• Fire Science and Engineering
• /
• v.29 no.6
• /
• pp.98-108
• /
• 2015

An integrated command system is critical for the safety of firefighters and effective work in the headquarters of a special disaster areas such as natural disaster or large man-made hazard. The integrated command system requires environmental information such as temperature, humidity, and $CO_2$ levels, as well as personal physical information such as pulse and air respirator levels. An Analog to Digital Converter (ADC) chip converts sensed information into digital signals, and a Micro Controller Unit (MCU) transmits the digital signals to a transmission board using serial communication through a Serial Peripheral Interface (SPI). The digital signals are saved in a transmission board and transmitted to the integrated command system by a Radio Frequency (RF) unit. The location of fire-fighters in a building are determined using a gyro sensor and an inertial sensor. The collected information is applied to the integrated command system for firefighter safety and to ensure that they can effectively carry out their duties. Tthis study theoretically and experimentally investigated the technologies of RF transmission, indoor position, and an integrated command system that supports decision making using the transmitted information.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.8 no.1
• /
• pp.19-25
• /
• 2011

This study presents the design of digital amplifier.controller for a proportional control valve and the development of PID discrete control scheme by using RCP(Rapid Controller Prototyping) system. RCP system is the device to embed the control code developed in PC into the microcontroller on-site. Ramp input test using the digital amplifier.controller developed in this study was carried out for the proportional control valve of domestic production and Bosch Rexroth respectively. The instability problem occurred around maximum displacement of localized valve spool at ramp input test was solved by supplementing offset current to the duty ratio of PWM(Pulse Width Modulation) driving signal to the solenoid. The comparison of test results between localized proportional control valve and Bosch Rexroth's product shows that the characteristics obtained by ramp input test and static flow gains are alike each other. Two valves are about the same in dead bands and hysteresis characteristics.

• The Magazine of the IEIE
• /
• v.29 no.1
• /
• pp.66-72
• /
• 2002

VLSI 기술의 발전은 보다 많은 양의 로직을 단일 칩에 집적 가능하게 했고, 이는 System-on-a-chip 시대의 도래를 가능하게 했다. System-on-a-chip을 가능하게 하기 위해서는 많은 종류의 IP (Intellectual Property)가 필요하고, 공정 변환을 쉽게 하기 위해서는 합성이 가능한 RTL 설계가 절실히 요구된다. 본 논문은 이러한 요구에 부응하기 위해서 hard macro 형태의 기존의 IP로 부터 합성 가능한 IP를 자동 생성해 주는 ART(Automatic RTL Translation)로 명명된 기법에 관한 것이다. 제안된 ART 기법을 이용하여 80C52 호환의 8-bit MCU(Micro-controller Unit)의 합성 가능한 RTL model을 자동 생성하였고, 개발된 Soft IP를 이용하여 TCP/IP 전용 MCU를 표함해서 다양한 제품들을 개발하였다.

• Journal of Korea Society of Industrial Information Systems
• /
• v.24 no.4
• /
• pp.9-19
• /
• 2019

As light-weight embedded devices become widely used in the area of low-power networking and high-precision sensor data acquisition, support for time-critical applications becomes essential for the light-weight embedded devices. This paper addresses the accuracy issue of a software timer for small or tiny embedded devices equiped with light-weight MCUs(Micro controller units). We first explore the characteristics of overhead in a typical implementation of a software timer, and then measure the overhead through a realistic implementation. Using the measurement result, we propose an overhead compensation technique which reduces the overhead from the hardware timer-tick.

• Journal of IKEEE
• /
• v.22 no.1
• /
• pp.93-97
• /
• 2018

In this paper, it proposes a method that uses an air pump to inject oxygen to water directly to prevent the growth of algae and cyanobacterium using MCU(Micro Controller Unit). MCU can control itself with modules of GPS, a sonic sensor, camera, conveyer belt and water pump to remove and prevent growths of algae. It can also be connected to the smart phone application software to track the system where it is and it can be controlled by the user interfaced with the smart phone application.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.4
• /
• pp.403-410
• /
• 2016

Materials made of metals have their own manifest resonant frequencies. Using this property, the quality test of products from the factory can be performed. An impact is applied to the product and the frequencies of the sound and/or vibration are measured using high-end equipments. They use a general purpose computer or a DSP(: Digital Signal Processor)-based stand-alone system which is usually too large in-size to carry and expensive to build. In this paper, we introduce a system that is developed based on a MSP430 MCU(:Micro-Controller Unit) from TI(: Texas Instruments). The ultra-low power MSP430 MCUs make it possible to make a frequency analyzer in a very small size without the need of using a large-size battery. The proposed system can be used in situations where the frequency analyzer should be carried easily with an investigator and should be built at low cost sacrificing some accuracy. We implemented the system using a launchpad supplied by TI and could confirm that the proposed system could identify with a high-accuracy the frequencies of various artificial and natural sounds.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.3
• /
• pp.567-574
• /
• 2015

In this paper, a 50ns 256-kb EEPROM IP for MCU (micro controller unit) ICs is designed. The speed of data sensing is increased in the read mode by using a proposed DB sensing circuit of differential amplifier type which uses the reference voltage, and the switching speed is also increased by reducing the total DB parasitic capacitance as a distributed DB structure is separated into eight. Also, the access time is reduced reducing a precharging time of BL in the read mode removing a 5V NMOS transistor in the conventional RD switch, and the reliability of output data can be secured by obtaining the differential voltage (${\Delta}V$) between the DB and the reference voltages as 0.2*VDD. The access time of the designed 256-kb EEPROM IP is 45.8ns and the layout size is $1571.625{\mu}m{\times}798.540{\mu}m$ based on MagnaChip's $0.18{\mu}m$ EEPROM process.

• Journal of IKEEE
• /
• v.19 no.3
• /
• pp.304-310
• /
• 2015

A SCALDO(Supercapacitor Assisted LDO) regulator is a new regulator having advantages of a SMPS(Switch Mode Power Supply) which has a good efficiency and a LDO(Low Drop-out) regulator which has stable output characteristics and good EMI(Electro Magnetic Interference) characteristics. However, a conventional SCALDO regulator needs a lot of power consumption to control its switches and it drops an efficiency of the circuit. In this paper, to reduce switching power consumption and improve an efficiency of the circuit, a new SCALDO regulator adopting MOSFETs as its switching parts is proposed and it is found out that the proposed SCALDO regulator has the maximum 9.5% higher efficiency than the conventional SCALDO regulator. We also try to simplify production process of the circuit by changing switching control method of the circuit from MCU(Micro-controller unit) based firmware control to hardware control using a comparator and a T-F/F(Flip Flop).

• Journal of Internet of Things and Convergence
• /
• v.6 no.2
• /
• pp.11-18
• /
• 2020

Since the end devices of the Internet of Things (IoT) are battery operated products, careful consideration for ultra-low power (ULP) is required. The Micro Controller Unit (MCU) industry has developed very effective functions to save energy, but developers have difficulty in selecting the MCU because various operating modes are applied to reduce energy consumption by manufacturers. Therefore, this paper introduces ULPMark benchmark, a standardized benchmark method that can compare MCUs of various vendors and feature sets, and provides hardware functions for ultra-low-power operation of the two platforms that received the high evaluation scores from ULPMark. In addition, we investigated and analyzed how developers can utilize the functions for ultra low power consumption through driver APIs and detailed register control.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.10
• /
• pp.728-737
• /
• 2019

In this study, the minimized on-board computer (OBC) module for integrated navigation is developed, which provides satellites' relative position information in formation flying and cluster operation situations. The scalability is considered to apply the user-selected wireless communication module and Global Positioning System (GPS) receiver for navigation, while considering to meet the structural design standard of nano-satellites. As a result of the product development and production, the processing speed of integrated navigation and real-time data synchronization is satisfied for cluster operation nano-satellites by using micro controller unit (MCU). From a heat/vacuum, vibration and radiation test, the OBC was confirmed to be operated in space environments. From these results, a mass production system of OBC was made which is a key part of development on satellite formation flying and cluster/constellation missions that the community demands are increasing.