• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.572-575
• /
• 2008

Flow-field design has much influence over the performance of proton exchange membrane fuel cell (PEMFC) because it affects the pressure magnitude and distribution of the reactant gases. To obtain the pressure magnitude and distribution of reactant gases in four kinds of flow-field designs without additional measurement equipment, computational fluid dynamics (CFD) analysis was performed. After the CFD analysis, the performance values of PEMFC according to the flow-field configurations were measured via a single cell test. As expected, the pressure differences due to different flow-field configurations were related to the PEMFC performance because the actual performance results showed the same tendency as the results of the CFD analysis. A large pressure drop resulted in high PEMFC performance. So, the single serpentine configuration gave the highest performance. On the other hand, the parallel flow-field configuration gave the lowest performance because the pressure difference between inlet and outlet was the lowest.

• 전기학회논문지
• /
• 제59권1호
• /
• pp.138-143
• /
• 2010

This paper presents the analysis, the fabrication and the test results of a micro passive gas pressure regulator to keep the outlet pressure costant even for a widely-varying inlet pressure. This device is to regulate the outlet pressure according to the applied reference pressure based on the pressure balancing mechanism of the structure including a membrane and a valve. This regulator consists of four layers; a bulk-micromachined silicon substrate, a sandblasted glass substrate, a PDMS valve seat layer and a glass valve layer. The device size is $10\times13\times1.7 mm3$. The device was fabricated by micromachining. The characteristic of the device was analyzed and tested. The characteristic of the fabricated pressure regulator is similar to that obtained from the analysis. The pressure regulator of this paper is feasible for portable systems and miniature drug delivery systems.

• 한국생산제조학회지
• /
• 제22권2호
• /
• pp.235-240
• /
• 2013

This paper presents a disposable microfluidic infusion pump using the restoring force of elastomeric membrane of Polydimethylsiloxane. Microfluidic infusion pump consists of hydraulic resistance control part, elastomeric blister actuator part, drug inlet and outlet. Expanded elastomeric blister actuator continuously pushes liquid in the chamber to outlet. At same time, microchannel diameter near the outlet was controlled by thin elastomeric membrane in hydraulic resistance control part. Eventually flow rate of infused liquid is controlled by air pressure. In experimental study, the amount of the filled liquid in the blister is precisely controlled by the height of the blister. Flow rate of infused liquid could be controlled, that is, controlled release of the drug over time was possible by adjusting hydraulic resistance and restoring pressure with the blister actuator.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1929-1931
• /
• 2003

본 연구에서 제안하는 마이크로 밸브는 열공압 방식으로 구동되고 제작비용이 저렴한 indium tin oxide (ITO) 및 polydimethylsiloxane (PDMS)로 제작되었다. 제안된 마이크로 밸브의 구조는 ITO 히터, SU-8 층, PDMS membrane, 그리고 PDMS 채널로 구성되어 있다. 제작된 열공압 구동기의 PDMS membrane의 변위는 현미경의 초점 거리의 변화로 측정하였으며 히터에 160mW 전력 인가 시 변위는 대략 $132{\mu}m$이다. 마이크로 밸브의 히터에 인가 전력에 따른 유량측정은 DI water를 사용하여 측정하였고 inlet 압력은 1.2kpa를 인가하여 측정하였다. 히터 인가 전력이 영일 경우 채널 폭이 $200{\mu}m$와 $400{\mu}m$인 마이크로 밸브의 유량은 각각 대략 $36{\mu}{\el}$/min과 $110{\mu}{\el}$/min 이었다. 채널 폭이 $200{\mu}m$와 $400{\mu}m$인 마이크로 밸브의 유량은 히터 인가 전력이 각각 70mW와 160mW에서 영이 되었다.

• 설비공학논문집
• /
• 제17권7호
• /
• pp.642-648
• /
• 2005

This study has been conducted to investigate the thermopneumatic and flow characteristics of diffuser/nozzle based thermopneumatic micropumps. In this study, a transient three-dimensional numerical analysis using FSI (Fluid-Structure Interaction) model has been employed to analyze the effects of the interaction between the membrane and two fluids (air and water) in the thermopneumtic micropump. The transient temperature and pressure in the cavity, the transient displacements of the membrane and the net flow rate of the micropump have been closely calculated for the frequency of 1 Hz. It has been found that the difference of the flow rates at the inlet and outlet is larger in the cooling period than in the heating period and that the duty ratio is very important in association with pump performance because the temperature in the cavity ascends drastically in the heating period and descends slowly in the cooling period. This study can be regarded as fundamental understandings for the design and analysis of thermopneumatic micropumps.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.191-195
• /
• 2007

In this study, we estimated the performance of PEMFC's unit cell as changing operating temperature in different inlet humidity condition at cathode side but anode dry, and tried to match experimental results with 1-dimensional simulation. We used $Nafion^{\circledR}112$ membrane and a self-manufactured PEMFC with active area of $25cm^{2}$ was used in this study. The range of operating temperature was $40{\sim}70^{\circ}C$ and oxygen through bubbled humidity chamber was supplied $0{\sim}80$% humidity condition as changing water temperature in humidity chamber. For figuring out governing equations, represent water contents in electrolyte membrane, the linear forward difference method was applied about time progress and quadratic central difference method was used about space progress. It was assumed that pressure terms were linearly changed due to thin electrolyte membrane. In low operating temperature condition, $40{\sim}60^{\circ}C$, increasing temperature rarely effected cell performance but we can see performance drop at $70^{\circ}C$. By modifying Henrry's constant and/or diffusion coefficient, the modified one-dimensional model was accomplished for calculation.

• Journal of Mechanical Science and Technology
• /
• 제17권9호
• /
• pp.1358-1370
• /
• 2003

The effects of anode, cathode, and cooling channels for a Proton Exchange Membrane Fuel Cell (PEMFC) on flow fields have been investigated numerically. Continuous open-faced fluid flow channels formed in the surface of the bipolar plates traverse the central area of the plate surface in a plurality of passes such as a serpentine manner. The pressure distributions and velocity profiles of the hydrogen, air and water channels on bipolar plates of the PEMFC are analyzed using a two-dimensional simulation. The conservation equations of mass, momentum, and energy in the three-dimensional flow solver are modified to include electro-chemical characteristics of the fuel cell. In our three-dimensional numerical simulations, the operation of electro-chemical in Membrane Electrolyte Assembly (MEA) is assumed to be steady-state, involving multi-species. Supplied gases are consumed by chemical reaction. The distributions of oxygen and hydrogen concentration with constant humidity are calculated. The concentration of hydrogen is the highest at the center region of the active area, while the concentration of oxygen is the highest at the inlet region. The flow and thermal profiles are evaluated to determine the flow patterns of gas supplied and cooling plates for an optimal fuel cell stack design.

• 드라이브 ㆍ 컨트롤
• /
• 제16권2호
• /
• pp.51-58
• /
• 2019

In this study, flow analysis and dehumidification experiment were conducted on hollow fiber membrane module to determine the dehumidification characteristics of its various configurations. A quantitative analysis of the CFD for four different models with a temperature of $30^{\circ}C$ and 30%RH inlet humidity was conducted. Each model has different shape parameters i.e. the number of hollow fiber membranes and the presence or absence of baffles. After comparison between the flow analysis results and dehumidification experiment results, the percentage error was found to be approximately 2%. The moisture removal rate for each model was calculated using flow analysis data. It was found that the moisture removal rate of refined model with three baffles and eight hollow fiber membranes was highest among the four modeled modules of hollow fiber membrane one, i.e. about 60%.

• 멤브레인
• /
• 제29권5호
• /
• pp.284-291
• /
• 2019

본 연구에서는 대면적을 지니는 CDI 모듈의 흐름 향상을 위하여 유체가 들어가는 유입구로부터 면적이 증가하는 직사각형 형태의 유로를 설계하였다. 이를 바탕으로 설계된 모듈 형태에 대해 공급수의 흐름성과 사영역의 유무를 파악하였고 CFD 전산 유체 역학 프로그램을 통해 유로 내의 내부 압력, 유선 그리고 속도 벡터 분포를 분석하였으며 실제 흐름 관측과 CFD 프로그램을 비교 분석하였다. 실험 결과 모든 유속 10, 20, 30 mL/min에서 유로 내 사영역이 거의 발생하지 않았으며 공급수의 흐름성도 일정하게 유지되어 추후 대면적을 가지는 CDI 공정에 적용이 가능할 것이라 판단된다.

• Korean Chemical Engineering Research
• /
• 제50권4호
• /
• pp.738-742
• /
• 2012

본 연구에서는 알루미나 나노 템플레이트(anodic alumina oxide; AAO)를 이용하여 신속하면서도 효과적으로 나노입자 및 바이오물질을 분리, 농축할 수 있는 나노필터 소자를 개발하였다. 본 연구에서 사용한 나노필터 소자는 유체의 주입 및 흐름이 가능한 미세유체채널(microfluidic channel)을 PDMS에 패터닝하였다. 위아래로 형성된 PDMS 미세유체채널 사이로, 다양한 크기의 나노 다공을 형성하고 있는 AAO 막을 삽입하여 크기에 따른 나노입자 및 바이오 물질을 분리할 수 있었다. 위아래로 PDMS 유체채널과 AAO 분리막을 집적하고, 최종적으로 아크릴레이트 플락스틱(acrylic plastic)으로 전체 소자를 고정하여 나노필터유체소자를 제작하였다. 완성된 나노필터소자를 이용하여 나노입자의 농축효율 및 은나노입자가 뭉쳐져있는 필터존(filtration zone)으로부터 뎅기 바이러스(dengue virus)를 표면증강라만(surface enhanced Raman scattering)분석법에 의해 검출할 수 있었다.