• Applied Chemistry for Engineering
• /
• v.18 no.3
• /
• pp.255-261
• /
• 2007

The catalytic behavior of the manganese oxides was studied for the selective catalytic reduction with ammonia at a low temperature condition under $200^{\circ}C$. Outlet unreacted ammonia increases with decreasing temperature and increasing $NH_3/NOx$ mole ratio, however $NO_2$ shows an opposite result. $NO_2$ is generated by the adsorption of NO on the catalyst and the following oxidization to nitrates. Unreacted NH3 slip is not observed even at the $NH_3/NOx$ feed ratio above 1.0 due to the reaction between formed nitrates on the catalyst and adsorbed ammonia. The addition of Zr increases $NO_2$ generation, whereas the addition of CeO2 on the catalyst decreases $NO_2$ generation. Furthermore, the additon of the metal oxide induce DeNOx efficiency to reduce.

• Journal of Electrochemical Science and Technology
• /
• v.6 no.4
• /
• pp.121-130
• /
• 2015

The micro emulsion method has been successfully used for preparing perovskite LaCoO₃ with uniform, fine-shaped nanoparticles showing high activity as electro catalysts in oxygen reduction reactions (ORRs). They are, therefore, promising candidates for the air-cathode in metal-air rechargeable batteries. Since the activity of a catalyst is highly dependent on its specific surface area, nanoparticles of the perovskite catalyst are desirable for catalyzing both oxygen reduction and evolution reactions. Herein, LaCoO₃ powder was also prepared by sol-gel method for comparison, with a broad particle distribution and high agglomeration. The electro catalytic properties of LaCoO₃ and LaCoO₃-carbon Super P mixture layers toward the ORR were studied comparatively using the rotating disk electrode technique in 0.1 M KOH electrolyte to elucidate the effect of carbon Super P. Koutecky-Levich theory was applied to acquire the overall electron transfer number (n) during the ORR, calculated to be ~3.74 for the LaCoO₃-Super P mixture, quite close to the theoretical value (4.0), and ~2.7 for carbon-free LaCoO₃. A synergistic effect toward the ORR is observed when carbon is present in the LaCoO₃ layer. Carbon is assumed to be more than an additive, enhancing the electronic conductivity of the oxide catalyst. It is suggested that ORRs, catalyzed by the LaCoO₃-Super P mixture, are dominated by a 2+2-electron transfer pathway to form the final, hydroxyl ion product.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.70-79
• /
• 2022

Biodiesel production has attracted attention as a sustainable source of fuel and is a competitive alternate to diesel engines. The glycerol that is produced as a by-product is generally discarded as waste and can be converted to green chemicals such as acetins to increase bio-diesel profitability. Acetins find application in fuel, food, pharmaceutical and leather industries. Batch experiments and analysis have been previously conducted for synthesis of acetins using glycerol esterification reaction aided by sulfated metal oxide catalysts (SO₄^2-/CeO₂-ZrO₂). The aim of this study was to optimize process parameters: effects of mole ratio of reactants (glycerol and acetic acid), catalyst concentration and reaction temperature to maximize glycerol conversion/acetin selectivity. The optimum conditions for this reaction were determined using response surface methodology (RSM) designed as per a five-level-three-factor central composite design (CCD). Statistica software 10 was used to analyze the experimental data obtained. The optimized conditions obtained were molar ratio - 1:12, catalyst concentration - 6 wt.% and temperature -90 ℃. A packed bed reactor was fabricated and column studies were performed using the optimized conditions. The breakthrough curve was analyzed.

• Applied Chemistry for Engineering
• /
• v.9 no.1
• /
• pp.129-134
• /
• 1998

Conversion of propane to acrylonitrile via ammoxidation was studied using physically mixed catalysts composed of $Nb_2O_5(10{\sim}30wt%)$ and $V_{0.4}Mo_1Te_{0.1}$. Catalytic activities of ammoxidation were improved by adding strong acidic niobium oxide to $V_{0.4}Mo_1Te_{0.1}$, the selectivities to acrylonitrile+propylene being remained constant. The maximum activity was obtained at the mixing ratio 25wt% niobium oxide in $Nb_2O_5-V_{0.4}Mo_1Te_{0.1}$. Niobium oxide was found to be a selective catalyst for the oxidative dehydrogenation of propane.

• Applied Chemistry for Engineering
• /
• v.27 no.6
• /
• pp.555-564
• /
• 2016

In recent years, methanol has attracted much attention since it can be cleanly manufactured by the combined use of atmospheric $CO_2$ recycling and water splitting via renewable energy. For the concept of "methanol economy", an active methanol synthesis catalyst should be prepared in a sophisticated manner rather than by empirical optimization approach. Even though Cu/ZnO-based catalysts prepared by coprecipitation are well known and have been extensively investigated even for a century, fundamental understanding on the precipitation chemistry and catalyst nanostructure has recently been achieved due to complexity of the necessary preparation steps such as precipitation, ageing, filtering, washing, drying, calcination and reduction. Herein we review the recent reports regarding the effects of various synthesis variables in each step on the physicochemical properties of materials in precursor, calcined and reduced states. The relationship between these characteristics and the catalytic performance will also be discussed because many variables in each step strongly influence the final catalytic activity, called "chemical memory". All discussion focuses on how to prepare a highly active Cu/ZnO-based catalyst for methanol synthesis. Furthermore, the preparation strategy we deliver here would be utilized for designing other coprecipitation-derived supported metal or metal oxide catalysts.

• Clean Technology
• /
• v.20 no.1
• /
• pp.7-12
• /
• 2014

Hydrogenolysis of glycerol to propylene glycol was performed over binary and ternary metal oxide catalysts. The conversion of glycerol and selectivity to propylene glycol were increased on Cu/Zn and Cu/Cr mixed oxides compared to pure CuO and ZnO oxides. The addition of alumina into Cu/Zn mixed oxide very highly increased the conversion of glycerol and selectivity to propylene glycol. The conversion of glycerol was increased with increasing the reaction temperature but the selectivity to propylene glycol was shown to have maximum value at $200^{\circ}C$ and then decreased at $250^{\circ}C$. The conversion of glycerol and selectivity to propylene glycol were decreased with increasing the glycerol concentration.

• Korean Journal of Materials Research
• /
• v.21 no.5
• /
• pp.283-287
• /
• 2011

As the performance of microelectronic devices is improved, the use of copper as a heat dissipation member is increasing due to its good thermal conductivity. The high thermal conductivity of copper, however, leads to difficulties in the joining process. Satisfactory bonding with copper is known to be difficult, especially if high shear and peel strengths are desired. The primary reason is that a copper oxide layer develops rapidly and is weakly attached to the base metal under typical conditions. Thus, when a clean copper substrate is bonded, the initial strength of the joint is high, but upon environmental exposure, an oxide layer may develop, which will reduce the durability of the joint. In this study, an epoxy adhesive formulation was investigated to improve the strength and reliability of a copper to copper joint. Epoxy hardeners such as anhydride, dihydrazide, and dicyandiamide and catalysts such as triphenylphosphine and imidazole were added to an epoxy resin mixture of DGEBA and DGEBF. Differential scanning calorimetry (DSC) analyses revealed that the curing temperatures were dependent on the type of hardener rather than on the catalyst, and higher heat of curing resulted in a higher Tg. The reliability of the copper joint against a high temperature and high humidity environment was found to be the lowest in the case of dihydrazide addition. This is attributed to its high water permeability, which led to the formation of a weak boundary layer of copper oxide. It was also found that dicyandiamide provided the highest initial joint strength and reliability while anhydride yielded intermediate performance between dicyandiamide and dihydrazide.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.199-199
• /
• 2011

The addition of a carbanion to ${\yen}{\acute{a}}{\yen}{\hat{a}}$-unsaturated carbonyl compounds is of importance in the C-C bond formation reactions for modern pharmaceuticals and organic synthesis. Recently, heterogeneous asymmetric catalysis became more attractive area of research because of the easy recovery and separation of the catalyst from the reaction system. Most of synthetic methods for heterogeneous catalysts were grafting or immobilization of homogeneous catalyst onto the solid supports. Trans-1,2-Diaminocyclohexane(DACH) and L-proline ligands have been enormously used as chiral ligands in several catalytic transformation under homogenous conditions. Our group prepared l-proline functionalized mesoporous silica was synthesized under acidic condition using a poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock copolymer template (EO20PO70EO20, Pluronic P-123, BASF). Furthermore, we successfully directly synthesized trans-1,2 diaminocyclohexane functionalized mesoporous silica by using microwave method. The direct functionalization of chiral ligand into the framework of mesoporous materials is expected to be useful for the heterogeneous asymmetric catalysis. So, we adopt the direct synthesis of chiral ligand functionalized mesoporous silica by using thermal and microwave irradiation. Then, chiral ligand functionalized mesoporous silicas were applied to enantioselective asymmetric catalytic reactions.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.217-222
• /
• 2012

The synthesis of dimethyl carbonate(DMC) is a promising reaction for the use of naturally abundant carbon dioxide. DMC has gained considerable interest owing to its versatile chemical reactivity and unique properties such as high oxygen content, low toxicity, and excellent biodegradability. In this study, the synthesis of DMC through the transesterification of ethylene carbonate(EC) with methanol was investigated by using ionic liquid and metal oxide catalysts. The screening test of different catalysts revealed that choline hydroxide ([Choline][OH]) and 1-n-butyl-3-methyl imidazolium hydroxide([BMIm][OH]) had better catalytic performance than metal salts catalysts such as MgO, ZnO and CaO. The effects of reaction parameters such as reaction temperature, MeOH/EC mole ratio, and carbon dioxide pressure on the reactivity of [Choline][OH] catalyst were discussed. High temperature and high MeOH/EC mole ratio were favorable for high conversion of EC. However, the yield of DMC showed a maximum when carbon dioxide pressure was 1.34 MPa, and then it decreased for higher carbon dioxide pressure. Zinc chloride($ZnCl_2$) was used as co-catalyst with the ionic liquid catalyst. The mixed catalyst showed a synergy effect on the EC conversion and DMC yield probably due to the acid-base properties of the catalysts.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.720-725
• /
• 2011

Gold catalysts supported on metal-oxides were prepared by co-precipitation using the various metal nitrates and chloroauric acid as precursors, and effect of water addition on the catalytic activity in CO oxidation was investigated. Among the various supported gold catalysts, Au/$Co_{3}O_{4}$ and Au/ZnO catalysts showed the excellent activity for CO oxidation. Water in the reactant gas had a negative effect on the oxidation activity over Au/$Co_{3}O_{4}$ catalysts and a positive effect on that over Au/ZnO, which means the activity depends strongly on the nature of support. It was also confirmed that no significant change in the particle size of gold was observed after reaction both in dry and wet conditions. This fact suggested that the deactivated catalyst due to a carbonate species could be regenerated by water addition in the reactant gas.