• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.8
• /
• pp.56-63
• /
• 2010

This work proposes a 12b 100MS/s 0.13um CMOS pipeline ADC for battery-powered mobile video applications such as DVB-Handheld (DVB-H), DVB-Terrestrial (DVB-T), Satellite DMB (SDMB), and Terrestrial DMB (TDMB) requiring high resolution, low power, and small size at high speed. The proposed ADC employs a three-step pipeline architecture to optimize power consumption and chip area at the target resolution and sampling rate. A single shared and switched op-amp for two MDACs removes a memory effect and a switching time delay, resulting in a fast signal settling. A two-step reference selection scheme for the last-stage 6b FLASH ADC reduces power consumption and chip area by 50%. The prototype ADC in a 0.13um 1P7M CMOS technology demonstrates a measured DNL and INL within 0.40LSB and 1.79LSB, respectively. The ADC shows a maximum SNDR of 60.0dB and a maximum SFDR of 72.4dB at 100MS/s, respectively. The ADC with an active die area of 0.92 $mm^2$ consumes 24mW at 1.0V and 100MS/s. The FOM, power/($f_s{\times}2^{ENOB}$), of 0.29pJ/conv. is the lowest of ever reported 12b 100MS/s ADCs.

• Journal of the Korea Society of Computer and Information
• /
• v.17 no.6
• /
• pp.1-11
• /
• 2012

As the process technology scales down, multi-core processors cause serious problems such as increased interconnection delay, high power consumption and thermal problems. To solve the problems in 2D multi-core processors, researchers have focused on the 3D multi-core processor architecture. Compared to the 2D multi-core processor, the 3D multi-core processor decreases interconnection delay by reducing wire length significantly, since each core on different layers is connected using vertical through-silicon via(TSV). However, the power density in the 3D multi-core processor is increased dramatically compared to that in the 2D multi-core processor, because multiple cores are stacked vertically. Unfortunately, increased power density causes thermal problems, resulting in high cooling cost, negative impact on the reliability. Therefore, temperature should be considered together with performance in designing 3D multi-core processors. In this work, we analyze the temperature of the cache in quad-core processors varying cache organization. Then, we propose the low-temperature cache organization to overcome the thermal problems. Our evaluation shows that peak temperature of the instruction cache is lower than threshold. The peak temperature of the data cache is higher than threshold when the cache is composed of many ways. According to the results, our proposed cache organization not only efficiently reduces the peak temperature but also reduces the performance degradation for 3D quad-core processors.

• Journal of KIISE:Computer Systems and Theory
• /
• v.31 no.11
• /
• pp.626-634
• /
• 2004

In a client-server model, network server systems suffer from both heavy communication and computational loads. While communication channels become increasingly speedy, the existing protocol stack architectures still include mainly three performance bottlenecks of protocol stack processing, system call, and network interrupt overheads. To address these obstacles, in this paper we present a host-independent network system where a network interface card (NIC) is utilized in an efficient manner. First, by offloading network-related portion to the NIC, the host can fully utilize its processing power for other useful purposes. Second, it eliminates the system call overhead, such as context-switching and memory copy operations, since the host communicates with the NIC through its user-level libraries. Third, it a] so reduces the network interrupt operation count as the host handles the interrupt in a segment instead of a packet. The experimental results show that the proposed network system reduces the host CPU overhead for communication system by 68-71%. It also shows that the proposed system improves the communication speed by 11-83% under heavy computational and communication load conditions.

• The Journal of Korean Institute of Next Generation Computing
• /
• v.15 no.2
• /
• pp.39-49
• /
• 2019

Recently, CPU-GPU integrated heterogeneous multicore processors have been widely used for improving the performance of computing systems. Heterogeneous multicore processors integrate CPUs and GPUs on a single chip where CPUs and GPUs share the LLC(Last Level Cache). This causes a serious cache contention problem inside the processor, resulting in significant performance degradation. In this paper, we propose the partitioned LLC architecture to solve the cache contention problem in heterogeneous multicore processors. We analyze the performance impact varying the LLC size of CPUs and GPUs, respectively. According to our simulation results, the bigger the LLC size of the CPU, the CPU performance improves by up to 21%. However, the GPU shows negligible performance difference when the assigned LLC size increases. In other words, the GPU is less likely to lose the performance when the LLC size decreases. Because the performance degradation due to the LLC size reduction in GPU is much smaller than the performance improvement due to the increase of the LLC size of the CPU, the overall performance of heterogeneous multicore processors is expected to be improved by applying partitioned LLC to CPUs and GPUs. In addition, if we develop a memory management technique that can maximize the performance of each core in the future, we can greatly improve the performance of heterogeneous multicore processors.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.7
• /
• pp.1071-1077
• /
• 2022

A security SoC that can be used to implement elliptic curve cryptography (ECC) based public-key infrastructures was designed. The security SoC has an architecture in which a hardware accelerator for the elliptic curve digital signature algorithm (ECDSA) is interfaced with the Cortex-A53 CPU using the AXI4-Lite bus. The ECDSA hardware accelerator, which consists of a high-performance ECC processor, a SHA3 hash core, a true random number generator (TRNG), a modular multiplier, BRAM, and control FSM, was designed to perform the high-performance computation of ECDSA signature generation and signature verification with minimal CPU control. The security SoC was implemented in the Zynq UltraScale+ MPSoC device to perform hardware-software co-verification, and it was evaluated that the ECDSA signature generation or signature verification can be achieved about 1,000 times per second at a clock frequency of 150 MHz. The ECDSA hardware accelerator was implemented using hardware resources of 74,630 LUTs, 23,356 flip-flops, 32kb BRAM, and 36 DSP blocks.

• International Journal of Advanced Culture Technology
• /
• v.10 no.1
• /
• pp.248-252
• /
• 2022

The environment refers to what is surrounded by something during human life. This environment is related to the way humans live, and presents various problems on how to perceive the surrounding environment and how the behaviors that constitute the environment support the elements necessary for human life. Humans have an interest in the supportability of the environment as the interrelationship increases as humans perceive and understand the environment and accept the factors supported by the environment. In space, human movement starts from one space to the next and exchanges stimuli and reactions with the environment until reaching a target point. These human movements start with subjective judgment and during gait movement, the spatial environment surrounding humans becomes a collection of information necessary for humans and gives stimulation. will do. In this process, in particular, humans move along the movement path through movement in space and go through displacement perception and psychological changes, and recognize a series of spatial continuity. An image of thinking is formed[1]. In this process, spatial experience is perceived through the process of filtering by the senses in the real space, and the result of cognition is added through the process of subjective change accompanied by memory and knowledge, resulting in human movement. As such, the spatial search behavior begins with a series of perceptual and cognitive behaviors that arise in the process of human beings trying to read meaning from objects in the environment. Here, cognition includes the psychological process of sorting out and judging what the information is in the process of reading the meaning of the external environment, conditions, and material composition, and perception is the process of accepting information as the first step. It can be said to be the cognitive ability to read the meaning of the environment given to humans. Therefore, if we can grasp the perception of space while moving and human behavior as a response to perception, it will be possible to predict how to grasp it from a human point of view in a space that does not exist. Modern people have the theme of reminiscing dog-friendly hotels for the healing of petloss syndrome, and this thesis attempts to approach the life of companions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.880-886
• /
• 2007

We have proposed a new "hybrid" envelope elimination and restoration(EER) transmitter architecture using an efficiency optimized power amplifier(PA) and modified bias modulator. The efficiency of the PA at the average drain voltage is very important for the overall transmitter efficiency because the PA operates mostly at the average power region of the modulation signal. Accordingly, the efficiency of the PA has been optimized at the region. Besides, the bias modulator has been accompanied with the emitter follower for the minimization of memory effect. A saturation amplifier, class $F^{-1}$ is built using a 5-W PEP LDMOSFET for forward-link single-carrier wideband code-division multiple-access(WCDMA) at 1-GHz. For the interlock experiment, the bias modulator has been built with the efficiency of 64.16% and peak output voltage of 31.8 V. The transmitter with the proposed PA and bias modulator has been achieved an efficiency of 44.19%, an improvement of 8.11%. Besides, the output power is enhanced to 32.33 dBm due to the class F operation and the PAE is 38.28% with ACLRs of -35.9 dBc at 5-MHz offset. These results show that the proposed architecture is a very good candidate for the linear and efficient high power transmitter.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.38 no.4
• /
• pp.25-38
• /
• 2020

For the purpose of recording Folk House Garden, this study was to review the historical value, location, space composition, Placememnt of the Building, garden composition, and management status of Folk House Garden designated as a cultural asset in Jeolla-do and to promote continuous maintenance and preservation in the future and enhance its value. The results of the study are as follows. First, most of them have been influenced by the trend of the times, such as the creation of a modern private garden and the spread of agricultural and commercial development through the garden components influenced by the royal, Japanese, and Western styles. Second, there are differences in the spatial composition of private households and the way they handle sponsorship, depending on the geographical location. When the geographical features were divided into flat and sloping areas, private houses located on flat land were divided into walls, walls were placed around the support area, and flower systems and stone blocks were created. The private houses located on the slope were divided into two to three tiers of space, and the wooden plant, flower bed, and stone bed were naturally connected to the background forest without creating a wall at the rear hill. Third, the size of the house and the elements of the garden have been partially destroyed, damaged, and changed, and if there is a lack of records of the change process, there is a limit to the drawing floor plan. There were many buildings and garden components that were lost or damaged due to changes in the trend and demand of the times, and some of them without records had to rely on the memory of owners and managers. Fourth, the species in Warm Temperate Zone, which reflects the climatic characteristics of Jeolla-do, was produced, and many of the exotic species, not traditional ones, were introduced. Fifth, fine-grained tree management standards are needed to prepare for changes in spatial function and plant species considering modern convenience.

• Journal of Intelligence and Information Systems
• /
• v.26 no.2
• /
• pp.1-25
• /
• 2020

In this paper, we suggest an application system architecture which provides accurate, fast and efficient automatic gasometer reading function. The system captures gasometer image using mobile device camera, transmits the image to a cloud server on top of private LTE network, and analyzes the image to extract character information of device ID and gas usage amount by selective optical character recognition based on deep learning technology. In general, there are many types of character in an image and optical character recognition technology extracts all character information in an image. But some applications need to ignore non-of-interest types of character and only have to focus on some specific types of characters. For an example of the application, automatic gasometer reading system only need to extract device ID and gas usage amount character information from gasometer images to send bill to users. Non-of-interest character strings, such as device type, manufacturer, manufacturing date, specification and etc., are not valuable information to the application. Thus, the application have to analyze point of interest region and specific types of characters to extract valuable information only. We adopted CNN (Convolutional Neural Network) based object detection and CRNN (Convolutional Recurrent Neural Network) technology for selective optical character recognition which only analyze point of interest region for selective character information extraction. We build up 3 neural networks for the application system. The first is a convolutional neural network which detects point of interest region of gas usage amount and device ID information character strings, the second is another convolutional neural network which transforms spatial information of point of interest region to spatial sequential feature vectors, and the third is bi-directional long short term memory network which converts spatial sequential information to character strings using time-series analysis mapping from feature vectors to character strings. In this research, point of interest character strings are device ID and gas usage amount. Device ID consists of 12 arabic character strings and gas usage amount consists of 4 ~ 5 arabic character strings. All system components are implemented in Amazon Web Service Cloud with Intel Zeon E5-2686 v4 CPU and NVidia TESLA V100 GPU. The system architecture adopts master-lave processing structure for efficient and fast parallel processing coping with about 700,000 requests per day. Mobile device captures gasometer image and transmits to master process in AWS cloud. Master process runs on Intel Zeon CPU and pushes reading request from mobile device to an input queue with FIFO (First In First Out) structure. Slave process consists of 3 types of deep neural networks which conduct character recognition process and runs on NVidia GPU module. Slave process is always polling the input queue to get recognition request. If there are some requests from master process in the input queue, slave process converts the image in the input queue to device ID character string, gas usage amount character string and position information of the strings, returns the information to output queue, and switch to idle mode to poll the input queue. Master process gets final information form the output queue and delivers the information to the mobile device. We used total 27,120 gasometer images for training, validation and testing of 3 types of deep neural network. 22,985 images were used for training and validation, 4,135 images were used for testing. We randomly splitted 22,985 images with 8:2 ratio for training and validation respectively for each training epoch. 4,135 test image were categorized into 5 types (Normal, noise, reflex, scale and slant). Normal data is clean image data, noise means image with noise signal, relfex means image with light reflection in gasometer region, scale means images with small object size due to long-distance capturing and slant means images which is not horizontally flat. Final character string recognition accuracies for device ID and gas usage amount of normal data are 0.960 and 0.864 respectively.

• Journal of KIISE:Computing Practices and Letters
• /
• v.15 no.3
• /
• pp.154-166
• /
• 2009

Database query and reporting tools, OLAP tools and data mining tools are typical front-end tools in Business Intelligence environment which is able to support gathering, consolidating and analyzing data produced from business operation activities and provide access to the result to enterprise's users. Traditional reporting tools have an advantage of creating sophisticated dynamic reports including SQL query result sets, which look like documents produced by word processors, and publishing the reports to the Web environment, but data source for the tools is limited to RDBMS. On the other hand, OLAP tools and data mining tools have an advantage of providing powerful information analysis functions on each own way, but built-in visualization components for analysis results are limited to tables or some charts. Thus, this paper presents a system that integrates three typical front-end tools to complement one another for BI environment. Traditional reporting tools only have a query editor for generating SQL statements to bring data from RDBMS. However, the reporting tool presented by this paper can extract data also from OLAP and data mining servers, because editors for OLAP and data mining query requests are added into this tool. Traditional systems produce all documents in the server side. This structure enables reporting tools to avoid repetitive process to generate documents, when many clients intend to access the same dynamic document. But, because this system targets that a few users generate documents for data analysis, this tool generates documents at the client side. Therefore, the tool has a processing mechanism to deal with a number of data despite the limited memory capacity of the report viewer in the client side. Also, this reporting tool has data structure for integrating data from three kinds of data sources into one document. Finally, most of traditional front-end tools for BI are dependent on data source architecture from specific vendor. To overcome the problem, this system uses XMLA that is a protocol based on web service to access to data sources for OLAP and data mining services from various vendors.