• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.10a
• /
• pp.210-220
• /
• 2005

We have analyzed the stability for cut-slopes at main street 3-2 line section in Pa-ju local industrial complex. After studying an additional boring test, laboratory test and face mapping etc., we have determined the extent of reinforcement, slope inclinations and soil strength parameter from the analysis of test results. After changing the inclination of slopes for ground limit and carrying out the analysis of slope stability, we applied the Mass Nailing Method to the site because of need for reinforcement to soil and weathered rock slopes. In slope for soft and hard rock sections, we also reinforced the sections that are difficult to obtain the safety without reinforcement in alteration zone.

• Journal of Mechanical Science and Technology
• /
• v.14 no.11
• /
• pp.1244-1249
• /
• 2000

Burr and shape distortion are two main problems in micro-grooving. In this study, a simplified model is proposed based on large thrust force due to the tool edge radius. Experiments are conducted with a single crystal diamond tool on a 3-axis snaper-like machine varying the depth of cuts, and groove angles on brass, aluminum and OFHC. Experiments have shown that the thrust force becomes a dominant variable in burr generation compared to the principal force when the depth of cut is less than 2${\mu}m$. And fewer burrs develop on more brittle materials. Shape distortion is significant only when the groove angle is small and the depth of cut is larger than 30 ${\mu}m$.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.12
• /
• pp.21-26
• /
• 2011

This is a study to establish regulations against light pollution for lighting on roads. Many kinds of light pollution by luminaire on roads was calculated and analyzed by applying the classification method of luminaires(Cut-off classification of IDA-IESNA, BUG Rating Classification) and the calculation method of Upward Lighting Ratio of CIE among measures to prevent light pollution that international lighting organizations suggest. As a result of the analysis, it was found that the regulation by Cutoff of IESNA and ULR classification of CIE could be one for scattered light of light pollution compared to BUG classification but is not sufficient for the regulation of light tresspass or glare. BUG classification by each lighting zone was suggested as threshold value of the light pollution regulation considering domestic conditions.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.2
• /
• pp.125-130
• /
• 2011

This paper shows a method to design complementary filter using least square. The complementary filter is one of useful filters estimating angle. The basic concept of this filter is to enhance advantages of each sensor that angle detecting using a gyroscope has good accuracy at a high frequency and an accelerometer at a low frequency. When designing complementary filter, the most commonly used method is using cut-off frequency. However, it may be not easy to obtain a cut-off frequency. This paper presents a systematic method to determine the coefficients of the complementary filter using well-known linear least squares minimizing error between estimating angle and true angle.

• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.3
• /
• pp.56-61
• /
• 2002

CuFe$_2$O$_4$ ferrite was machined with cermet tools to clarify the machinability. The tool wear became the smallest at the cutting speed of 90m/min with the depth of cut of 0.2mm. The surface roughness became larger with increasing the cutting speed and the chamfer angle of tool. The tool with the chamfer angle of 15° showed the smallest wear. The surface roughness increased almost proportionally with the increase of chip size. The tool wear reduced with increasing feed in the depth of cut not more than 0.2mm.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.579-582
• /
• 1989

The air-cooled waterwheel generator has a fan connected to waterwheel shaft or motor driven fan or fans. The fans are operated at constant speed, constant input, regardless of generator loss which is varied according to generator output and coolant the perature. Energy savings may he possible if the cooling air flow is controlled according to generato output and air temperature depending on season. The simulation and experience have been done on the 22.6 KVA Waterwheel generator by using AC variable speed drive. The results gave us los cut of generator.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1148-1153
• /
• 2003

An adequate method for the prediction of machining errors is essential to improve productivity and product quality. But it is known that there is a remarkable difference between values calculated by conventional roughness model and measured values of actual machined surfaces under high efficient cutting condition. This paper introduces the theoretical analysis of characteristic lines of cut remainder to evaluate a geometrical surface roughness accurately. In this study, analytic equations of the characteristic lines are derived from the surface generation mechanism of ball end milling considering the actual trochoidal trajectories of cutting edges. The predicted results are compared with the results of conventional roughness model.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1132-1137
• /
• 2010

There are execute of new laws about prevent of earthquake diaster in nation because of some increments of big earthquake occurence frequency. Now develope new composit plate by ductile fiber with strong mechanic materials, which compose of strengthening systems for the underground structures subject to forced displacements. This study is to focus to develop the retrofitting system for the cut and cuver tunnels built without earthquake type load scenario, so that it can provide the safety of existing urban subway system against earthquakes.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.4
• /
• pp.65-72
• /
• 1990

After observing grinding characteristics according to variable grinding condition in order to raise the grinding effect without making worse the grinding quality by using general grinding machine, main conclusions of this study are as follows; 1) When grinding quality is constant, grinding effect is changed according to the speed of the workpiece. But the rapidly increasing critical speed of table is($V_w{\leq}4m/min$). 2) As grinding effect is equal, the lower the speed of the workpiece becomes, the lower the grinding force and surface roughness obtains good results. 3) In terms of grinding method, the down cut grinding method produces good grinding surface royghness in case of little grinding depth;otherwise, the up cut method in case of more grinding depth.

• Journal of Mechanical Science and Technology
• /
• v.14 no.10
• /
• pp.1114-1121
• /
• 2000

A flexible disk grinding process model was developed based on the dynamic relationship proposed by Kurfess and the influence of the major system parameters which potentially affect the grinding process was studied. Due to the process complexities, several new parameters were assumed to be kinematically dependent on the geometric layouts of the process. Different process stages had been defined depending on the kinematic relationships between the grinding disk and workpiece. A trend of depth of cut was simulated using the proposed model and compared with the empirically measured data in two dimensions. Due to a poor prediction capability of the first model, a modified model was proposed and a better performance has been proved to reveal a closer description of processed surface quality. Also a deflection length has been verified using a different analytical approach.