• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.376-377
• /
• 2006

Chemical Mechanical Planarization (CMP) has emerged as an enabling technology for the manufacturing of multi-level metal interconnects used in high-density Integrated Circuits (IC). Recently, multi-level structures have been also widely used m the MEMS device such as micro engines, pressure sensors, micromechanical fluid pumps, micro mirrors and micro lenses. Especially, among the thin films available in IC technologies, polysilicon has probably found the widest range of uses in silicon technology based MEMS. This paper presents the characteristic of polysilicon CMP for multi-level MEMS structures. Two-step CMP process verifies that is possible to decrease dishing amount with two type of slurries characteristics. This approach is attractive because two-step CMP process can be decreased dishing amount considerably more then just one CMP process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04b
• /
• pp.93-96
• /
• 2004

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric(IMD) layer with free-defect. The effect of alternative commerical slurries pads, and post-CMP cleaning alternatives are discuess, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. we investigated the performance of $SnO_2$-CMP process using commonly used silica slurry, ceria slurry, tungsten slurry. This study shows removal rate and nonuniformity of $SnO_2$ thin film used to gas sensor by using Ceria, Silica, W-Slurry after CMP process. This study also shows the relation between partical size and CMP with partical size analysis of used slurry.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.189-192
• /
• 2001

Recently, STI process is getting attention as a necessary technology for making high density of semiconductor by devices isolation method. However, it does have various problems caused by CMP nprocess, such as torn oxide defects, nitride residues on oxide, damages of si active region, contaminations due to post-CMP cleaning, difficulty of accurate end point detection in CMP process, etc. In this work, the various defects induced by CMP process was introduced and the above mentioned problems of CMP process was examined in detail. Finally, the guideline of future CMP process was presented to reduce the effects of these defects.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.189-192
• /
• 2001

Recently, STI process is getting attention as a necessary technology for making high density of semiconductor by devices isolation method. However, it does have various problems caused by CMP process, such as torn oxide defects, nitride residues on oxide, damages of si active region, contaminations due to post-CMP cleaning, difficulty of accurate end point detection in CMP process, etc. In this work, the various defects induced by CMP process was introduced and the above mentioned Problems of CMP process was examined in detail. Finally, the guideline of future CMP process was presented to reduce the effects of these defects.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.184-187
• /
• 2003

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric(IMD) lyaer with free-defect. The effect of alternative commerical slurries pads, and post-CMP cleaning alternatives are discuess, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. we investigated the performance of $SnO_2-CMP$ process using commonly used silica slurry, ceria slurry, tungsten slurry. This study shows removal rate and nonuniformity of $SnO_2$ thin film used to gas sensor by using Ceria, Silica, W-Slurry after CMP process. This study also shows the relation between partical size and CMP with partical size analysis or used slurry.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.2
• /
• pp.62-66
• /
• 2006

Advanced CMP conditioner design requires investigations of key conditioner manufacturing parameters and their effects on pad surface and then wafer performance. In the present investigation, diamond shape, concentration, distribution, and other key manufacturing parameters are considered to improve CMP process stability and conditioner life. Self avoiding random distribution ($SARD^{TM}$) of diamond abrasives has been developed and both numerical simulation and experimental results show very stable and reliable polishing performance.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.81-82
• /
• 2006

Chemical mechanical polishing (CMP) technology has been widely used for global planarization of multi-level interconnection for ULSI applications. However, the cost of ownership and cost of consumables are relatively high because of expensive slurry. In this paper, so as to investigate the influence of mixed abrasive slurry (MAS), such as $ZrO_2$, $CeO_2$, and $MnO_2$ for Ti-CMP application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05b
• /
• pp.34-37
• /
• 2001

As the integrated circuit device shrinks to smaller dimensions, chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric (IMD) layer with free-defect. However, as the inter-metal dielectrics (IMD) layer gets thinner, micro-scratches are becoming as major defects. Micro-scratches are generated by agglomerated slurry, solidified and attached slurry in pipe line of slurry supply system. To prevent agglomerated slurry particle from inflow, we installed 0.5${\mu}m$ POU (point of use) filter, which is depth-type filter and has 80% filtering efficiency for the $1.0{\mu}m$ size particle. In this paper, we studied the relationship between defect generation and pad count to understand the exact efficiency of the slurry filtration, and to find out the appropriate pad usage. Our preliminary results showed that it is impossible to prevent defect-causing particles perfectly through the depth-type filter. Thus, we suggest that it is necessary to optimize the flow rate of slurry to overcome depth type filters weak-point, and to install the high spray of de-ionized Water (DIW) with high pressure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.81-81
• /
• 2007

Chemical mechanical polishing (CMP) 공정은 deep 서브마이크론 집적회로의 다층배선구조률 실현하기 위해 inter-metal dielectric (IMD), inter-layer dielectric layers (ILD), pre-metal dielectric (PMD) 층과 같은 절연막 외에도 W, Al, Cu와 같은 금속층을 평탄화 하는데 효과적으로 사용되고 있으며, 다양한 소자 제작 및 새로운 물질 등에도 광범위하게 응용되고 있다. 하지만 Cu damascene 구조 제작으로 인한 CMP 응용 과정에서, 기계적으로 깨지기 쉬운 65 nm의 소자 이하의 구조에서 새로운 저유전상수인 low-k 물질의 도입으로 인해 낮은 하력의 기계적 연마가 필요하게 되었다. 본 논문에서는 전기화학적 기계적 연마 적용을 위해, I-V 특성 곡선을 이용하여 active, passive, transient, trans-passive 영역의 전기화학적 특성을 알아보았으며, Cu 막의 표면 형상을 알아보기 위해 scanning electron microscopy (SEM) 측정과 energy dispersive spectroscopy (EDS) 분석을 통해 금속 화학적 조성을 조사하였다.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1600-1604
• /
• 2004

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric(IMD) layer with free-defect. The effect of alternative commerical slurries pads, and post-CMP cleaning alternatives are discuess, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. we investigated the performance of $SnO_2$-CMP process using commonly used silica slurry, ceria slurry, tungsten slurry. This study shows removal rate and nonuniformity of $SnO_2$ thin film used to gas sensor by using Ceria, Silica, W-Slurry after CMP process. This study also shows the relation between partical size and CMP with partical size analysis of used slurry.