• 대한기계학회논문집B
• /
• 제28권12호
• /
• pp.1549-1556
• /
• 2004

We have deigned, fabricated and compared four different types of static chaos microfluid mixers, including the mixers using straight channel flow, microblock-induced alternating whirl flow, microchannel-induced lamination flow, and combined alternating whirl-lamination flow. Among them, the alternating whirl-lamination (AWL-type) mixer, composed of 3-D rotationally arranged microblocks and dividing microchannels fabricated by conventional planar lithography process, is effective to reduce the mixing length over wide flow rate ranges. We characterize the performance of the fabricated mixers, through the flow visualization technique using phenolphthalein solution. We verify that the AWL-type microfluid mixer shows the shortest fluid mixing length of 2.8mm∼5.8mm for the flow rate range of Re=0.26∼26 with the pressure drop lower than 5kPa. Compared to the previous mixers, requiring the mixing lengths of 7∼17mm, the AWL-type microfluid mixer results in the 60% reduction of the mixing lengths. Due to the reduced mixing lengths within reasonable pressure drop ranges, the present micromixers have potentials for use in the miniaturized Micro-Total-Analysis-Systems($\mu$TAS).

• 한국건설순환자원학회논문집
• /
• 제10권3호
• /
• pp.269-275
• /
• 2022

본 연구에서는 포졸란 혼화재 혼입에 따라 응결시간과 역학적 특성을 평가하였다. 응결시간 발현 특성은 포졸란 혼화재를 사용하였을 때 감소되는 효과와 압축강도가 증가되는 특성을 평가하였다. 포졸란 혼화재의 경우 단독으로 사용할 경우 마이크로 실리카가 초결 및 종결시간 단축 및 압축강도 발현에 효과적이였다. 두가지 이상의 혼화재를 사용하였을 때는 실리카흄을 사용하면서 동시에 소량의 나노 실리카를 사용하는 것이 OPC 대비 응결시간이 62~64 %수준으로 감소하였으며, 강도 수준이 약 1.17배 증가로 성능증진에 효과적이었다. 나노 실리카가 소량의 혼입량으로 응결시간 감소 및 압축강도를 증진시킬 수 있는 것은 포졸란 반응을 일으킴과 동시에 작은 입자크기로 상대적으로 큰 입자로 구성되어있는 실리카 흄과 시멘트 사이의 공극채움 효과가 있는 것으로 판단된다. 하지만 나노 소재의 경우 높은 비표면적으로 흐름성 저하의 원인이 되기 때문에 배합 설계 시 화학혼화제의 첨가가 고려되어야 할 것으로 판단된다.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2007년도 추계학술대회
• /
• pp.116-118
• /
• 2007

Three-dimensional (3D) velocity field information of a laminar flow in a curved micro tube of circular cross-section has been measured using a digital micro holographic particle tracking velocimetry (HPTV). The temporal evolution of instantaneous velocity field of a water flow in a curved micro tube of $100\;{\mu}\;m$ and $300\;{\mu}\;m$ in inner diameter was obtained. The 3D mean velocity field distribution was obtained quantitatively by statistical-averaging of instantaneous velocity fields. At low Dean number (De), a secondary flow was not generated in the curved tube. With increasing Dean number, the secondary flow constituted of two large-scale counter-rotating vortices was formed due to enhanced centrifugal force. To reveal the flow characteristics of high Dean numbers, trajectories of fluid particles were evaluated experimentally from the 3D velocity fields data measured by the HPTV technique. The present experimental results, especially the 3D particle trajectories, would be helpful to design and to understand the mixing phenomena in 3D curved passages of various curved micro-tubes or micro-channels.

• 한국표면공학회지
• /
• 제46권1호
• /
• pp.22-28
• /
• 2013

$WS_2$ particles were added to micro-diamond blades with Cu/Sn binding metal as lubricants to improve cutting efficiency. It was found in previous works that the added $WS_2$ lubricant could reduce remarkably the momentary energy consumption during dicing tests but increased wear rate slightly owing to weak bonding between lubricant particles and bond metals. In the present work, the surface of $WS_2$ lubricant particles were etched for activating the surface of $WS_2$ particles that provide even distribution of particles during powder mixing process and improvement of wetting at the interfaces between $WS_2$ particles and molten Cu/Sn bond metals during pressurized sintering so that could provide the improved strength of micro-blades and result in extended life. Chipping behavior of workpiece with the types of micro-blades including $WS_2$ were compared because it is important in semiconductor and micro-packaging industries to control average roughness and straightness of sliced surface which is closely related with quality.

• 전기학회논문지
• /
• 제67권9호
• /
• pp.1181-1188
• /
• 2018

In order to develop new insulating materials for GIS Spacer using environmentally friendly insulating gas, three kinds of dispersed liquid nano composites of solid epoxy /nano layered silicate filled material were prepared. And the epoxy/nano/micro silica composite was prepared by mixing epoxy/nano 3 phr dispersion/4 kinds of filler contents(40,50,60, 70wt%). The electrical insulation breakdown strengths of the nano and nano/micro mixed composites were evaluated by using 8 kinds of samples including the original epoxy. The mechanical tensile strength of the epoxy / nano / micro silica composite were evaluated, also. The TEM was measured to evaluate the internal structure of nano/micro composites. As a result, it was confirmed that the layered silicate nano particles was exfoliated through the process of inserting epoxy resin between silicate layers and the layers. In addition, dispersion of nano / micro silica resulted in improvement of electrical insulation breakdown strength with increase of filling amount of dense tissue with nanoparticles inserted between microparticles. In addition, the tensile strength showed a similar tendency, and as the content of microsilica filler increased, the mechanical improvement was further increased.

• Environmental Engineering Research
• /
• 제16권1호
• /
• pp.47-51
• /
• 2011

The oxygen transfer rate is a parameter that characterizes the gas-liquid mass transfer in surface aerators. Gas-liquid transfer mechanisms in surface aeration tanks depend on two different extreme lengths of time; namely, macromixing and micromixing. Small scale mixing close to the molecular level is referred to as micromixing; whereas, macromixing refers to mixing on a large scale. Using experimental data and numerical simulations, macro- and micro-scale parameters describing the two extreme time scales were investigated. A scale up equation to simulate the oxygen transfer rate with micromixing times was developed in geometrically similar baffled surface aerators.

• 한국염색가공학회지
• /
• 제9권1호
• /
• pp.23-32
• /
• 1997

Composite membranes having different mixing ratio of Wool(SCMK) and poly(ethylene terephthalate) (PET) were prepared by dissolving wool/PET in hexafluoro-2-propanol(HFIP), casting the obtained solution on a glass plate and evaporation the solvent in the presence and absence of an electric field. The internal structure of the prepared membrane was investigated using polarise microscope dyeing and dye permeation method. In the composite membrane prepared under electric field, both components were micro mixing, while in the membranes prepared under nonelectric field, the two components formed a random sea/island structure according to different mixing ratio. Such characteristic membrane structure was influenced the permeation behavior of C.I. Acid Red 118 through the membranes from an aqueous solution.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2007년도 춘계학술대회 논문집
• /
• pp.85-88
• /
• 2007

A number of R, G and B LEDs for reference color temperature mixing ratio of RGB was determined by the theory of RGB mixing as a baseline. Once the number of LEDs was determined the objective color temperature from baseline has been achieved by the control the RGB duty ratio. And a practical prototype of 50W floodlighting adjusted by the above algorithm. The micro controller was developed with control algorithm for RGB duty ratio to obtain the objective color temperature. Detailed experiments to optimize algorithm of duty ratio and color temperature will be discussed in this paper as well.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1016-1020
• /
• 2003

In this paper, we present a technology of producing anew chaotic micromixer, named Micromixer with Arranged Blocks(MAB), and the experimental result of the mixing performance. Chaotic mixing was successfully achieved by introducing periodic perturbation in the field of the channel flow by means of slanted blocks. The MAB was made by an RP(Rapid Prototyping) technology. We performed flow visualization experiments for the quantification of the mixing performance with the MAB. Lyapunov exponent was measured to be 0.3557 and 0.1305 for the block height 0.8 and 0.2 times the channel width.

• Advances in concrete construction
• /
• 제9권1호
• /
• pp.55-70
• /
• 2020

In this research article, acid resistance, sulphate resistance and sorptivity of self compacted concrete (SCC) prepared from C&D waste have been discussed. To improve the above properties of self compacted recycled aggregate concrete (SCRAC) along with mechanical and durability properties, different two stage mixing approaches (TSMA and TSMAsfc) were followed. In the proposed two stage mixing approach (TSMAsfc), silica fume, a proportional amount of cement and a proportional amount of water were mixed in premix stage which fills the pores and cracks of recycled aggregate concrete (RAC). The concrete specimen prepared using above mixing approaches were immersed in 1% concentration of sulphuric acid (H2SO4) and magnesium sulphate (MgSO4) solution for 28, 90 and 180 days for evaluating the acid resistance of SCRAC. Experimental results concluded that the proposed two stage mixing approach (TSMAsfc) is most suitable for acid resistance and sulphate resistance in terms of weight loss and strength loss due to the elimination of pores and cracks in the interfacial transition zone (ITZ). In modified two stage mixing approach, the pores and cracks of recycled concrete aggregate (RCA) were filled up and make ITZs of SCRAC stronger. Microstructure analysis was carried out to justify the reason of improvement of ITZs by electron probe micro analyser (EPMA) analysis. X-ray mapping was also done to know the presence of strength contributing elements presents in the concrete sample. It was established that SCRAC with modified mixing approach have shown improved results in terms of acid resistance, sulphate resistance, sorptivity and mechanical properties.