• 펄프종이기술
• /
• 제47권6호
• /
• pp.57-65
• /
• 2015

Microfibrillated cellulose (MFC) or Nanofibrillated cellulose (NFC) has been used to reduce the use of raw pulp and to improve paper strength. The problem of MFC preparation is high manufacturing cost. In this study, it was carried out to prepare MFC after enzyme beating and estimated properties of MFC. Endo-D was the best beating efficiency among three type of endo-glucanase. As the grinder pass number increased, the viscosity and the fines of MFC suspension increased while the crystallinity and the porosity of MFC sheet decreased. Also enzyme beating MFC was higher value in the crystallinity and lower value in the viscosity than non-enzyme MFC. In addition, the aspect ratio of MFC was the highest at 5 pass. MFC addition improved the handsheet strength and the air permeability but worsened the drainage.

• 소성∙가공
• /
• 제18권1호
• /
• pp.45-51
• /
• 2009

Shape memory alloy has been used to improve the tensile strength of composite by the occurrence of compressive residual stress in matrix using its shape memory effect. In order to fabricate shape memory alloy composite, TiNi alloy fiber and Al2024 sheets were used as reinforcing material and matrix, respectively. In this study, TiNi/Al2024 shape memory alloy composite was made by using hot press method. In order to investigate bonding condition between TiNi reinforcement and Al matrix, the micro-structure of interface was observed by using optical microscope and diffusion layer of interface was measured by using Electron Probe Micro Analyser. And the mechanical properties of composite with three parameters(volume fraction of fiber, cold rolling amount and test temperature) were obtained by tensile test. The most optimum bonding condition for fabrication the TiNi/Al2024 composite material was obtained as holding for 30min. under the pressure of 60MPa at 793K. The strength of composite material increased considerably with the volume fraction of fiber up to 7.0%. And the tensile strength of this composite increased with the reduction ratio and it also depends on the volume fraction of fiber.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2009년도 추계 학술논문 발표대회
• /
• pp.69-72
• /
• 2009

This research is focused on the applying of the foaming agent which can make the independent pore in the concrete structure in order to make a lightweight concrete structure. This lightweight foamed concrete can satisfy both the required strength and the mechanical properties as structural members. In addition, anti freezing-thawing properties also required. As a result of the unit volume-weight measurement, when the foaming agent mixed at 0.5% to 1%, the lightweight foamed concrete can be applied for the structural member. Also the density and compressive strength measurement results reveals that it will be suitable as structural member with 21MPa strength, when the density is betweenity8 to 1.9 and foaming agent quantities are 0.5% to 1%. Finally the result of freezing-thawing experiment, the effect freezing-thawing damage reduced according to adding foaming agent because those foaming agent make micro-pores in the structure which are not seen in the ordinary concrete structure.

• 한국가스학회지
• /
• 제14권6호
• /
• pp.38-43
• /
• 2010

자원 부족과 환경규제의 강화에 따라 자동차 강판재의 고강도화와 박강판화가 주요 이슈로 대두되고 있다. 그러나 고강도 강판재 사용에 있어 수소취성은 기계적 성질 저하의 문제가 되고 있다. 본 연구에서는 개발중인 590MPa급 DP강을 대상으로 조성 및 조직특성에 따른 표면층에서의 수소의 거동에 대해 연구하였다. 수소주입은 음극전기분해법을 이용하여 강제 주입시켰고, 수소주입조건에 따른 수소주입량과 표면층 조직관찰 및 미소경도시험 결과의 관계로 부터 표면층의 수소거동을 평가하였다.

• Advances in materials Research
• /
• 제9권2호
• /
• pp.99-107
• /
• 2020

Reinforced aluminum alloy base composites have become increasingly popular for engineering applications, since they usually possess several desirable properties. Recently, Warm Accumulative Roll Bonding (WARB) process has been used as a new novel process to fabricate particle reinforced metal matrix composites. In the present study, TiO₂ particles are used as reinforcement in aluminum metal matrix composites fabricated through warm accumulative roll bonding process. Firstly, the raw aluminum alloy 1060 strips with TiO₂ as reinforcement particle were roll bonded to four accumulative rolling cycles by preheating for 5 min at 300℃before each cycle. The mechanical and bonding properties of composites have been studied versus different volume contents of TiO₂ particles by tensile test, peeling test and vickers micro-hardness test. Moreover, the fracture surface and peeling surface of samples after the tensile test and peeling test have been studied versus different amount of TiO₂ volume contents by scanning electron microscopy. The results indicated that the strength and the average vickers micro-hardness of composites improved by increasing the volume content of TiO₂ particles and the amount of their elongation and bonding strength decreased significantly.

• Nuclear Engineering and Technology
• /
• 제51권6호
• /
• pp.1589-1595
• /
• 2019

In this paper, the CLAM steel strengthened by micro-scale Y-Zr-O was prepared by vacuum induction melting followed by electroslag remelting (VIM-ESR). Yttrium (Y) and zirconium (Zr) were easy to aggregates into massive yttrium-zirconium-rich inclusions in the steel melted by vacuum induction melting (VIM), which would interrupt the continuity of the matrix and reduce the mechanical properties of steel. Micron-sized Y-Zr-O inclusions would be produced with the removal of original blocky Y-Zr-rich inclusions and the submicron-sized inclusions smaller than $0.2{\mu}m$ could be retained in the steel. The small grain size and the better refinement and distribution uniformity of Y-Zr-O inclusions after remelting would be responsible for the better yield strength and toughness. For VIM-ESR alloy, the ultimate tensile strength is 749 MPa and the yield strength is 642 MPa at room temperature, meanwhile they are 391 MPa and 367 MPa at $600^{\circ}C$, respectively. Meanwhile, the ductile-brittle transition temperature (DBTT) reduced from $-43^{\circ}C$ (VIM) to $-76^{\circ}C$ (VIM-ESR).

• Membrane and Water Treatment
• /
• 제12권1호
• /
• pp.37-41
• /
• 2021

This paper presents the multiscale calculation results of the very fast volume transport in micro/nano cylindrical tubes with the wall slippage. There simultaneously occurs the adsorbed layer flow and the intermediate continuum fluid flow which are respectively on different scales. The modeled fluid is water and the tube wall is somewhat hydrophobic. The calculation shows that the power loss on the tube no more than 1.0 Watt/m can generate the wall slippage even if the fluid-tube wall interfacial shear strength is 1 MPa; The power loss on the scale 104 Watt/m produces the volume flow rate through the tube more than one hundred times higher than the classical hydrodynamic theory calculation even if the fluid-tube wall interfacial shear strength is 1 MPa. When the wall slippage occurs, the volume flow rate through the tube is in direct proportion to the power loss on the tube but in inverse proportion to the fluid-tube wall interfacial shear strength. For low interfacial shear strengths such as no more than 1 kPa, the transport in the tube appears very fast with the magnitude more than 4 orders higher than the classical calculation if the power loss on the tube is on the scale 104 Watt/m.

• Geomechanics and Engineering
• /
• 제29권6호
• /
• pp.627-643
• /
• 2022

Water-rock interactions have a significant influence on the mechanical behavior of rocks. In this study, uniaxial compression and tension tests on different water-treated sandstone samples were conducted. Acoustic emission (AE) monitoring and micro-pore structure detection were carried out. Water-rock interactions and their effects on rock mechanical behavior were discussed. The results indicate that water content significantly weakens rock mechanical strength. The sensitivity of the mechanical parameters to water treatment, from high to low, are Poisson ratio (𝜇), uniaxial tensile strength (UTS), uniaxial compressive strength (UCS), elastic modulus (E), and peak strain (𝜀). After water treatment, AE activities and the shear crack percentage are reduced, the angles between macro fractures and loading direction are minimized, the dynamic phenomenon during loading is weakened, and the failure mode changes from a mixed tensile-shear type to a tensile one. Due to the softening, lubrication, and water wedge effects in water-rock interactions, water content increases pore size, promotes crack development, and weakens micro-pore structures. Further damage of rocks in fractured and caved zones due to the water-rock interactions leads to an extra load on the adjoining coal and rock masses, which will increase the risk of dynamic disasters.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.99-102
• /
• 1999

In the study, the effect of the replacement content(20, 40, 60, 80%) and particle fineness and the chemical activator of the fly-ash on the flow and strength development of mortar was investigated. We found that the higher raito of the fly-ash replacement produced the lower the mortar strength and the higher fineness of the fly-ash yielded the higher strength. Also, we used Na2SO4 as activator of fly-ash to rise compressive strength mortar. The result as follows: the fly-ash mortar which stimulated by chemical activator, was higher strength development at early than the fly-ash mortar without chemical activator. But in the late age, the result indicated adversely.

• 국제물리치료학회지
• /
• 제8권2호
• /
• pp.1142-1145
• /
• 2017

The purpose of this study was to examine the effect of kinematic taping on respiratory muscle strength in smokers. Twenty - five university students who smoke were involved in the study. All participants were applied to kinematic taping to breathe deeply again. Subjects sit on their backs straight up and place their hands on their thighs. Tape 1 is applied from the lower prominent neck vertebrae(seven cervical vertebra) inward and downward, past shoulder blade, around ribs to the lower tip of sternum. Tape 2 extends to the lower, outer edge of shoulder blade, around ribs to the lower tip of sternum. Respiratory muscle strength was measured with Micro Mouth Pressure Measurement before and after taping. The application of kinematic taping significantly improved the inspiratory and expiratory muscle strength (p<.05). These findings suggest that kinematic taping effective in improving respiratory muscle strength and deep breathing.