• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.14 no.1
• /
• pp.15-23
• /
• 2018

A compact heat exchanger is one of critical components in a very high temperature gas-cooled reactor (VHTR). Alloy 617 (Ni-Cr-Co-Mo) is considered as one of leading candidates for this application due to its excellent thermal stability and strengths in anticipated operating conditions. On the basis of current ASME code requirements, sixty sheets of this alloy are prepared for diffusion welding, which is the key technology to have a reliable compact heat exchanger. Optical microscopic analysis show that there are no cracks, incomplete bond, and porosity at/near the interface of diffusion weldment, but Cr-rich carbides and Al-rich oxides are identified through high resolution electron microscopic analysis. In high-temperature tensile testing, superior yield strengths of the diffusion weldment compared to the code requirement are obtained up to 1223 K ($950^{\circ}C$). However, both tensile strength and ductility drop rapidly at higher temperature due to the insufficient grain boundary migration across the interface of diffusion weldment. Best fit curves for minimum yield strength and average tensile strength are drawn from the experimental tensile results of this study.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.5
• /
• pp.213-221
• /
• 2021

In order to improve the energy density and safety of Li-ion batteries, the development of a separator with high thermal stability and electrolyte wettability is an important desire. Thus, the ceramic separator to replace the polymer type is one of the most promising materials that can prevent short-circuit caused by the formation of dendrite and thermal deformation. In this study, we introduce the fabrication of various anodic aluminum oxide membranes for the application of Li-ion battery separators with the advantages of improved mechanical/thermal stability, wettability, and a high rate of Li⁺ migration through the membrane. Two different types of through-holes and branched anodic aluminum oxide membranes are well used in lithium-ion battery separators, however, branched anodic aluminum oxide membranes exhibit the most improved performance with capacity (126.0 mAh g^-1 @ 0.3C), capacity drop at the high C-rate (30.6 %), and low internal resistance (8.2 Ω).

• The KIPS Transactions:PartC
• /
• v.18C no.5
• /
• pp.343-360
• /
• 2011

The objective of this paper is to analyze and characterize to simulate routing observations on end-to-end routing circuits and a ping experiment of a virtual network after modeling, such as IPv6 migration, an OSPFv3 routing experiment based on an IPv6 environment, and a ping experiment for IPv4/IPv6 dual-stack networks and IPv6 network for OSPFv3 routing using IPv6 planning and operations in an OPNET Modeler. IPv6 deployment based largely on the integrated wired and wireless network was one of the research tasks at hand. The previous studies' researchers recommended that future research work be done on the explicit features of both OSPFv3 and EIGRP protocols in the IPv4/IPv6 environment, and more research should be done to explore how to improve the end-to-end IPv6 performance. Also, most related work was performed with an IPv4 environment but lacked studies related to the OSPFv3 virtual network based on an end-to-end IPv6 environment. Hence, this research continues work in previous studies in analyzing IPv6 migration, an OSPFv3 routing experiment based on IPv6, and a ping experiment for IPv4/IPv6 dual-stack networks and IPv6 network for OSPFv3 routing. In the not too distant future, before enabling the default IPv6, it would help to understand network design and deployment based on an IPv6 environment through IPv6 planning and operations for the end-user perspective such as success or failure of connection on IPv6 migration, exploration of an OSPFv3 routing circuit based on an end-to-end IPv6 environment, and a ping experiment for IPv4/IPv6 dual-stack networks and IPv6 network for OSPFv3 routing. We were able to observe an optimal route for modeling of an end-to-end virtual network through simulation results as well as find what appeared to be a fast ping response time VC server to ensure Internet quality of service better than an HTTP server.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2359-2368
• /
• 2013

In this paper, an IRD (internal read data) circuit preventing the reentry into the read mode while keeping the read-out DOUT datum at power-up even if noise such as glitches occurs at signal ports such as an input signal port RD (read) when a power IC is on, is proposed. Also, a pulsed WL (word line) driving method is used to prevent a DC current of several tens of micro amperes from flowing into the read transistor of a differential paired eFuse OTP cell. Thus, reliability is secured by preventing non-blown eFuse links from being blown by the EM (electro-migration). Furthermore, a compared output between a programmed datum and a read-out datum is outputted to the PFb (pass fail bar) pin while performing a sensing margin test with a variable pull-up load in consideration of resistance variation of a programmed eFuse in the program-verify-read mode. The layout size of the 8-bit eFuse OTP IP with a $0.18{\mu}m$ process is $189.625{\mu}m{\times}138.850{\mu}m(=0.0263mm^2)$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.4
• /
• pp.398-406
• /
• 2022

In order to increase the electrochemical performance of thermal battery anode, LIFT anode having the same weight but a larger lithium content in electrodes was fabricated by mixing lithium, iron and titanium. By applying these electrodes, a single cell and a thermal battery were prepared, and the effect of LIFT anode on electrochemical performance was evaluated. The LIFT-applied single cell presented a better cell performance than LIFe-applied single cell at 500℃ and 550℃. The discharge performance of LIFT-applied single cell, which included the operating time (787s), specific capacity (1,683 Asg^-1), and electrode utilization (80.7%), was improved collectively compared to the LIFe applied single cell (736s, 1,245 As g^-1, and 74.6%) at 500℃. As the discharge progressed, the internal resistance of LIFT anode decreased, because the lithium migration path was formed due to the presence of large titanium particles among iron particles. These results were analyzed in terms of the microstructure of electrode using SEM. Energy density of LIFT-applied single cell also increased by 10% to 142.1 Wh kg^-1 compared to that of LIFe-applied single cell (127.4 Wh kg^-1). In addition, the LIFT-applied single cell presented a stable discharge performance for 6,500s without a short circuit which could occur by molten lithium under an open circuit voltage condition with a high pressure (4 kgf cm^-2). As observed in the high temperature thermal battery performance tests, the voltage and specific capacity of LIFT-applied thermal battery are superior to those of LIFe-applied thermal batteries, indicating that the energy density of LIFT-applied thermal batteries should remarkably increase.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.41-45
• /
• 2021

In this study, in order to secure the high reliability of the memristor, we adopted a patterned lithium filament seed layer as the main agent for resistive switching (RS) characteristic on the 30 nm thick ZrO₂ thin film at the device manufacturing stage. Lithium filament seed layer with a thickness of 5 nm and an area of 5 ㎛ × 5 ㎛ were formed on the ZrO₂ thin film, and various electrode areas were applied to investigate the effect of capacitance on filament type memristive behavior in the parallel memristive circuit of memristor and capacitor. The RS characteristics were measured in the samples before and after 250℃ post-annealing for lithium metal diffusion. In the case of conductive filaments formed by thermal diffusion (post-annealed sample), it was not available to control the filament by applying voltage, and the other hand, the as-deposited sample showed the reversible RS characteristics by the formation and rupture of filaments. Finally, via the comparison of the RS characteristics according to the electrode area, it was confirmed that capacitance is an important factor for the formation and rupture of filaments.

• Journal of Korea Multimedia Society
• /
• v.10 no.4
• /
• pp.462-469
• /
• 2007

ATM protocol has the techniques such as cell discarding priority, traffic shaping and traffic policing. ATM based MPLS(Multiprotocol Label Switching) is discussed for its provisioning QoS commitment capabilities, traffic engineering and smooth migration for BcN using conventional ATM infra in Korea. This paper proposes preventive congestion control mechanism for detecting HTR(Hard To Reach) LSP(Label Switched Path) in ATM based MPLS systems. In particular, we decide HTR LSP using real time signaling information(etc., PTI,AIS/RDI) for applying HTR concept in circuit switching to ATM based MPLS systems and use those session gap and percentage based control algorithm that were used in conventional PSTN call controls. We concluded that it maximized the efficiency of network resources by restricting ineffective machine attempts. Proposed control can handle 208% call processing and more than 147% success call, than those without control. It can handle 187% BHCA(Busy Hour Call Attempts) with 100 times less than use of exchange memory.

• Journal of Ecology and Environment
• /
• v.30 no.1
• /
• pp.23-38
• /
• 2007

Based on a time series of ocean climate indices and catch records for seven pelagic fish species in the Tsushima Warm Current (TWC) and Kuroshio-Oyashio Current (KOC) regions from 1910 to 2004, we detected regional synchrony in the long-term fluctuations of the fish populations and identified alternation patterns of dominant species related to climate shifts. The annual catches of Pacific herring, Japanese sardines, Japanese anchovies, jack mackerel, chub mackerel, Pacific saury and common squid in the TWC region fluctuated in phase with those in the KOC region, which suggests that they were controlled by the same basin-wide climate forcing. After the collapse of the herring fishery, the alternation sequence was: sardines (1930s), Pacific saury, jack mackerel, common squid and anchovies ($1950s{\sim}1960s$), herring ($late\;1960s{\sim}early\;1970s$), chub mackerel (1970s) and then sardines (1980s). As sardine biomass decreased in the late stages of the cool regime, catch of the other four species increased immediately during the warm period of the 1990s. Regional differences in the amplitude of long-term catch fluctuations for the seven pelagic fishes could be explained by regional differences in availability, fishing techniques and activity.

• International Journal of Concrete Structures and Materials
• /
• v.8 no.4
• /
• pp.289-299
• /
• 2014

Alkali-activated slag concretes are being extensively researched because of its potential sustainability-related benefits. For such concretes to be implemented in large scale concrete applications such as infrastructural and building elements, it is essential to understand its early and long-term performance characteristics vis-a'-vis conventional ordinary portland cement (OPC) based concretes. This paper presents a comprehensive study of the property and performance features including early-age isothermal calorimetric response, compressive strength development with time, microstructural features such as the pore volume and representative pore size, and accelerated chloride transport resistance of OPC and alkali-activated binder systems. Slag mixtures activated using sodium silicate solution ($SiO_2$-to-$Na_2O$ ratio or $M_s$ of 1-2) to provide a total alkalinity of 0.05 ($Na_2O$-to-binder ratio) are compared with OPC mixtures with and without partial cement replacement with Class F fly ash (20 % by mass) or silica fume (6 % by mass). Major similarities are noted between these binder systems for: (1) calorimetric response with respect to the presence of features even though the locations and peaks vary based on $M_s$, (2) compressive strength and its development, (3) total porosity and pore size, and (4) rapid chloride permeability and non-steady state migration coefficients. Moreover, electrical impedance based circuit models are used to bring out the microstructural features (resistance of the connected pores, and capacitances of the solid phase and pore-solid interface) that are similar in conventional OPC and alkali-activated slag concretes. This study thus demonstrates that performance-equivalent alkali-activated slag systems that are more sustainable from energy and environmental standpoints can be proportioned.

• Molecules and Cells
• /
• v.42 no.1
• /
• pp.45-55
• /
• 2019

The liver is involved in a wide range of activities in vertebrates and some other animals, including metabolism, protein synthesis, detoxification, and the immune system. Until now, various methods have been devised to study liver diseases; however, each method has its own limitations. In situ liver perfusion machinery, originally developed in rats, has been successfully adapted to mice, enabling the study of liver diseases. Here we describe the protocol, which is a simple but widely applicable method for investigating the liver diseases. The liver is perfused in situ by cannulation of the portal vein and suprahepatic inferior vena cava (IVC), with antegrade closed circuit circulation completed by clamping the infrahepatic IVC. In situ liver perfusion can be utilized to evaluate immune cell migration and function, hemodynamics and related cellular reactions in each type of hepatic cells, and the metabolism of toxic or other compounds by changing the composition of the circulating media. In situ liver perfusion method maintains liver function and cell viability for up to 2 h. This study also describes an optional protocol using density-gradient centrifugation for the separation of different types of hepatic cells, allowing the determination of changes in each cell type. In summary, this method of in situ liver perfusion will be useful for studying liver diseases as a complement to other established methods.