변형과 파손 등의 공용성능 문제가 발생하고 있는 아스팔트 포장과 콘크리트 포장에 비해 내구성능이 우수한 에폭시와 세라믹스를 결합한 혼합물을 도로포장에 적용하기 위하여 실내물성실험을 수행하고 현장에 적용하였다. 본 연구는 부착력과 내구성이 뛰어나 구조물 보수, 보강에 널리 사용되는 에폭시를 도로포장에 적용하기 위해서 세라믹스와 금속성분 등의 micro powder를 첨가하여 포장 재료로써의 공용성능을 확인하고 이를 현장에 적용하여 작업성과 시공성 등을 확인하였다. 콘크리트포장 현장의 시험시공은 파손된 기존 포장구간에 면처리 후 7 mm 박층으로 시공하였고, 아스팔트포장 현장의 시험시공은 파손된 기존 포장구간에 면처리 후 15 mm 박층으로 시공하여, 12개월 가량 균열 및 변형 발생여부를 관찰하였다. 에폭시와 세라믹스를 결합한 혼합물은 기존 포장과의 부착력이 뛰어났으며, 변형과 파손에 대한 저항성이 기존 포장재료에 비해 우수한 것으로 나타나 이를 도로현장에 적용할 경우, 공용성능 및 공용년한의 향상이 기대된다.
본 연구에서는 치핑작업중에 콘크리트에 발생할 수 있는 손상균열을 정량분석하기 위해 X-ray CT 이미지를 이용하는 방법을 제안하고자 한다. 이를 위해 치핑작업을 수행한 후, 균열이 발생한 콘크리트 블록을 코어링하여 직경 50 mm, 길이 100 mm의 시편을 준비하였다. 그 후 마이크로 포커스 X-ray CT 촬영을 하여 얻은 이미지를 3D 이미지로 재구성(reconstruction)하였다. 이렇게 얻어진 3D CT 이미지에 3DMA (3 Dimensional Medial axis Analysis)법을 적용하여, 손상 평가 파라메타로 시편의 위치에 따라 균열의 성질을 평가하여 손상을 분석하였다. 분석결과 치핑에 의한 손상은 치핑 표면으로부터 3 cm 깊이까지 발생한 것으로 나타났다. 또한 CT이미지 공간분석법에서 사용되는 여러 파라메타 중 공극률 지표(Porosity index), Burn number 그리고 Medial axis 의 파라메타를 이용해 치핑표면 근처의 손상 분석이 가능하다는 것이 확인되었다. 이 방법은 내부구조에 변화가 발생한 암석을 대상으로 한 연구에서도 비파괴 상태로 내부의 균열 평가, 가시화에 적용가능하다.
The domestic pine was used to investigate the change of specific gravity, moisture contents, color and anatomical structure by accelerated weathering test (AWT). According to visual inspection, a few knot separation and looseness as well as considerable surface discoloration was found out. However, the crack and split of surface texture have been never occurred till the last step of AWT. On the whole, as the time of accelerated weathering test has increased, the specific gravity has decreased. Finally, after the 9th week of AWT, the specific gravity was 0.38 that reached to 82% compared to the control specimen. In case of moisture content (MC), it showed rising trend in its early stages, however, after 3th week of AWT it have displayed steady state. A deterioration of cell-wall components was not remarkably observed by scanning electron microscope (SEM), however the ray fractures of AWT specimen were observed more than those of control specimen. The full fracture of epithelial cell around resin canal was observed by optical microscope. The fracture of ray of 2th cycle AWT specimen was first, followed by 1th week and control group. A distortion of tracheid for early spring wood and fracture of epithelial cell were generally observed by a similar level, regardless of duration time of AWT. Therefore, it is obvious that increasing duration time of AWT does not affect the deterioration of micro-structure for wood members from this study. Although a considerable change of anatomical properties was not found, there is a need of further research to understand how will the changes of specific gravity and MC on the physical properties of wood member.
고속 비상체에 의한 충격을 받는 시멘트 복합체는 표면관입, 배면박리 및 관통 등 국부적인 파괴거동을 보이며, 섬유혼입에 의한 휨인성의 향상으로 인해 배면파괴를 억제할 수 있다. 이에 섬유보강 시멘트 복합체의 내충격 성능에 관한 연구가 진행되고 있으며, 다양한 종류의 섬유보강재가 개발되고 있다. 섬유보강재의 종류에 따라 섬유와 매트릭스의 부착성능, 비표면적, 혼입개체수 등이 다르기 때문에 섬유보강 시멘트 복합체의 역학특성 및 고속 충격에 의한 내충격 성능의 향상에 미치는 효과에 대하여 검토할 필요가 있다. 본 연구에서는 성상 및 물성이 다른 강섬유(Steel fiber), 폴리아미드(Polyamide), 나일론(Nylon) 및 폴리에틸렌(Polyethylene)섬유를 혼입하여 섬유 종류에 따른 휨인성의 향상과 고속 비상체 충돌에 대한 파괴저감효과에 대하여 평가하였다. 그 결과, 혼입섬유의 가교작용에 의한 응력의 재분배 및 균열발생의 억제로 인해 휨인성이 향상되었으며, 고속충격에 의한 배면파괴를 억제할 수 있었다. 또한, 동일 충격에너지에서의 배면파괴한계두께를 감소시킬 수 있어 방호시설물에 적용할 경우 부재두께의 저감이 가능할 것으로 판단된다. 한편, 강섬유보강 시멘트복합체의 경우 배면박리가 발생하였으나, 섬유와 매트릭스의 부착에 의한 일부 파편의 박리가 억제되었으며, 합성섬유보강 시멘트복합체는 섬유의 혼입개체수가 많아, 고속충격에 의한 충격파의 상쇄작용 및 에너지 분산에 의한 미세균열이 발생해 배면파괴억제효과가 큰 것으로 판단된다.
Titanium oxide (TiO2) thin films have valuable properties such as a high refractive index, excellent transmittance in the visible and near-IR frequency, and high chemical stability. Therefore it is extensively used in anti-reflection coating, sensor, and photocatalysis as electrical and optical applications. Specially, TiO2 have a high dielectric constant of 180 along the c axis and 90 along the a axis, so it is highlighted in fabricating dielectric capacitors in micro electronic devices. A variety of methods have been used to produce patterned self-assembled monolayers (SAMs), including microcontact printing ($\mu$CP), UV-photolithotgraphy, e-beam lithography, scanned-probe based micro-machining, and atom-lithography. Above all, thin film fabrication on $\mu$CP modified surface is a potentially low-cost, high-throughput method, because it does not require expensive photolithographic equipment, and it produce micrometer scale patterns in thin film materials. The patterned SAMs were used as thin resists, to transfer patterns onto thin films either by chemical etching or by selective deposition. In this study, we deposited TiO2 thin films on Si (1000 substrateds using titanium (IV) isopropoxide ([Ti(O(C3H7)4)] ; TIP as a single molecular precursor at deposition temperature in the range of 300-$700^{\circ}C$ without any carrier and bubbler gas. Crack-free, highly oriented TiO2 polycrystalline thin films with anatase phase and stoichimetric ratio of Ti and O were successfully deposited on Si(100) at temperature as low as 50$0^{\circ}C$. XRD and TED data showed that below 50$0^{\circ}C$, the TiO2 thin films were dominantly grown on Si(100) surfaces in the [211] direction, whereas with increasing the deposition temperature to $700^{\circ}C$, the main films growth direction was changed to be [200]. Two distinct growth behaviors were observed from the Arhenius plots. In addition to deposition of THe TiO2 thin films on Si(100) substrates, patterning of TiO2 thin films was also performed at grown temperature in the range of 300-50$0^{\circ}C$ by MOCVD onto the Si(100) substrates of which surface was modified by organic thin film template. The organic thin film of SAm is obtained by the $\mu$CP method. Alpha-step profile and optical microscope images showed that the boundaries between SAMs areas and selectively deposited TiO2 thin film areas are very definite and sharp. Capacitance - Voltage measurements made on TiO2 films gave a dielectric constant of 29, suggesting a possibility of electronic material applications.
현탁중합에 이은 프리델 크래프츠 촉매에 의한 hyper crosslinking 반응 및 hydrolysis반응으로 hydroxyl 반응 관능기를 포함하는 hyper crosslinked polymer particle(HCPP)을 합성할 시, 1) 각 단량체의 함량 변화에 따른 HCPP의 표면 모폴로지, 기공 크기 및 분포도의 변화, 2) hyper crosslinking 반응조건 변화에 따른 HCPP의 BET 비표면적 값의 변화 및 3) $CO_2$ 초임계 건조공정을 이용한 HCPP에서의 미반응 잔류 단량체, 올리고머 및 촉매의 제거 등에 관해 연구하였다. 이번 연구를 통해 초기 HCPP의 합성 시 관찰되었던 고분자 입자 표면의 균열 및 파괴현상은 hyper crosslinking 과정 중에 진행되는 microphase separated domain간의 반응과 깊은 관계가 있음을 관찰하였고, 또한 hyper crosslinking 반응 시 반응온도 반응시간 및 사용 용매의 증가는 HCPP의 BET 비표면적 값의 증가에 기여함을 관찰하였다. 그리고 hyper crosslinking을 유발하는 단량체의 함량변화는 다른 단량체에 비해 HCPP의 BET 비표면적, 기공 크기 및 분포도에 상대적으로 큰 영향을 미침을 확인하였다. 또한 HCPP에서의 미반응 잔류 단량체, 올리고머 등의 제거에 $CO_2$ 초임계 건조공정이 매우 효과적임을 확인할 수 있었고 특히 이 과정에서의 보조용매(메탄올)의 첨가는 잔류촉매(Fe)의 제거에 있어 탁월한 효과를 나타내었다.
Joshi, Digesh D.;Patel, Paresh V.;Rangwala, Husain M.;Patoliya, Bhautik G.
Advances in concrete construction
/
제9권3호
/
pp.235-248
/
2020
Progressive collapse in a structure occurs when load bearing members are failed and the adjoining structural elements cannot resist the redistributed forces and fails subsequently, that leads to complete collapse of structure. Recently, construction using precast concrete technology is adopted increasingly because it offers many advantages like faster construction, less requirement of skilled labours at site, reduced formwork and scaffolding, massive production with reduced amount of construction waste, better quality and better surface finishing as compared to conventional reinforced concrete construction. Connections are the critical elements for any precast structure, because in past, major collapse of precast structure took place because of connection failure. In this study, behavior of four different precast wet connections with U shaped reinforcement bars provided at different locations is evaluated. Reduced 1/3rd scale precast beam column assemblies having two span beam and three columns with removed middle column are constructed and examined by performing experiments. The response of precast connections is compared with monolithic connection, under column removal scenario. The connection region of test specimens are filled by cast-in-place micro concrete with and without polypropylene fibers. Performance of specimen is evaluated on the basis of ultimate load carrying capacity, maximum deflection at the location of removed middle column, crack formation and failure propagation. Further, Finite element (FE) analysis is carried out for validation of experimental studies and understanding the performance of structural components. Monolithic and precast beam column assemblies are modeled using non-linear Finite Element (FE) analysis based software ABAQUS. Actual experimental conditions are simulated using appropriate boundary and loading conditions. Finite Element simulation results in terms of load versus deflection are compared with that of experimental study. The nonlinear FE analysis results shows good agreement with experimental results.
A defect could be generated in bolts for a use of oil filters for the manufacturing process and then may affect to the safety and quality in bolts. Also, fine defects may be imbedded in oil filter system. So it is very important that such defects be investigated and screened during the multiple manufacturing processes. Therefore, in order effectively to evaluate the fine defects, the FEM simulations were performed to make characterization in the crack detection of the bolts and the parameters such as number of turns of the coil, the coil size, applied frequency were calculated based on the simulation results. Simulations were carried out for the defect signal of eddy current probe. Exciter and receiver were utilized. In this paper, the FEM simulations were performed in both bobbin-type and pancake-type probe, both probes were optimized under Eddy current FEM simulations and the results of calculation were discussed.
해양환경 하에서 강재에 대한 방식 목적으로 Al-3%Mg 용사선재를 이용하여 아크 용사코팅을 실시하였다. 그리고 Al-3%Mg 용사코팅 층의 내식성을 개선하기 위하여 유/무기 복합 세라믹 후처리를 실시하였다. 후처리 적용에 따른 용사코팅 층의 다양한 전기화학적 실험 결과, 양극분극과 음극분극 실험 시 모든 전위구간에서 후처리 적용 시 전류밀도가 작게 나타나 내식성 개선이 확인되었다. 그리고 후처리된 용사코팅 층의 표면에서 관찰된 마이크로 크랙의 영향으로 자연전위 계측 시 심한 전위변동이 나타났으며, 양극분극 실험 시에는 후처리 층의 탈리손상이 용이하게 발생하였다. 그럼에도 불구하고 타펠분석을 기반으로 외부 환경차단 효과를 나타내는 코팅 효율이 92.11%로 산출되어 Al-3%Mg 용사코팅 층의 내식성이 향상되었다.
Lime was the solidifier mostly used at the fields of construction and civil works in the past. however, the development of Portland cement remarkably reduced the use of it. Recently as the concernment on circumstances gets higher, lime wined attention again as an eco-friendly material and was used at earth-using construction. This study examined the physical and chemical capacity of lime complexes with lime capacity improved, and performed fundamental study on the way to concretize by mixing it with earth. As a result, lime complex pressure strength was lower than cement pressure strength but it showed the possibility that its strength was improved by W/B control. The measurement of XRD after paste formation confirmed a compound generated by the reaction of Ca2+ion and Si, Al, and Fe from pozzolan reaction. A earth wall experiment by using lime complexes and earth showed that the higher, WB or the lower the quantity of unit combined materials, the lower the pressure strength was. The maximum pressure strength was maximum 11MPa when the quantity of unit combined materials was 450. It is because the composed earth particles had a high content of micro powder less than silt, so a lot of combination are demanded to secure fluidity. As a result of peptization experiment, after hardening, the material was not dissolved, which informed of the possibility of use as an outer subsidiary material. If the material is hardened by mold formation method, natural hardening crack appears. Cast expresses smart surface quality and enables to design for multiple purpose. The result shows the possibility of construction of low-story structures by using earth wall made of lime complexes and earth.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.