• 한국전기전자재료학회논문지
• /
• 제23권7호
• /
• pp.575-579
• /
• 2010

The technologies of Ni/Cu plating contact is attributed to the reduced series resistance caused by a better contact conductivity of Ni with Si and the subsequent electroplating of Cu on Ni. The ability to pattern narrower grid lines for reduced light shading was combined with the lower resistance of a metal silicide contact and an improved conductivity of the plated deposit. This improves the FF (fill factor) as the series resistance is reduced. This is very much requried in the case of low concentrator solar cells in which the series resistance is one of the important and dominant parameter that affect the cell performance. A Selective emitter structure with highly dopeds regions underneath the metal contacts, is widely known to be one of the most promising high-efficiency solution in solar cell processing In this paper the formation of a selective emitter, and the nickel silicide seed layer at the front side metallization of silicon cells is considered. After generating the nickel seed layer the contacts were thickened by Cu LIP (light induced plating) and by the formation of a plated Ni/Cu two step metallization on front contacts. In fabricating a Ni/Cu plating metallization cell with a selective emitter structure it has been shown that the cell efficiency can be increased by at least 0.2%.

• 한국가구학회지
• /
• 제28권3호
• /
• pp.207-223
• /
• 2017

Jeonju-Jang is the wood furniture that was made in Chonbuk Jeonju province during the Joseon Dynasty, and was used by middle-upper social classes. It has value as a local cultural heritage because it has unique characteristics in terms of the shape of the furniture, the metal ornament and various functions are integrated in accordance with user's requirements. Therefore, the purpose of this study is to define the structural characteristics of the Jeonju-Jang through case studies of 16 existing artifacts in order to preserve and inherit the value as local cultural resources. The conclusion is as follows. First, Jeonju-Jang in the late period of Joseon Dynasty that is made up of one board to the bottom with the binding of the board. and the front wall, the Juibyuckkan and the Meoruemkan are omitted or made small, so the structure of the surface is simple. There are three or four drawers under the Cheon pan(top plate). There are drawers and shelf inside the hinged door. In the case of a two-layer type, there is a Gaegumeong type door which has half of one side hinged. Second, Jeonju-Jang of the Japanese Ruling Era had a Juibyuckkan by frame binding and an increase in the number of Meoruemkan. and it had independent legs. The Cheon-pan(top plate) was more left and right than both sides. Third, in the late Joseon Dynasty period as a feature of the metal ornaments, cast iron and yellow brass were used as materials. In the Japanese Ruling Era, nickel was mainly used. Various patterns were engraved and the number increased, and it became gorgeous surface as a whole.

• 센서학회지
• /
• 제22권2호
• /
• pp.130-135
• /
• 2013

This study proposed a noble process to fabricate TSV (Through Silicon Via) structure which has lower cost, shorter production time, and more simple fabrication process than plating method. In order to produce the via holes, the Si wafer was etched by a DRIE (Deep Reactive Ion Etching) process. The via hole was $100{\mu}m$ in diameter and $400{\mu}m$ in depth. A dielectric layer of $SiO_2$ was formed by thermal oxidation on the front side wafer and via hole side wall. An adhesion layer of Ti and a seed layer of Au were deposited. Soldering process was applied to fill the via holes with solder paste and metal powder. When the solder paste was used as via hole metal line, sintering state and electrical properties were excellent. However, electrical connection was poor due to occurrence of many voids. In the case of metal powder, voids were reduced but sintering state and electrical properties were bad. We tried the via hole filling process by using mixing solder paste and metal powder. As a consequence, it was confirmed that mixing rate of solder paste (4) : metal powder (3) was excellent electrical characteristics.

• 한국화재소방학회논문지
• /
• 제31권1호
• /
• pp.89-97
• /
• 2017

본 연구에서는 서비스센터에서 정비를 받고 출고한 날로부터 5일 후 터널 주행 중에 발생한 디젤승용차 화재 사례를 조사분석하였다. 조사분석한 결과, 배기구 내부에 흰색 이물질이 다량 부착되어 있었고, 배기관의 중간에 설치된 diesel particulate filter (DPF) 위쪽의 차열재가 용융 및 소실되어 있었고, DPF 위쪽의 차실 내부 금속재 바닥이 천공되어 금속재 바닥 위에 놓인 고무매트가 연소된 케이스이었다. 그리고 DPF 앞쪽의 배기관에는 과열흔적이 없고 DPF부터 배기구까지의 배기관에 과열흔적이 있는 특이점이 있었다. 이러한 특이점들은 DPF가 과열되고 DPF에서 발화된 경우에만 나타나므로 이 승용차화재는 DPF 내부 과열에 의해 발생한 것으로 분석할 수 있었다. 그리고 이 승용차화재조사를 통해 디젤승용차 화재원인조사 과정에서 배기구 내부에서 흰색 이물질이 확인되는 경우에는 DPF를 분리하여 DPF 내부의 손상을 조사하여 화재원인을 판정하여야 함을 알 수 있었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.91.2-91.2
• /
• 2010

The use of plated front contact for metallization of silicon solar cell may alternative technologies as a screen printed and silver paste contact. This technologies should allow the formation of contact with low contact resistivity a high line conductivity and also reduction of shading losses. The better performance of Ni/Cu contacts is attributed to the reduced series resistance due to better contact conductivity of Ni with Si and subsequent electroplating of Cu on Ni. The ability to pattern narrower grid lines for reduced light shading combined with the lower resistance of a metal silicide contact and improved conductivity of plated deposit. This improves the FF as the series resistance is deduced. This is very much required in the case of low concentrator solar cells in which the series resistance is one of the important and dominant parameter that affect the cell performance. A selective emitter structure with highly dopes regions underneath the metal contacts, is widely known to be one of the most promising high-efficiency solution in solar cell processing. This paper using selective emitter structure technique, fabricated Ni/Cu plating metallization cell with a cell efficiency of 17.19%.

• 한국재료학회지
• /
• 제27권2호
• /
• pp.107-112
• /
• 2017

The BCBJ (Back Contact and Back Junction) or back-lit solar cell design eliminates shading loss by placing the pn junction and metal electrode contacts all on one side that faces away from the sun. However, as the electron-hole generation sites now are located very far from the pn junction, loss by minority-carrier recombination can be a significant issue. Utilizing Medici, a 2-dimensional semiconductor device simulation tool, the interdependency between the substrate thickness and the minority-carrier recombination lifetime was studied in terms of how these factors affect the solar cell power output. Qualitatively speaking, the results indicate that a very high quality substrate with a long recombination lifetime is needed to maintain the maximum power generation. The quantitative value of the recombination lifetime of minority-carriers, i.e., electrons in p-type substrates, required in the BCBJ cell is about one order of magnitude longer than that in the front-lit cell, i.e., $5{\times}10^{-4}sec$ vs. $5{\times}10^{-5}sec$. Regardless of substrate thickness up to $150{\mu}m$, the power output in the BCBJ cell stays at nearly the maximum value of about $1.8{\times}10^{-2}W{\cdot}cm^{-2}$, or $18mW{\cdot}cm^{-2}$, as long as the recombination lifetime is $5{\times}10^{-4}s$ or longer. The output power, however, declines steeply to as low as $10mW{\cdot}cm^{-2}$ when the recombination lifetime becomes significantly shorter than $5{\times}10^{-4}sec$. Substrate thinning is found to be not as effective as in the front-lit case in stemming the decline in the output power. In view of these results, for BCBJ applications, the substrate needs to be only mono-crystalline Si of very high quality. This bars the use of poly-crystalline Si, which is gaining wider acceptance in standard front-lit solar cells.

• Design & Manufacturing
• /
• 제12권2호
• /
• pp.40-45
• /
• 2018

Recently, in construction equipment machinery production, development has focused on environmentally-friendly functions to improve existing production capacity. For excavators as well, emphasis has been placed on response to environmental regulations, miniaturization, and noise reduction, while technology is being developed considering cost reduction and safety.Accordingly, the front support, an inner reinforcement part of the excavator, as well as high-strength steel plates to improve safety and reduce weight, are being applied.However, in the case of high-strength materials, Springback occurs in the final formed part due to high residual stress during product forming. Derivation of a forming or product shaping process to reduce springback is needed. Accordingly, regarding the front support, an inner reinforcement part of the excavator, this study derived a method to improve springback and secure shape stiffness through analysis of the springback occurrence rate and springback causes through a forming analysis.As for the results of analyzing the springback occurrence rate of existing products through forming analysis, springback of -22.6 mm < z < 27.35 mm occurred on the z-axis, and it was confirmed that springback occurred due to the stiffness reinforcing bead of the upper and middle parts of the product.To control product residual stress and springback, we confirmed a tendency of springback reduction through local pre-cutting and stiffness reinforcement bead relocation.In the local pre-cutting model, springback was slightly reduced by 5.3% compared with the existing model, an insignificant reduction effect. In the stiffness reinforcement bead relocation model, when an X-shaped stiffness reinforcement bead was added to each corner portion of the product, springback was reduced by at least 80%.The X-shaped bead addition model was selected as the springback reduction model, and the level of stiffness compared to the existing model was confirmed through a structural analysis.The X-shaped bead additional model showed a stress springback of 90% and springback reduction of 7.4% compared with the existing model, indicating that springback and stiffness will be reinforced.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제30회 춘계학술대회논문집
• /
• pp.203-206
• /
• 2008

본 연구는 고체 추진기관에 적용되는 내열재를 autoclave 방식이 아닌 hot press molding으로 제작하여 연소관에 접착 가능한 상태의 내열재로 제작하는데 초점을 두고 있다. EPDM/kevlar를 기본 조성으로 내열재 원료가 구성되고, 미가류 sheet 상태로 공급된다. 전방 내열재는 금형을 사용하여 preform 상태로 1차 제작하고, boots를 구형하기 위해 두개의 preform 사이에 modified nylon film을 사용하여 제작 하였다. 실린더 부위를 포함하고 있는 후방 내열재는 특별히 설계된 하나의 금형으로 제작되었고, boots 부위는 초경합금 칼날을 가지고 있는 장비에 의해 실현되었다.

• 대한환경공학회지
• /
• 제31권1호
• /
• pp.29-34
• /
• 2009

표면처리폐수 내 질산성 질소를 제거하기 위한 전기화학적 처리공정에서 전극간격, 환원제, 1단 처리수 반송, 타 물질과 동시 처리 등 네 가지 조건을 변화시키며 실험을 진행하였다. 실험 결과, 전극간격은 10 mm일 때 질산성 질소 제거효율이 높았으며 10 mm 보다 전극간격이 좁아질 경우 농도분극 현상의 증가로 인해 제거효율이 감소하며 10 mm 보다 넓어질 경우 전압이 상승하여 에너지 소모가 증가하였다. 환원제 영향에 대한 실험 결과, 질산성 질소가 환원되는 과정에서 수소가 소모되기 때문에 수소이온 농도가 높은 산성조건에서 더 원활한 환원반응이 이루어졌으며 아연을 1.2배 투입할 경우 질산성 질소와의 반응량이 증가하여 질산성 질소 제거효율이 증가하였다. 1단 처리수를 반송할 경우 난류가 형성되어 환원전극에 부착된 아연이 탈착되어 재 이용되고 내부 확산이 증가하여 농도분극현상이 감소함으로 인해 질산성 질소 제거효율이 증가하였으며 아연 투입량 감소 효과가 나타났다. 암모니아성 질소는 질산성 질소 제거에 영향을 미치지 않았고 폐수 내 염소성분이 충분할 경우 질산성 질소와 동시 처리에도 문제가 없는 것으로 나타났다. 중금속은 환원되는 과정에서 전자를 소모하여 질산성 질소 제거효율은 감소하지만 전류밀도 증가나 본 장치의 전단을 중금속 제거용으로 사용하는 방법 등으로 해결이 가능할 것으로 생각한다.

• 한국대기환경학회지
• /
• 제23권1호
• /
• pp.110-124
• /
• 2007

In this study, the control efficiency of odorous compounds was measured from diverse control process units of 14 individual companies located within the Ban-Wall industrial complex of Ansan city, Korea (January to July 2005), To quantify the control efficiency levels of major odorous compounds, we collected odor samples from both the front and rear side of 17 control process units ($N=17{\times}2=34$). If the control efficiency is compared for each of 32 compounds between different process units, wet scrubber (WS) was found to be the most effective unit in terms of the sum of pollutants showing the positive control signals. Although the WS system shows generally a good control pattern for VOC, it is not the case for most index odorous pollutants; only 3 out of 12 index compounds were found to show positive control efficiencies. The results of the study also indicated that the control efficiency differ greatly between different industrial sectors and/or control process types. In the case of leather industry, carbonyl compounds were found to exhibit the highest control efficiency with its values varying from 19 to 90%. On the other hand, in the case of metal production sector, VOC recorded the maximum control efficiency with values varying from 18 to 79%. According to this study, most air pollution control facilities operated in most companies show fairly poor control efficiencies for most malodor compounds. Hence, to obtain best control efficiency of odorous pollutant emission, acquisition of better information on source characteristics and establishment of effective control technologies are highly demanding.