• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.4
• /
• pp.347-353
• /
• 2010

Source terms of metal waste comprising a spent fuel assembly are relatively important when the spent fuel is pyroprocessed, because cesium, strontium, and transuranics are not a concern any more in the aspect of source term of permanent disposal. In this study, characteristics of radiation source terms for each structural component in spent fuel assembly was analyzed by using ORIGEN-S with a assumption that 10 metric tons of uranium is pyroprocessed. At first, mass and volume for each structural component of the fuel assembly were calculated in detail. Activation cross section library was generated by using KENO-VI/ORIGEN-S module for top-end piece and bottom-end piece, because those are located at outer core with different neutron spectrum compared to that of inner core. As a result, values of radioactivity, decay heat, and hazard index were reveled to be $1.40{\times}10^{15}$ Bequerels, 236 Watts, $4.34{\times}10^9m^3$-water, respectively, at 10 years after discharge. Those values correspond to 0.7 %, 1.1 %, 0.1 %, respectively, compared to that of spent fuel. Inconel 718 grid plate was shown to be the most important component in the all aspects of radioactivity, decay heat, and hazard index although the mass occupies only 1 % of the total. It was also shown that if the Inconel 718 grid plate is managed separately, the radioactivity and hazard index of metal waste could be decreased to 20~45 % and 30~45 %, respectively. As a whole, decay heat of metal waste was shown to be negligible in the aspect of disposal system design, while the radioactivity and hazard index are important.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.740-743
• /
• 2008

본 연구에서는 MicroTec을 이용하여 MOSFET Process 설계를 구현하였다. MOS(Metal Oxide Semiconductor)는 실리콘 기판 등의 반도체 표면에 산화막을 입히고 그 위에 금속을 부착시킨 구조이다. MOSFET의 응용은 VLSI 회로에만 제한되지 않고 전력-전자 회로에서 중요한 역할을 하며 점점 더 적용범위를 증가시켜 마이크로파 응용에 이르기까지 광범위하게 사용하고 있다. Process를 구연하는 방법은 Grid의 크기를 지정하고, 기판의 원소는 B로 지정하고 $1{\times}10^{15}/cm^3$ 만큼 도핑한다. 기판에 구멍을 내어 B와 As의 도핑농도와 에너지값을 설정한다. 마지막으로 어넬링 파라미터 값을 설정한다. 본 연구에서는 원소의 도핑값과 에너지값의 변화에 따른 MOSFET Process의 변화를 알 수 있었다.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.11
• /
• pp.975-979
• /
• 2014

Transparent conductive films (TCF) with excellent electrical properties and high mechanical flexibility have been widely studied because of their potential for application in optoelectronic devices such as light-emitting diodes, paper displays and organic solar cells. In this paper, we report on low-resistance and high-transparent TCF for flexible device applications. To fabricate a high-resolution roll imprinted TCF, the following steps were performed: the design and manufacture of an electroforming stamp mold, the fabrication of high-resolution roll imprinted on flexible film, the manufacture of Ag-nano paste which was filled into patterned film using a doctor blade process. Also, we was demonstrated with the successful application(ITO free organic photovoltaic) of the developed flexible TCF.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.214-214
• /
• 2009

While critical properties of BSCCO wires rely considerably on grid direction upon BSCCO and have very complicated mechanism of generating a superconducting phase, making it difficult to improve properties of wires, YBCO thin-film wires which can be formed in a superconducting phase upon metal board through vapor deposition processing can get excellent direction and reduce manufacturing costs with more flexibility in improving critical properties; thus, they will be suitable for instrument application in the future. Contrary to BSCCO wires for which thick silver alloy covering materials should inevitably be used, moreover, YBCO thin-film wires have an advantage of making thickness and quality of covering materials different by usage. Such a property can be an important element to widen application of wires by presenting possibility of using thin-film wires as superconducting material for fault current limiter as well as for high power current application. In this study we intend to prepare YBCO thin-film wires with different stabilizer layers to analyze current application and current restriction properties by stabilizer layers on the basis of detailed researches on changes in current classification properties below critical value.

• Journal of Korean Society for Atmospheric Environment
• /
• v.13 no.6
• /
• pp.463-474
• /
• 1997

Metallic elements in dustfall have been known as notable air pollutants directly or indirectly influencing human health and wealth. The first aim of this study was to obtain precise spatial distribution patterns of 5 elements (Pb, Zn, K, Cr, and Al) in dustfall around Suwon area. To predict isometric lines of metal fluxes deposited on unsupervised random sites, the study has applied both spatial statistics as a receptor model and a GIS (geographic information system). Total of 31 sampling sites were selected in the study area (roughly 3 by 3 km grid basis) and dustfall samples were then collected monthly basis by the British deposit gauges from Dec., 1995 to Nov., 1996. The metallic elements in the dustfall were then analyzed by an atomic absorption spectrometer (AAS). On the other hand, a base map overlapped by 7 layers was constructed by using the AutoCAD R13 and ARC/INFO 3.4D. Four different spatial interpolation and expolation techniques such as IDW (inverse distance weighted averaging), TIN (triangulated irregular network), polynomial regression, and kriging technique were examined to compare spatial distribution patterns. Each pattern obtained by each technique was substantally different as varing pollutant types, land of use types, and topological conditions, etc. Thus, our study focused intensively on uncertainty analysis based on a concept of the jackknife and the sum of error distance. It was found that a kriging technique was the best applicalbe in this study area.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.5
• /
• pp.102-107
• /
• 2012

Halogen lamp was applied to fabricate the selective emitter crystalline silicon solar cell. In selective emitter structure, the recombination of minority carriers is reduced with heavily doped emitter under metal grid, consequently improving the conversion efficiency. Laser selective emitter process which is recently used the most generally induces the damage on the silicon surface. However the lamp has enough heat to form heavily doped emitter layer by diffusing phosphorus from PSG without surface damage. In this work, we have studied to find the design and the suitable condition for halogen lamp such as power, time, temperature and figured out the possibility to fabricate the selective emitter silicon solar cell by lamp heating. The sheet resistance with $100{\Omega}/{\Box}$ was lower to $50{\Omega}/{\Box}$ after halogen lamp treatment. Heat transfer to lightly doped emitter region was blocked by using the shadow mask.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.1
• /
• pp.76.1-76.1
• /
• 2016

During the last decade, high-resolution spectra of many very metal-poor (VMP) stars have been observed and their surface compositions have been measured. The abundance patterns of the VMP stars strongly constrain the nucleosynthesis of Pop III stars because they born from material enriched by supernovae or wind ejecta of Pop III stars. The observations show overabundances of light elements like C, N, O, Na, Mg and Al and very low $C^{12}/C^{13}$ ratios. These results indicate that mixing between the H-burning and He-burning region occurred in Pop III stars. To explain these observational results, we performed 1D stellar evolution simulations for non-rotating Pop III stars with ZAMS masses ranging from $20M_{\Box}$ to $50M_{\Box}$ and various overshooting parameters. In our grid calculation, convective mixing between helium burning layers and the hydrogen burning shell generally occurred in models with masses less than $40M_{\Box}$ without rotation and these models show an excess of light element abundances. From this result, it is expected that we could explain the observed abundance patterns with convective mixing in non-rotating massive Pop III stars and we do not necessarily have to invoke rotational mixing.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.1
• /
• pp.34-46
• /
• 2004

Copper films were prepared by using ECR-MOCVD(Electron Cyclotron Resonance Metal Organic Chemical Vapor Deposition) coupled with a DC bias system. The DC bias is connected to the electrode which placed 1∼3cm above the polymer substrate. The pulse electrical field around the electrode attracts the positive charged copper ions generated from the dissociation of copper precursor, $Cu(hfac)_2$, under ECR plasma. Condensation of supersaturated copper ions in the space between the electrode and substrate, makes it possible to deposit copper film on the polymer substrate even at room temperature. In this study, optimization of the electrode configuration was carried out in order to obtain the uniform films. The uniformity of the deposited films were closely related to the parameters of electrode geometry such as electrode shape, thickness, grid size and the spacing between electrodes. The most uniform copper film was observed with the electrode that enabled uniform electrical field distribution across the whole dimension of electrode.

• Nuclear Engineering and Technology
• /
• v.41 no.6
• /
• pp.797-806
• /
• 2009

The Multichannel Analyzer for Transient and steady-state in Rod Array - Liquid Metal Reactor for Flow Blockage analysis (MATRA-LMR-FB) code for the analysis of a subchannel blockage has been developed and evaluated through several experiments. The current version of the code is improved here by the implementation of a distributed resistance model which accurately considers the effect of flow resistance on wire spacers, by the addition of a turbulent mixing model, and by the application of a hybrid scheme for low flow regions. Validation calculations for the MATRA-LMR-FB code were performed for Oak Ridge National Laboratory (ORNL) 19-pin tests with wire spacers and Karlsruhe 169-pin tests with grid spacers. The analysis of the ORNL 19-pin tests conducted using the code reveals that the code has sufficient predictive accuracy, within a range of 5 $^{\circ}C$, for the experimental data with a blockage. As for the results of the analyses, the standard deviation for the Karlsruhe 169-pin tests, 0.316, was larger than the standard deviation for the ORNL 19-pin tests, 0.047.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.1
• /
• pp.95-102
• /
• 2021

Analysis of the fracture surface is one of the most important methods for determining the cause of equipment structural failure. Whether structural failure is caused by impact or fatigue is necessary information in industrial fields. For ferrous and non-ferrous metal materials, two fracture phenomena are generated on the fracture surface: ductile and brittle fractures. In this study, machine learning predicts whether the fracture is based on ductile or brittle when structurural failure is caused by impact. The K-means algorithm calculates this ratio by clustering the brittle and ductile fracture data from a photograph of the impact fracture surface, unlike the existing method, which calculates the fracture surface ratio by comparison with the grid type or the reference fracture surface shape.