• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.9
• /
• pp.1277-1283
• /
• 2013

In this paper, a novel voltage controlled oscillator(VCO) using CSRR loaded microstrip line for X-band RADAR is proposed. Using the microstrip line loaded CSRR inserted between the oscillator and buffer to the filter, the harmonic suppression has been improved. The measured results of the fabricated oscillator shows that its oscillation frequencies are from 9.28 to 9.39GHz according to the tuning voltage 0~10V, its output power level are about 16.6dBm at 9.35GHz. Compared with VCO using the conventional VCO, VCO using CSRR loaded microstirp, the harmonic suppression characteristic has been improved in 10.4dB

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.11
• /
• pp.54-59
• /
• 2007

In this paper, broadband voltage-controlled oscillator (VCO) using electronically controlled metamaterial transmission line based on varactor-loaded split-ring resonator (VLSRR) is presented. First, it is demonstrated that VLSRR coupled to microstrip line can lead to metamaterial transmission line with tuning capability. The negative effective permeability is provided by the VLSRR in a narrow band above the resonant frequency, which can be bias controlled by virtue of the presence of varactor diodes. The VCO with 1.8 V power supply has phase noise of $-108.84\;{\sim}\;-106.84\;dBc/Hz$ @ 100 Hz in the tuning range, $5.47\;{\sim}\;5.84\;GHz$. The figure of merit (FOM) called power-frequency-tuning-normalized (PFTN) is 20.144 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.760-767
• /
• 2005

In this paper, we proposed a new type SIR bandpass filter using DAMLs. This filter is consisted of 2 layers with MEMS resonator layer and CPW feed line. DAMLs ring resonator is elevated with $10{\mu}m$ height from GaAs substrate. Using MEMS processing, we are able to realize SIR bandpass filter easily. Furthermore it is useful to integrate on conventional MMICs because it has CPW interfaces and ring resonator is isolated from substrate by air-gap. We optimized and measured the results that $S_{21}$ attenuation at rejected band is over 15 dB, insertion loss is inside the limit of 3 dB, and relative bandwidth is about $10\%$ at 60 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.279-285
• /
• 2017

In this paper, the resonator with a parallel plate capacitor is newly proposed around sub-microwave frequency band and applied to earlobe for non-invasive glucose monitoring the human biological tissue. The capacitor including the earlobe as dielectric material is connected to inductive slot in the ground plane of the microstrip line. Based on the simulation, one port resonator circuit is designed and fabricated as a prototype. Three step glucose concentration levels(0, 250, 500 mg/dL) was tested, and its reflection coefficients($S_{11}$) were measured. Owing to high Q resonator more than 100, resonant frequency shift of about 9 MHz per glucose level of 250 mg/dL has been successfully measured. This proves that the proposed sensor is applicable to a blood glucose sensor.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.241-247
• /
• 2007

This paper introduces a new type push-push harmonic dielectric resonator oscillator. Proposed oscillators are utilized by HDRO(Harmonic Dielectric Resonator Oscillator) which are combined in push-push structure. As a result, fundamental signal suppression ratio and output power of harmonic signal has been improved. The increase of phase noise is compensated by improving coupling characteristic between resonator and parallel microstrip line. The proposed push-push HDRO shows the output power of 9.32 dBm, the fundamental signal suppression of -47.2 dBc and phase noise of -99.86 dBc at 100 kHz offset frequency and 18.7 GHz center frequency.

• Journal of the Korea Convergence Society
• /
• v.9 no.11
• /
• pp.29-35
• /
• 2018

In this paper, we proposed a high sensitivity sensor that can detect the concentration change of Nacl aqueous solutions by using a slot coupling capacitor resonator in sub-microwave band. The resonator applied to the sensor consists of a parallel plate capacitor connected to an inductive slot utilizing the ground plane of the microstrip line. Based on the measurement data of the dielectric characteristics according to the concentration change, the resonance frequency was determined in the UHF band where the concentration change is evident and the Nacl aqueous solution is inserted into the capacitor. Based on the simulation, the proposed resonator was designed and fabricated. The concentration level was varied from 0 to 400 mg/dl as 100 mg/dl step, and the transmission scattering coefficient ($S_{21}$) was successfully measured. Experimental results show that it is applicable to the concentration detection sensor in Nacl aqueous solution by obtaining minimum 1.8 dB($S_{21}$) at each step.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.1
• /
• pp.107-114
• /
• 2021

In this paper, a planar transistor oscillator for X-band using a newly proposed L-shaped monopole slot resonator is proposed. For planar design, an L-shaped monopole slot with an open-end is used as a resonator for a transistor oscillator. As a result of the simulated design of the resonator in three stages, a high Q value of 1169.84 and a high insertion loss of 49.934 dB were identified. The results of the final design and manufactured oscillator measurements confirmed that the oscillation output is greater than 7 dBm and has good phase noise characteristics of -58 dBc/Hz at 100 kHz offset. The proposed oscillator is planar and has the advantage of being directly applicable to microwave integrated circuit technology. It also has the advantage of being able to reduce its size as it can only be implemented in microstrip form without additional devices such as metal cavities and tuning screws in 3D structures, as in the case of a DRO (dielectric resonance oscillator).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.7
• /
• pp.1255-1260
• /
• 2009

Microstrip interdigital filter is designed with the width and length of a resonator, the gap distance between resonators and the location of a tap. When designing filters, it is a benefit to design with few design parameters comparing to many design parameters. In this paper we design and implement two microstrip interdigital filters operating in the UWB(Ultra Wide-Band) frequency band, one using a fixed width of a resonator and the other using a different width of resonators. The test results of the implemented filters show that the low-band high filter with a fixed width has the insertion loss of 1.49dB, -10dB band width of 720MHz, -35.7dBattenuation at 4.8GHzand below -13dB of S11. The filter with a different width of resonators has the insertion loss of 1.6dB, -10dBbandwidth of 1.63GHz and below-8dBof S11.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.1
• /
• pp.17-24
• /
• 2014

In this paper, we analysed coupling coefficient between dielectric resonator of high dielectric constant and microstrip line to design for low phase noise dielectric resonator by direct coupling. Also we analysed phase noise of dielectric resonance oscillator with parallel feedback circuit to complement Q by high dielectric constant. We obtained a result from high-stability dielectric oscillator which is optimum designed through analysis of dielectric resonance oscillator phase noise and coupling coefficient. The result is that the phase noise was -83.3dBc/Hz@1KHz at 20.25GHz when we used about 3.6 coupling coefficient and ${\epsilon}_r$=30 dielectric resonator of 20.25GHz dielectric resonance oscillator. As a result, we suggested the direct-connect design method by frequency multiplication mode to prevent phase noise loss at K-Band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.5
• /
• pp.544-552
• /
• 2010

In this paper, a new method to enhance the stop bandwidth of the compact microstrip bandstop filter based on split ring resonator(SRR) was proposed. To achieve wide stop bandwidth, we incorporated the SRR within the circular etched pattern of the defected ground structure(DGS). By incorporating the SRR within the circular etched pattern, a high magnetic coupling between SRR and signal line can be achieved. The high magnetic coupling enables the proposed structure to achieve a wide stop bandwidth. To verify the feasibility of the proposed structure, the proposed bandstop filter was compared with conventional bandstop filter employing SRRs which have been etched at both sides of the signal line. Simulation and experimental results show that the proposed structure provides an enhanced stop bandwidth compared with the conventional structure.