• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.24 no.2
• /
• pp.238-245
• /
• 2014

Objectives: It was known that workers in synthetic leather company are mainly co-exposed to dimethylformamide(DMF) with methyl ethyl ketone(MEK) or toluene(TOL) instead of a single dimethylformamide. This study was examined to the physico-chemical properties in single DMF and binary mixture DMF with MEK or TOL. Materials: Physico-chemical properties were measured by Korean and American Standard Test Methods. Results: Boiling point, specific gravity and flash point in single DMF were significantly higher than binary mixture DMF with MEK or TOL and such difference was dependent on the mixing ratio of MEK and TOL, and low explosion limit in binary mixture DMF with TOL was only significantly lower than single DMF. However, Reid vapor pressure had significantly higher in binary mixture DMF with MEK or TOL compared with single DMF. Conclusions: Our results demonstrate that the binary mixture DMF with MEK or TOL synergistically increases volatilization of DMF. It was concluded that the interaction between DMF and MEK and/or TOL might play a key role in the volatilization process of DMF under environmental conditions of workplace.

• Journal of Environmental Science International
• /
• v.20 no.4
• /
• pp.501-509
• /
• 2011

Unlike many laboratory-scale studies on absorption of organic compounds (VOCs), limited pilot-scale studies have been reported. Accordingly, the present study was carried out to examine operation parameters for the effective control of a hydrophilic VOC (methyl ethyl ketone, MEK) by applying a circular pilot-scale packed-absorption system (inside diameter 37 cm ${\times}$ height 167 cm). The absorption efficiencies of MEK were investigated for three major operation parameters: input concentration, water flow rate, and ratio of gas flow-rate to washing water amount (water-to-gas ratio). The experimental set-up comprised of the flow control system, generation system, recirculation system, packed-absorption system, and outlet system. For three MEK input concentrations (300, 350, and 750 ppm), absorption efficiencies approached near 95% and then, decreased gradually as the operation time increased, thereby suggesting a non-steady state condition. Under these conditions, higher absorption efficiencies were shown for lower input concentration conditions, which were consistent with those of laboratory-scale studies. However, a steady state condition occurred for two input concentration conditions (100 and 200 ppm), and the difference in absorption efficiencies between these two conditions were insignificant. As supported by an established gas-liquid absorption theory, a higher water flow rate exhibited a greater absorption efficiency. Moreover, as same with the laboratory-scale studies, the absorption efficiencies increased as water-to-gas ratios increased. Meanwhile, regardless of water flow rates or water-to-gas ratios, as the operation time of the absorption became longer, the pH of water increased, but the elevation extent was not substantial (maximum pH difference, 1.1).

• Bulletin of the Korean Chemical Society
• /
• v.35 no.12
• /
• pp.3637-3641
• /
• 2014

In this study, we analyzed the toxicity of mixtures of dimethylformamide (DMF) and methyl ethyl ketone (MEK) or DMF and toluene (TOL) and predicted their toxicity using quantitative structure-activity relationships (QSAR). A QSAR model for single substances and mixtures was analyzed using multiple linear regression (MLR) by taking into account the statistical parameters between the observed and predicted $EC_{50}$. After preprocessing, the best subsets of descriptors in the learning methods were determined using a 5-fold cross-validation method. Significant differences in physico-chemical properties such as boiling point (BP), specific gravity (SG), Reid vapor pressure (rVP), flash point (FP), low explosion limit (LEL), and octanol/water partition coefficient (Pow) were observed between the single substances and the mixtures. The $EC_{50}$ of the mixture of DMF and TOL was significantly lower than that of DMF. The mixture toxicity was directly related to the mixing ratio of TOL and MEK (MLR $EC_{50}$ equation = $1.76997-1.12249{\times}TOL+1.21045{\times}MEK$), as well as to SG, VP, and LEL (MLR equation $EC_{50}=15.44388-19.84549{\times}SG+0.05091{\times}VP+1.85846{\times}LEL$). These results show that QSAR-based models can be used to quantitatively predict the toxicity of mixtures used in manufacturing industries.

• Journal of the Korean Magnetics Society
• /
• v.6 no.4
• /
• pp.251-257
• /
• 1996

A coercivity of barium ferrite (BaM) tape was found to be higher than the coercivity of BaM powder, This difference is in the range of 50 Oe to 600 Oe, which depends on substituted cations. physical properties of powder, and preparation conditions of the tape. The coercivity difference is attributed to both particle stacking and adsorption of organic solvent on particle surface. Regardless of substituted cations, the coercivity of longitudinally oriented BaFe tape was higher than that of BaM powder by a range of 100 Oe to 120 Oe, which is caused by particle stacking' During the active adsorption process on preparation of magnetic paint, where MEK (methyl ethyl ketone), TOL (toluene) and CHO (cyclohexanone) were used, chemisorption of solvents on the surface of substituted BaFe particle occurred to form polymeric compounds surrounding the particle. An increase in coercivity, caused by the solvent adsorption, was significant for Co-substutited BaM tape. Among these solvents CHO was the most effective one in increasing the coercivity of the Co-Ti substituted BaM tape.

• Journal of Radiation Protection and Research
• /
• v.9 no.2
• /
• pp.103-111
• /
• 1984

A convenient method of $^{99m}Tc$-methyl-ethyl-ketone (MEK) extraction technique was developed and a mobile $^{99m}Tc$-extraction generator was designed. The MEK extraction and the phase separation of $^{99m}TcO^-{_4}$ were carried out with a simple procedure in the same container. The shielding of $^{99}Mo$ radioactivity was made with one lead container. The system was simplified by shielding $^{99m}TcO_4{^-}({\gamma}_e=0.14\;MeV)$ separately. $^{99m}TcO^-{_4}\;in\;^{99m}Tc-MEK$ extract was recovered by adsorption and elution only, and therefore, the possibility of volatilization was reduced. The volume of $^{99m}TcO^{-}{_4}$-saline product was reduced to 1 ml by using a small alumina column and the column operation time was shortened. The separation time of $^{99m}Tc$ was reduced to 30 minutes, and the operation was carried out at the outside of the shielding. The system was designed to operate under the condition of bacteria-free.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.15 no.3
• /
• pp.261-269
• /
• 2005

To investigate the field applicability of a diffusive sampler (3M OVM #3500, passive sampling method) authors conducted a simultaneous measurement of personal organic solvents exposure in the air of the workplaces by charcoal tube with low volume sampler (active sampling method) and diffusive sampler. Samples were collected and analyzed by NIOSH method ($NMAM^{(R)}$) from thirty-eight workers in 12 factories who work in 6 different processes. Geometric mean (GM) and geometric standard deviation (GSD) were used to describe the result. To compare the results of the two methods, paired t-test was used. According to the manual of the exposure assessment of the mixed organic solvents (Ministry of Labor, Korea), Em was calculated. Simple linear regression was used to evaluate the relationship between the two methods. Results were as follows; 1. Eight different solvents (ethyl acetate, n-hexane, toluene, xylene, acetone, isopropyl alcohol, methyl ethyl ketone (MEK), and methyl isobutyl ketone) were detected simultaneously in the two methods and the concentrations of the personal exposure were lower than 0.5 TLV level. The concentration of the charcoal tube method was higher than that of a diffusive sampler in n-hexane and MEK (p<0.05). 2. Em of the charcoal tube method was higher than that of diffusive sampler method but not significantly different and was lower than the OEL (Occupational Exposure Limit) in all 6 processes. 3. There was a significant correlation between the two methods in low concentrations of the 8 organic solvents (p<0.05). In conclusion, there was no difference in charcoal tube method and diffusive sampler method in low concentrations of some organic solvents, diffusive sampler can be applied to assess the personal monitoring in low level exposure.

• Applied Chemistry for Engineering
• /
• v.7 no.6
• /
• pp.1053-1060
• /
• 1996

$\beta$-ketohexanal as a chelating extractant was synthesized from the reaction of ethyl formate and methyl propyl ketone in the presence of sodium amide, and the equilibrium characteristics in the extraction of copper by $\beta$-ketohexanal-chloroform were investigated. The equilibrium constants such as the dissociation constant and the partition coefficients of $\beta$-ketohexanal, the stability constant and the partition coefficient of copper chelating complex, and the overall equilibrium constant in the extraction of copper were determined by spectrophotometric measurements, and the mechanism of extraction was proposed. The percent of extracted copper by $\beta$-ketohexanal-chloroform was near 100%, and the selective extraction of copper from Cu-Zn-Cd mixture was possible. Copper was found to be extracted as $CuR_2$ and the equilibrium reaction was expressed as $Cu^{2+}+2{\overline{HR}}{\rightleftarrows}{\overline{CuR{_2}}}+2H^+$.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.6
• /
• pp.31-37
• /
• 2010

In this study, optimization of MEK and Toluene removal was conducted by HTO(Hybrid Thermal Oxidation) system. HTO system has a multi-bed reaction plate and the plate consisted of wasted heat regeneration part and catalysis part. VOCs removal by HTO system was estimated by changing inlet flow rates with different valve changing times. Under $350^{\circ}C$ of combustion temperature, VOCs was fully converted and the equivalent conversion was 100%. The thermal oxidation efficiency, related to the amount of injected fuel into HTO system and the valve change time, was revealed at the level of 93.0~96.3%. In case of MEK removal by HTO system, the efficiency was ranged from 91.1 to 97.1%. Also, Toluene removal efficiency(93.2~97.4%) was good and stable with respect to the operating conditions. Considering above results, it was proved that HTO system could be a stable and compact system for VOCs, especially MEK and Toluene with high removal efficiency.

• Journal of Environmental Health Sciences
• /
• v.45 no.5
• /
• pp.465-473
• /
• 2019

Objectives: A variety of industries handling hazardous chemicals emit odorous substances. Based on the emission characteristics of major odor substances from the results of hazardous chemical substance emissions, we will define basic data for improving the management methods of odorous substances. Methods: A survey of hazardous pollutant emissions for 2010-2016 was conducted through the Pollutant Release and Transfer Register homepage. Eight kinds of designated odor substances (ammonia, hydrogen sulfide, dimethyl disulfide, acetaldehyde, styrene, toluene, xylene, methyl ethyl ketone) provided the study subjects. The status of chemical accidents for the target substances was analyzed using the Chemistry Safety Clearing-house system. Results: From 2010 to 2016, it was found that more than 30% of businesses that emitted odorous substances accounted for more than 50% of the total emissions of the eight substances. Emissions of xylene, toluene, methyl ethyl ketone, and ammonia were found, in that order, and they made up more than 90% of the total emitted. By region, about 70% of odorous substances were emitted in the top-four regions: Gyeongsangnam-do Province, Ulsan, Gyeonggi-do Province, and Jeollanam-do Province. Conclusion: Recently, the amount of chemical emissions has been continuously increasing, including those that can cause odor. Odorous substances can be a serious risk to the lives of local residents. Systematic research is needed for the health protection of residents.

• Journal of the Korean Society of Urban Environment
• /
• v.18 no.4
• /
• pp.503-509
• /
• 2018

In this study, a Proton-Transfer Reaction-Time-of-Flight Mass spectrometer (PTR-TOF-MS) was used for the continuous monitoring of Volatile Organic Compounds (VOCs) emitted from semiconductor workplace such as photolithography (PHOTO), flat panel display (FPD), organic light emitting diode (OLED), etching (WET) process. The averaged VOCs mixing ratio in the such workplace, PHOTO was 6.5 ppm, FPH was 6.4 ppm, WET was 2.0 ppm and OLED was 1.3 ppm, respectively. The abundance of VOCs in the workplace were methyl ethyl ketone (MEK) with 2.8 ppm (69%) and acetaldehyde with 0.5 ppm (13.2%). Depending on the semiconductor process characteristics, various VOCs have been observed in the workplace. The VOCs mixing ratio are lower than the workplace regulation standard (TWA), it is necessary to continuously monitor and effectively manage these VOCs.