotic energy difference of two aqueous solutions separated by a semipermeable membrane. By using the concentrated water(RO brine) discharged from existing RO plants, the PRO process can effectively exploit a greater salinity gradient to reduce the energy cost of processing concentrated water. However, in order to use RO brine as the draw solution, PRO membrane must have high water flux and enough mechanical strength to withstand the high operational pressure. This study investigates the development of a thin film composite PRO membrane and spiral wound module for high power density. Also, the influence of membrane backing layer on the overall power density was studied using the characteristic factors of PRO membranes. Finally, the performance test of an 8-inch spiral wound module was carried out under various operating conditions(i.e. hydraulic pressure, flow rate, temperature). As the flow rate and temperature increased under the same hydraulic pressure, the PRO performance increased due to the growth of water permeability coefficient and osmotic pressure. For a high performance PRO system, in order to optimize the operating conditions, it is highly recommended that the flow pressure be minimized while the flow rate is maintained at a high level.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.5
• /
• pp.337-343
• /
• 2013

In this paper, IEEE 802.11 based WLAN(5.2/5.8GHz) wideband Weathercock-shaped microstrip patch antenna was designed and manufactured. The antenna has a size of $17.4{\times}17.4mm^2$ and utilized FR-4 board. The size was minimized for mobility, and Weathercock-shaped U-slot and short-pin was inserted to satisfy adequate bandwidth and double bandwidth resonance characteristics. In addition, the antenna incorporated single both-sided patch, and simulation design optimized the Weathercock-shaped, position of the U-slot and the short-pin, and the length of the patch for the measurement. The manufactured antenna achieved a bandwidth of 695MHz from 5.2~5.8GHz zone(Return loss<-10dB). Achieved a beam width of $81.13^{\circ}$ and $85.43^{\circ}$ for 3-dB beam width of H plane and E p;ane radiation pattern, there was 3.17~4.85dBi gain.

• The Journal of Society for e-Business Studies
• /
• v.4 no.1
• /
• pp.87-101
• /
• 1999

To operate the automatic devices of manufacturing process more effectively and to solve the needs of the resource sharing, network technology is applied to the control devices located in common manufacturing zone and operated by connecting them. In this paper, functional standard of the network layers are set as physical and data link layer of IEEE 802.2, 802.4, and VMD application layer and ISO-CIM reference model. Then, they are divided as minimized architecture, designed as group objects which perform group management and service objects which organizes and operates the group. For the stability in this network, this paper measures the variation of data packet length and node number and analyzes the variated value of the waiting time for the network operation. For the method of the analysis, non-exhausted service method are selected, and the arrival rates of the each data packet to the nodes that are assumed to form a Poission distribution. Then, queue model is set as M/G/1, and the analysis equation for waiting time is found. For the evalution of the performance, the length of the data packet varies from 10 bytes to 100 bytes in the operation of the group management network, the variation of the wating time is less than 10 msec. Since the waiting time in this case is less than 10 msec, response time is fast enough. Furthermore, to evaluate the real time processing of the group management network, it shows if the number of nodes is less than 40, and the average arrival time is less than 40 packet/sec, it can perform stable operation even taking the overhead such as software delay time, indicated packet service, and transmissin safety margin.

• Journal of the Korean Ceramic Society
• /
• v.43 no.12 s.295
• /
• pp.823-828
• /
• 2006

One of the main issues of Solid Oxide Fuel Cells (SOFCs) is to reduce the operating temperature to $750^{\circ}C$ or less. It has advantages of improving the life of component parts and the long-term stability of a system, so the production cost could be decreased. In order to achieve that, the ohmic and polarization loss of a single cell should be minimized first. This paper presents.to fabricate anode-supported single cells with controlling microstructure as a function of particle size and volume of graphite and NiO-YSZ weight ratio. By means of optimizing the manufactural condition through microstructure analysis and performance evaluation, the single cell which had NiO-YSZ=6:4, graphite volume of 24% and graphite size of $75{\mu}m$ as the anode composition showed a distinguished power density of $510mW/cm^2$ at $650^{\circ}C$ and $810mW/cm^2$ at $700^{\circ}C$, respectively.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.1
• /
• pp.40-49
• /
• 2008

Interior permanent magnet synchronous motor(IPMSM) has become a popular choice in electric vehicle applications and so of due to their excellent power to weight ratio. To obtain maximum efficiency in these applications, this paper proposes the neural network control method. The controllable electrical loss which consists of the copper loss and the iron loss can be minimized by the error back propagation algorithm(EBPA) of neural network. The minimization of loss is possible to realize eHciency optimization control for the IPMSM drive. This paper proposes high performance and robust control through a real time calculation of parameter variation such as variation of back emf constant, armature resistance and d-axis inductance about the motor operation. Proposed algorithm is applied IPMSM drive system, prove validity through analysis operating characteristics con011ed by efficiency optimization control.