• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.6
• /
• pp.923-926
• /
• 2017

In this study, a novel wideband conformal thin antenna is presented for endoscopic capsule application at the 915 MHz Industrial, Scientific and Medical (ISM) band. The thickness of the antenna is only 0.2 mm which can be wrapped inside a capsule's inner wall. By cutting meandered slots on patch, open end slots on ground and utilizing long arm, the proposed antenna can obtain significant size reduction. The net volume of the proposed antenna including substrate and superstrate is only $37.4mm^3$ ($187mm^2$ surface area). This conformal antenna has shown good performance through simulation and measurement with maximum gain of -23 dBi and wide bandwidth from 137 MHz - 205 MHz depending on different environment. In addition, the effect of internal materials specially metallic battery is discussed briefly.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.2
• /
• pp.5-12
• /
• 2000

Uncooled metallic thin-film thermopile infrared detectors have been fabricated, and the figures of merit for the detectors were examined. The hot junctions of a thermopile were prepared on a $Si_{3}N_{4}/SiO_{2}/Si_{3}N_{4}$-membrane which acts as a thermal isolation layer, the cold junctions on the membrane supported with the silicon rim which functions as a heat sink, and Au-black was used as an infrared absorber. Infrared absorbance of Au-black, which strongly depends on the chamber pressure during Au-evaporation and its mass per area, was found to be about 90 ％ in the wavelength range from 3${\mu}{\textrm}{m}$ to 14${\mu}{\textrm}{m}$. Voltage responsivity, noise equivalent power, and specific detectivity of Bi-Sb thermopile infrared detector at 5 Hz-chopping frequency were about 10.5V/W, 2.3 nW/Hz$^{1/2}$, 및 $1.9\times10^{7}$ cm.Hz$^{1/2}$/w at room temperature in air, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.12
• /
• pp.2427-2433
• /
• 2015

A high-gain circularly-polarized patch antenna with a double-layered superstrate is proposed operating at a wireless LAN frequency. A superstrate has an array of metallic periodic unit cells and is located above the patch antenna with an air-gap. The designed antenna has a high gain of over 9.59dBi, which is the gain enhancement of 6.48dB compared to the patch antenna without superstrate. And it has a low axial ratio of under 3dB, so that it maintains the circular polarization of the patch antenna. The optimum air-gap height at the superstrate of $4{\times}4$ arrays is 25mm, which is equivalent to about $0.2{\lambda}$ at the frequency of 2.45GHz. We confirmed that the double-layered stacking of a superstrate increases the effective aperture size and hence it leads to enhance a gain of the patch antenna.

• Journal of the Korean Society of Safety
• /
• v.29 no.6
• /
• pp.9-14
• /
• 2014

Recently many efforts and researches have been done to cope with industrial facilities that require a low energy machines due to the gradual depletion of the natural resources. The fiber-reinforced composite materials in general have good properties and have the proper mechanical properties according to the change of the ply sequences and fiber distribution types. However, in the fiber-reinforced composite material, there are several problems, including fiber breaking, peeling, layer lamination, fiber cracking that can not be seen from the metallic material. Particularly, the fracture and delamination are likely to be affected by the thickness of the stacking laminates when the bi-material laminated structure is subjected to a load of the mixed mode. In this study, we investigated the effect of the thickness ratio of the difference in the CFRP/GFRP bi-material laminate composites by measuring the cracking behavior and the AE characteristics in a mixed mode loading, which may be generated in the actual structure. The results show that the thickness of the CFRP becomes more thick, the mode I energy release rate becomes a larger, and also the influence of mode I is greater than that of mode II. In addition, AE amplitude which shows the level of the damage in the structure was obtained the more damage in the CFRP with the thin thickness.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.12
• /
• pp.1402-1409
• /
• 2008

In this paper, a low temperature co-fired ceramic cavity backed antenna in order to improve the performances of radiation and bandwidth for the antenna with high relative dielectric constant is proposed. Low temperature co-fired ceramic cavity consisted of several ground planes with closely spaced metallic vias connected. It is shown that the size of a low temperature co-fired ceramic cavity has the effects on the performances of radiation and bandwidth for the antenna. The proposed 2x4 low temperature co-fired ceramic cavity backed antenna is $10{\times}20\;mm^2$ in size. Measured results show antenna gain of $11.8{\sim}14.1\;dBi$ and bandwidth of 13 %(7.9 GHz) in the $57{\sim}64\;GHz$ band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.4
• /
• pp.342-349
• /
• 2016

We design a displaced-axis Gregorian dual antenna in the form of a metal reflectarray antenna for millimeter wave region, W-band. Unlike a reflectarray composed of printed patch antennas on a dielectric substrate, metallic rectangular waveguide unit-cells are proposed to avoid the loss of substrate and take an advantage of ease of typical metal machining fabrication. In this paper, the radiation characteristics of constructed metal reflectarray antennas show ultra high-gain antenna over 50 dBi at a target frequency in W-band. The experimental measurements are conducted in millimeter-wave compact range antenna measurement system.

• Tribology and Lubricants
• /
• v.38 no.6
• /
• pp.235-240
• /
• 2022

Atomically-thin 2D nanomaterials can be easily deformed and have surface corrugations which can influence the frictional characteristics of the 2D nanomaterials. Chemical vapor deposition (CVD) graphene can be grown in a wafer scale, which is suitable as a large-area surface coating film. The CVD growth involves cooling process to room temperature, and the thermal expansion coefficients mismatch between graphene and the metallic substrate induces a compressive strain in graphene, resulting in the surface corrugations such as wrinkles and atomic ripples. Such corrugations can induce the friction anisotropy of graphene, and therefore, accurate imaging of the surface corrugation is significant for better understanding about the friction anisotropy of CVD graphene. In this work, the combinatorial analysis using friction force microscopy (FFM) and transverse shear microscopy (TSM) was implemented to unveil the friction anisotropy of CVD bi-layer graphene. The periodic friction anisotropy of the wrinkles was measured following a sinusoidal curve depending on the angles between the wrinkles and the scanning tip, and the two domains were observed to have the different friction signals due to the different directions of the atomic ripples, which was confirmed by the high-resolution FFM and TSM imaging. In addition, we revealed that the atomic ripples can be easily suppressed by ironing the surface during AFM scans with an appropriate normal force. This work demonstrates that the friction anisotropy of CVD bilayer graphene is well-correlated with the corrugated structures and the local friction anisotropy induced by the atomic ripples can be controllably removed by simple AFM scans.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.55-55
• /
• 2010

We use ab initio density functional theory to determine the effect of bundling on the equilibrium structure, electronic and magnetic properties of $Mo_6S_{9-x}I_x$nanowires with x = 0, 3, 4.5, 6. Each unit cell of these systems contains two $Mo_6S_{6-x}I_x$ clusters connected by S3 linkages to form an ordered linear array. Due to the bi-stability of the sulfur linkages, the total energy of the nanowires exhibits typically many minima as a function of the wire length. We find that nanowires can switch over from metallic to semiconducting by applying axial stress. Structural order is expected in bundles with x=0 and x=6, since there is no disorder in the decoration of the Mo clusters. In bundles with other stoichiometries, we expect structural disorder to occur. We find the optimum inter-wire distance to depend sensitively on the orientation of the wires, but only weakly on x. It is also found that the electronic properties of nanowires are affected strongly due to bundling of nanowires exhibiting very unusual Fermi surfaces. Furthermore, ferromagnetic behaviors are observed in selected stable and many more unstable atomic arrangements in nanowire bundles.

• Economic and Environmental Geology
• /
• v.48 no.1
• /
• pp.1-13
• /
• 2015

The geology of the Seungryung Zn deposit, located in the Muzu basin, consists of Precambrian leucocratic granitic gneiss, Cretaceous clastic rocks, pyroclastic rocks, and intrusive rocks. The deposit shows a weakly skarnized hydrothermal replacement ore developed along limestone bed in the gneiss. The mineralization can be divided into three stages: the early skarnization producing garnet and pyroxene, the main mineralization in the middle stage precipitating most metallic minerals such as magnetite, sphalerite, chalcopyrite, pyrrhotite, Pb-Ag-Bi-S system minerals, and the late stage for altered or low temperature minerals such as chlorite and marcasite. Pb-Ag-Bi-S system minerals include heyrovskite-eskimoite solid solution, lillianite-gustavite solid solution, and vikingite. Chalcopyrite diseases are quite common in sphalerite showing bead chains and dusting textures. The ${\delta}^{34}S$ values of sulfides minerals are concentrated within the narrow range of 3.4~4.1‰ for pyrite, 3.3~4.3‰ for sphalerite, 4.0~4.3‰ for chalcopyrite, and 2.8‰ for galena, suggesting that most sulfur is of igneous origin. Sulfur isotope geothermometry is calculated to be $346{\sim}431^{\circ}C$, implying that the mineralization occurred at relatively high temperature. FeS contents of sphalerite are relatively high in the range of 6.58~20.16 mole% (avg. 16.58 mole%) with the enrichment of Mn compared to Cd, similarly to representative skarn Pb-Zn deposits in South Korea. On the contrary, sphalerite from Au-Ag deposits in the Seolcheon mineralized zone around the Seungryung deposit is enriched in Cd, showing similar feature like representative epithermal Au-Ag deposits. This suggests that around the related igneous rocks, magnetite and sphalerite were produced at high temperature in the Seungryung deposit, and with decreasing temperature and compositional change of mineralizing fluids, Au-Ag mineralization proceeded in the Seolcheon mineralized zone.

• Clean Technology
• /
• v.21 no.2
• /
• pp.85-89
• /
• 2015

Utilized in a variety of electronic components, electronic components industry with metallic ink technology was established itself as a major technology research and development was gradually increasing, silver ink that is excellent in conductivity and stability, have long been used in the industry of electronic components in recent years and silver ink has been the size of nanoscale particles dispersed by developing display, an electronic tag, a flexible circuit board or the like used in the semiconductor and electronics as has been highlighted in, however industry modernization of equipment by increasing the production and consumption of products generated during the production process and environmental pollutants by use of waste products is expected to bring a serious environmental problem. In this study, prepared by a wet reduction method, the manufacturing process of the silver nano-ink to the entire process of the environmental impact assessment (LCA) was evaluated using the techniques. Life cycle assessment software GaBi 6 was used as received from the relevant agencies of the silver nano-ink data with reference to the manufacturing process, building inventory was international organization for standardization (ISO) 14040, 14044 compliant LCA conducted over four stages.