• 한국해양공학회지
• /
• 제13권1호통권31호
• /
• pp.29-38
• /
• 1999

In this paper the forming simulation of circular bulge by using PAM-STAMP has been performed to estimate the sheet metal forning and the plastic deformation characteristic of circular bulge. The uniaxial tension tests adn bulge tests are carried out for studying the forming characteristics of materials, and also Moire experiment are carried out for measuring the radius of curvature of the bulge and the polar compressive thickness strain. In order to compare the simulation results with the experiment and Hills theory, the relationships between redius of curvature adn polar height of the bulge, between hydraulic pressure and polar height, and between polar compressive thickness strain and polar height, are used. According to this study, the results of simulation and Hills theory are good agreement to the experiment. So, the results of simulation by using PAM-STAMP and Hills theory will give engineers good information to assess the formagbility and plastic deformation characteristic of hydraulic circular bulge test.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.635-636
• /
• 2013

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.375-375
• /
• 2001

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.84-87
• /
• 2009

This paper describes a novel method for fabricating large area metallic stamp with high aspect ratio micro intaglio features. Micro machined brass master with pillar and larger width groove patterns were electroformed to form inverse structures on the large area metallic stamp. This enabled large area metallic stamp with fine micro high aspect ratio micro intaglio features which were small width groove patterns and quadrilateral hole patterns that cannot be fabricated by direct micro machining process. Fabricated large area metallic stamp with high aspect ratio micro intaglio features was measured and analyzed.

• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.999-1005
• /
• 2004

A new stamp fabrication technique for the soft lithography has been developed in the range of several microns by means of a nano-replication printing (nRP) process. In the nRP process, a figure or a pattern can be replicated directly from a two-tone bitmap figure with nano-scale details. A photopolymerizable resin was polymerized by the two-photon absorption which was induced by a femtosecond laser. After the polymerization of master patterns, a gold metal layer (about 30 ㎚ thickness) was deposited on the fabricated master patterns for the purpose of preventing a join between the patterns and the PDMS, then the master patterns were transferred in order to fabricate a stamp by using the PDMS (poly-dimethylsiloxane). In the transferring process, a few of gold particles, which were isolated from the master patterns, remained on the PDMS stamp. A gold selective etchant, the potassium iodine (KI) was employed to remove the needless gold particles without any damage to the PDMS stamp. Through this work, the effectiveness of the nRP process with the PDMS molding was evaluated to make the PDMS stamp with the resolution of around 200 ㎚.

• 한국재료학회지
• /
• 제15권9호
• /
• pp.589-593
• /
• 2005

Nanoimprinting lithography (NIL) is known as a suitable technique for fabricating nano and micro structures of high definition. Hot embossing is one of NIL techniques and can imprint on thin films and bulk polymers. Key issues of hot embossing are time and expense needed to produce a stamp withstanding a high temperature and pressure. Fabrication of a metal stamp such as an electroplated nickel is cost intensive and time consuming. A ceramic stamp made by silicon is easy to break when the pressure is applied. In this paper, a plastic stamp using a high temperature epoxy was fabricated and tested. The plastic stamp was relatively inexpensive, rapid to produce and durable enough to withstanding multiple hot embossing cycles. The merits of low viscosity epoxy solutions were a fast degassing and a rapid filling the microstructures. The hot embossing process with plastic stamp was performed on PMMA substrates. The hot embossing was conducted at 12.6 bar, $120^{\circ}C$ and 10 minutes. An imprinted PMMA wafer was almost same value of the plastic stamp after 10 times embossing. Entire fabrication process from silicon master to plastic stamp was completed within 12 hours.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1511-1513
• /
• 2005

The polymer-light emtting diodes(PLEDs) were comprised a design of OLED array, process develop by using ITO thin glass, and fabrication of PDMS stamp by using nanocontact printing. In the study, we describe a different approach for building OLEDs, which is based on physical lamination of thin metal electrodes supported by a PDMS stamp layer against an electroluminescent organic. We develop that devices fabricated in this manner have better performance than those constructed with standard processing techniques. The lamination approach avoids forms of disruption that can be introduced at the electrode organic interface by metal evaporation and has a reduced sensitivity to pinhole or partial pinhole defects. Also, it is easy to build patterned PLED with feature sizes into the nanometer regime. This method provides a new route to PLED for applications ranging from high performance displays to storage and lithography systems, and PLED can used for organic electronics and flexible display.

• 한국정밀공학회지
• /
• 제21권6호
• /
• pp.153-159
• /
• 2004

In this study, a new process to pattern directly on a thin metal layer using improved nano replication printing (nRP) process is suggested to evaluate the possibilities of fabricating a stamp for nano-imprinting. In the nRP process, any figure can be replicated from a bitmap figure file in the range of several micrometers with nano-scaled details. In the process, liquid-state resins are polymerized by two-photon absorption which is induced by femto-second laser. A thin gold layer was sputtered on a glass plate and then, designed patterns or figures were developed on the gold layer by newly developed top-down building approach. Generally, stamps fur nano-imprinting have been fabricated by using the costly electron-beam lithography process combined with a reactive ion-etching process. Through this study, the effectiveness of the improved nRP process is evaluated to make a stamp with the resolution of around 200nm with reduced cost.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.53.1-56
• /
• 1999

Using a new dynamic-explicity program SAIT_STAMP the analysis of forming a front door panel is presented. The analysis consists of 7 processes including drawing trimming flanging and springback. From the analysis results it is shown that adaptive refinement scheme and robust trimming algorithm enable SAIT_STAMP to simulate the multi-stage forming of automotive parts with large and complex geometry.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 금형가공 심포지엄
• /
• pp.19-27
• /
• 1998

박판금속성형공정을 통하여 컴퓨터를 이용한 계산방법으로 효율적이고 정확하게 해석할 수 있는 박판성형해석시스템인 SAIT_STAMP를 개발하였다. 또한 이를 현업문제에 적용하여 금형의 개발기간과 비용을 줄이고 성형품 품질저하 문제들을 해결하는데 이용하였다. SAIT_STAMP 는 성형해석, 성형후해석 프로그램과 전·후 처리기로 구성이 되어있다. 금형과 재료의 접촉 및 마찰을 고려한 새로운 접촉처리방법을 성형해석에 적용하여 해석속도와 해석정확도를 향상하였고 다단계성형 및 유압성형 등 박판성형에 필요한 대부분의 기능을 개발하여 적용하였다. 성형후해석은 성형해석의 결과를 토대로 스프링백해석을 수행한다. Visual C++을 사용하여 개발된 전·후 처리기는 window 95N/T 환경의 PC에서 수행된다. 개발된 프로그램을 이용하여 현업 문제에 적용 해석하였으며 상용S/W 대비 우수한 결과를 얻었다. 현재 삼성내 9개 관계사에서 설치되어 사용중이며 프로그램의 대외신뢰성확보를 위해 대학과 비경쟁업체에 프로그램을 설치하여 프로그램을 설치하여 프로그램의 시험과 성능향상을 하고 있다.