• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.495-498
• /
• 2006

This paper reports a high power 60 GHz push-push oscillator fabricated using 0.12 um metamorphic high electron-mobility transistors (mHEMTs). The devices with a $0.1{\mu}m$ gate-length exhibited good DC and RF characteristics such as a maximum drain current of 700 mA/mm, a peak gm of 660 mS/mm, and an $f_T$ of 170 GHz. By combining two sub-oscillators having $6{\times}50{\mu}m$ periphery mHEMT, the push-push oscillator achieved a 6.3 dBm of output power at 59.5 GHz with more than -35 dBc fundamental suppression. This is one of the highest output power obtained using mHEMT technology without buffer amplifier, and demonstrates the potential of mHEMT technology for cost effective millimeter-wave commercial applications.

• Journal of the Korean Ceramic Society
• /
• v.44 no.11
• /
• pp.597-606
• /
• 2007

With the advent of ubiquitous age, the high quality dielectric materials have been required for the wireless communications available to the millimeterwave as well as microwave frequencies. The utilizable region for the frequency has been expanding to the millimeter-wave region because of the shortage of radio frequency (RF) resources. These high frequencies would be expected for ultra high speed LAN, ETS and car anti-collision system on the intelligent transport system (ITS) and so on. Silicates are good candidates for microwave/millimeterwave dielectrics, because of their low dielectric constant ${\epsilon}_r$ and high quality factor (High Q). Forsterite ($Mg_2SiO_4$) is one of the silicates with low ${\epsilon}_r$ of 6.8 and Q f of 240000 GHz. In this paper, we reviewed following three categories for synthesis of forsterite: (1) Synthesis of high Q forsterite (2) Adjust the temperature coefficient of resonant frequency $TC_f$ (3) Diffusion of $SiO_{4^-}$ and Mg-ions on the formation of forsterite.

• Electrical & Electronic Materials
• /
• v.12 no.8
• /
• pp.39-45
• /
• 1999

Comparative photoresponsive current-volt-age characteristics of n-channel PHEMT and MESFET on GaAs substrate. with (W/L)=200${\mu}{\textrm}{m}$/1${\mu}{\textrm}{m}$ of gates, are reported as a function of electro-optical stimulation (P\ulcorner, λ=830nm) for the first time as far as we know. Significantly different photoresponses are observed in MESFET and PHEMT, mainly due to different optoelectronic mechanisms in the formation and current conduction of channel carriers. Under high optical power, high photoresponsity with a strong non-linearity with P\ulcorner, predominantly due to a parallel conduction via a heavily doped Al\ulcornerGa\ulcornerAs donor layer, was observed in PHEMT while the optically induced drain current has been very small but monotonically increasing with optical stimulation in GaAs MESFET. We also investigated differences in optically stimulated gate leakage currents and photonic gate responses on gate voltage and drain voltage as a function of P\ulcorner. Based on the drain and gate responses to electro-optical stimulation. PHEMTs are expected to be a better candidate for high performance photonically responsive microwave device compared with MESFETs.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.167-170
• /
• 2002

The design and fabrication of Q-band 3-stage monolithic microwave integrated circuit(MMIC) driver and power amplifiers for WLAN are presented using 0.2${\mu}{\textrm}{m}$ AlGaAs/InGaAs/GaAs pseudomorphic high electron mobility transistor(PHEMT). In each stage of the MMIC DA, a negative feedback is used for both broadband and good stability. The MMIC PA has employed a balanced configuration to overcome these difficulties and achieve high power with low VSWR over a wide frequency range. In the MMIC DA, the measurement results arc achieved as an input return loss under -4dB, an output return loss under -l0dB, a gain of 14dB, and a PldB of 17dB at C-band(36~ 44GHz). The chip size is 28mm$\times$1.3mm. The developed MMIC PA has the l0dB linear gain over 360Hz to 420Hz band and 22dBm PldB performance at 400Hz. The size of fabricated MMIC PA is 4mm x3mm. These results closely match with design results. This MMIC DA Sl PA will be used as the unit cells to develop millimeter-wave transmitters for use in wideband wireless LAN systems.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.1
• /
• pp.20-28
• /
• 2003

In this paper, we present results of the comparative analysis of the flicker phenomena in the poly-Si TFT-LCD and a-Si:H TFT-LCD arrays for the development and manufacturing of wide-area and high-quality TFT-LCD displays. We used four different types of TFTs; a-Si:H TFT, excimer laser annealed (ELA) poly-Si TFT, silicide mediated crystallization (SMC) poly-Si TFT, and counter-doped lateral body terminal (LBT), poly-Si TFT. We defined the electrical quantity of the flicker so that we could compare the flickers quantitatively for four different 40" UXGA TFT-LCDs. We identify three factors contributing to the flicker, such as charging time, kickback voltage and leakage current, and analyze how much each of three factors give rise to the flincker in the different TFT-LCD arrays. In addition, we suggest and show that, in the case of the poly-Si TFT-LCD arrays, the low-level (minimum) gate voltages should be carefully chosen to minimize the flicker because of their larger leakage currents compared with a-Si TFT-LCD arrays.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.4
• /
• pp.258-264
• /
• 2015

The first 77 GHz transceiver that applies a heterodyne structure-based linear frequency modulation-frequency shift keying (LFM-FSK) front-end module (FEM) is presented. An LFM-FSK waveform generator is proposed for the transceiver design to avoid ghost target detection in a multi-target environment. This FEM consists of three parts: a frequency synthesizer, a 77 GHz up/down converter, and a baseband block. The purpose of the FEM is to make an appropriate beat frequency, which will be the key to solving problems in the digital signal processor (DSP). This paper mainly focuses on the most challenging tasks, including generating and conveying the correct transmission waveform in the 77 GHz frequency band to the DSP. A synthesizer test confirmed that the developed module for the signal generator of the LFM-FSK can produce an adequate transmission signal. Additionally, a loop back test confirmed that the output frequency of this module works well. This development will contribute to future progress in integrating a radar module for multi-target detection. By using the LFM-FSK waveform method, this radar transceiver is expected to provide multi-target detection, in contrast to the existing method.

• Journal of Auto-vehicle Safety Association
• /
• v.5 no.1
• /
• pp.56-61
• /
• 2013

This paper presents a development of the Advanced Emergency Braking (AEB) Algorithm for passenger vehicles. The AEB is the system to slow the vehicle and mitigate the severity of an impact when a rear end collision probability is increased. To mitigate a rear end collision, the AEB comprises of a millimeter wave radar sensor, CCD camera and vehicle parameters of which are processed to judge the likelihood of a collision occurring. The main controller of the AEB algorithm is composed of the two control stage: upper and lower level controller. By using the collected obstacle information, the upper level controller of the main controller decides the control mode based not only on parametric division, but also on physical collision capability. The lower level controller determines warning level and braking level to maintain the longitudinal safety. To decide the braking level, Last Ponit To Brake and Steer (LPTB/LPTS) are compared with current driving statues. To demonstrate the control performance of the proposed AEBS algorithm's, closed-loop simulation of the AEBS was conducted by using the Matlab simlink and CarSim software.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.3
• /
• pp.23-27
• /
• 2013

This paper is for enhancing the breakdown voltage of MHEMTs with an InP-etchstop layer. Gate-recess structures has been simulated and analyzed for the breakdown of the devices with the InP-etchstop layer. The fully removed recess structure in the drain side of MHEMT shows that the breakdown voltage enhances from 2V to almost 4V and that the saturation current at gate voltage of 0V is reduced from 90mA to 60mA at drain voltage of 2V. This is because the electron-captured negatively fixed charges at the drain-side interface between the InAlAs barrier layer and the $Si_3N_4$ passivation layer deplete the InGaAs channel layer more and thus decreases the electron current passing the channel layer. In the paper, the fully-recessed asymmetric gate-recess structure at the drain side shows the on-breakdown voltage enhancement from 2V to 4V in the MHEMTs.

• Journal of electromagnetic engineering and science
• /
• v.6 no.1
• /
• pp.1-9
• /
• 2006

A sandwich structure of dielectric material and air gap inside a rectangular waveguide is proposed as a fast electrically tunable low-loss phase shifter. As the dielectric material is shifted up and down by piezoelectric actuator and, thereby, the thickness of air gap is changed, the effective dielectric constant of the sandwich structure is varied. Phase shifters based on the sandwich structure with different dielectric materials showed phase shift of $20{\sim}200^{\circ}/cm$ at X-band as the thickness of air gap varied up to $30{\mu}m$. The idea can be extended toward low-loss millimeter wave phase shifters since modem microwave ceramics have been developed to show very low dielectric loss$(tan\;{\delta}{\sim}10^{-4})$.

• 한국정보통신설비학회:학술대회논문집
• /
• 2005.08a
• /
• pp.115-119
• /
• 2005

In this paper, we propose a method that search the sweet spot of array antenna beam, and keep it for fast speed transmission in millimeter wave on single array antenna link. We use TDD(Time Division Duplex) as transfer method, and it transfers the control data of antenna. The proposed method is the modified genetic algorithm which selects a superior initial group through slave-processing in order to resolve the local solution of genetic algorithm. The efficiency of the proposed method is verified by means of simulations with white Gaussian noise and not on single array antenna link.