• Current Optics and Photonics
• /
• v.1 no.2
• /
• pp.118-124
• /
• 2017

Color rendering index (CRI) and luminous efficacy (LE) are two key performance factors of white LEDs (WLED). While most recent works in optics focus on methodology to improve these factors, little attention has been dedicated to chemical composition of materials. This paper studies the effect of $Sr_{2.4}1F_{2.59}B_{20.03}O_{74.8}:Eu_{0.12},Sm_{0.048}$ phosphor (SrSm), in terms of concentration and particle size on CRI and LE of 8500 K - WLEDs. Importantly, the molar mass of the componential ions in SrSm are calculated to shed light on the connection between the chemical composition of the material of interest and the performance of WLEDs. Results show that CRI can be improved to a value of around 86 by boosting red-light components in WLEDs, for all 3 major configurations: conformal, in-cup, and remote phosphor. CRI value tends to decrease with larger size of particles, while LE value goes in the reverse direction. On the other hand, both CRI and LE appear to be reduced at higher concentration of SrSm. This light attenuation is analyzed by using the Lambert-Beer law and Mie-scattering theory.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.2076-2081
• /
• 2004

Future exhaust gas limits for diesel-driven passenger cars will force the automotive industry to significantly improve the performance of engine. Since modern common-rail injection systems deliver more degrees of freedom referring to the injection process, again the optimization of the injection process could offer a possibility to meet the exhaust gas limits. This study describes the characteristic the pilot spray structure of piezo-driven injector for a passenger car common-rail system to be applicable multiple injection caused by fast response rather than solenoid-driven injector. The piezo-driven injector is prototype injector with same needle chamber of solenoid injector and the solenoid-driven one is commercial injector. The pilot spray characteristic such as spray tip penetration, spray speed, spray angle were obtained by spray images, which is measured by the Mie scattering method with optical system for high-speed temporal photography. It was found that piezo-driven injector effected electric change as important factor and showed faster response than solenoid-driven injector.

• Journal of the Korean Society of Combustion
• /
• v.17 no.4
• /
• pp.51-59
• /
• 2012

Experimental study in coflow jet flames has been conducted to investigate the helium-dilution effect of coflow air on self-excitation. For various helium mole fractions and jet velocities, two types of self-excitation were observed: buoyancy-driven self-excitation and Lewis-number-induced self-excitation(here after called Le-ISE) coupled with buoyancy-driven one. The difference between buoyancy-driven and Le-ISE is clarified by using the Mie-scattering visualization as well as exploring the different features. The mechanism of Le-ISE is proposed. When the system Damk$\ddot{o}$hler number was lowered, Le-ISE is shown to be launched. Le-ISE is closely related to heat loss, in that it can be launched in even methane jet flame (Lewis number less than unity) with helium-diluted coflow air. Particularly, Le-ISE becomes significant as the Damk$\ddot{o}$hler number decreases and heat-loss becomes significant.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.74-82
• /
• 2004

Planar laser-induced fluorescence(PLIF) has been widely used to obtain two dimensional fuel distribution. Acetone PLIF is chosen because fluorescence signal from acetone as a fluorescent tracer is less sensitive to oxygen quenching than other dopants. Acetone PLIF is applied to measure quantitative air excess ratio distribution in an engine fueled with LPG. Acetone is excited by KrF excimer laser (248nm) and its fluorescence image is acquired by ICCD camera with a cut-off filter to suppress Mie scattering from the laser light. For the purpose of quantifying PLIF signal, an image processing method including the correction of laser sheet beam profile is suggested. Raw images are divided by each intensity of laser energy and profile of laser sheet beam. Inhomogeneous fluorescence images scaled with the reference data, which is taken by a calibration process, are converted to air excess ratio distribution. This investigation shows instantaneous quantitative measurement of planar air excess ratio distribution for gaseous fuel.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.186-192
• /
• 2014

The spray structures under the stratified and homogeneous charge condition of a gasoline direct injection were investigated in a visualized constant volume chamber. The chamber pressure was controlled from 0.1 MPa to 0.9 MPa by the high pressure nitrogen and the chamber temperatures of $25^{\circ}C$, $60^{\circ}C$ and $80^{\circ}C$ were controlled by the band type heater. The fuel, iso-octane was injected by a 6-hole injector with the pressures of 7 MPa and 12 MPa. From the experiments results, it is confirmed that at lower chamber pressure, the penetration length and spray angle are mainly affected by the chamber temperature with the vaporization of the fuel droplets and generated vortices at the end region of the spray. And at higher chamber pressure, the penetration lengths at the end of the injection were about 50~60% of that at lower chamber pressure regardless of the chamber temperature and the effect of fuel injection pressure is larger than that of the chamber temperature which results from larger penetration lengths at higher fuel injection pressure than at lower fuel injection pressure regardless of the chamber temperatures.

• Journal of ILASS-Korea
• /
• v.28 no.1
• /
• pp.32-42
• /
• 2023

In this study, spray characteristics of n-heptane and propane were investigated under different injection pressure using various imaging techniques such as Mie-scattering, DBI (diffuse back-illumination), and Schlieren imaging techniques. NI compact RIO system was used to control a test injector. Spray penetration length, length-to-width ratio and number of black pixels were calculated by using MATLAB software to compare spray characteristics of each fuel. Longer spray penetration length and higher length-to-width ratio were observed in propane spray because of flash boiling caused by high saturated vapor pressure. Spray collapse occurred in propane spray due to the high plume-to-plume interaction. Moreover, rapid evaporation occurred in propane spray, so that nozzle tip wetting could not be observed. Rapid evaporation of propane also caused fewer residual droplets compared to n-heptane spray. Therefore, propane is advantageous in reducing the generation of soot emission from large droplets that are not atomized. However, additional evaluation should be conducted considering combustion efficiency and the possibility of deposits by nozzle tip icing during fuel injection.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.4 no.1
• /
• pp.18-26
• /
• 2001

Landsat TM band ratio algorithms were made by in-water optical measurement data of each sampling points for water quality monitoring of coastal area using Landsat TM satellite data. The algorithm was derived from in-water optical reflectance data which was measuring by the PRR(profiling reflectance radiometer). And, in-water optical reflectance data were applied to Landsat TM bands. Relationship between in-water optical reflectance and pigments proposed by the ratio of TM band 1 and band 2 showed to as follows; $Y=3.8352{\times}(R(band\;1)/R(band\;2))^{-2.1978}$ ($R^2$=0.7069) and, relationship of the ratio of TM band 1 and band 3 as follows; $Y=23.288{\times}(R(band\;1)/R(band\;3))^{-1.5243}$ ($R^2$=0.8062). Calculated the upwelling radiance of water surface and radiance of TM showed the ratio of atmospheric effect. In the coastal area Rayleigh and Mie scattering of atmosphere is to make over 80% of normalized radiance of Landsat TM. In order to apply in-water algorithm obtained by PRR, we had to calculate the atmospheric effects at sampling site. And, the quantitative analysis of in-water components using Landsat TM data need the calibration of in-water algorithm and effective method of atmospheric correction.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.107-111
• /
• 2020

Recently, as an aging society progresses, a lot of interest in health and diagnosis is increasing, As the field of various bio-imaging systems for guided surgery capable of accurate diagnosis has emerged as important, a Fluorescence imaging system capable of accurate measurement and real-time confirmation has emerged as an important field. Fluorescence images currently being used are mainly in the NIR-I band, but many studies are in progress in the NIR-II band in order to improve resolution and confirm fluorescence deeply and accurately. In this paper, the difference between NIR-I and NIR-II, optical characteristics, and SBR (signal to background ration) of a fluorescent imaging system, was investigated using the finite element (FEM) method. After confirming, it was confirmed that the SBR was 16.2 times higher in the NIR-II area than in the NIR-I by making the skin phantom and measuring the fluorescence. It is confirmed that the enhancement in SBR of the Fluorescence imaging system is more effective in the NIR-II region than in the NIR-I region and expected to be used in application fields such as guided surgery, bio-sensor and also device which can detect the defect of optical devices.

• Journal of ILASS-Korea
• /
• v.15 no.2
• /
• pp.74-82
• /
• 2010

In order to understand the behavior of transient gaseous injection used in an LPG (Liquefied Petroleum Gas) engine, turbulent incompressible transient jets with butane and propane were measured and analyzed at pressures of 1.5 bar and 2.0 bar with injector diameters of 3 mm and 5 mm. Mie-scattering method with a tracer was used, and images were processed to investigate the behavior of butane and propane jets. Distances from the nozzle to transition region were measured as $L_e/d_{inj}$=4.35~19.4, where $L_e$ and $d_{inj}$ indicate respectively a distance from nozzle to transition point and nozzle diameter. Slits and tubes around jet at near-field were introduced to measure the effect of entrainment and the diameter of jet, which revealed that the entrainment of surrounding air is significant for developing jet diameter. When the entrainment is restricted, the behavior of jet became deviating from the baseline. It was found that the virtual origin located outside of a nozzle towards jet tip within the conditions of this work, and its location was estimated as $x_o/d_{inj}$=0.56~7.25, where $x_o$ is a distance from nozzle to virtual origin.

• Atmosphere
• /
• v.29 no.5
• /
• pp.525-535
• /
• 2019

Vertical distributions of aerosol mass concentrations over Seoul and Gangneung from January to February 2015 were investigated using aerosol Mie-scattering lidars. Vertical mass concentration of aerosol was calculated from the lidar data using KALION's algorithm and quantitatively compared with ground PM₁₀ concentration to obtain objectivity of data. The backward trajectories calculated using HYSPLIT (version 4) were clustered into 5 traces for Seoul and 6 traces for Gangneung, and the observed aerosol vertical mass distribution was analyzed for individual trajectories. Result from the analysis shows that, aerosol concentrations with in the planetary boundary layer were highest when airflows into the measurement points originated in the Shandong Peninsula or the Inner Mongolia. In addition, the difference of aerosol mass concentrations in the two regions below 1 km was about twice as large as that in the long range transport from the Shandong Peninsula compared to the local emission. This result shows that the air quality over Korea related to particulate matters are affected more by aerosol emissions in the upstream source regions and the associated transboundary transports than local emissions. This study also suggests that the use of local aerosol observations is critical for accurate simulations of aerosol-cloud interactions.