• Wind and Structures
• /
• v.36 no.3
• /
• pp.149-160
• /
• 2023

Lightness and flexibility of membrane roofs make them very sensitive to any external load. One of the most important parameters that controls their behavior, especially under wind load is the sag/span ratio of edge cables. Based on the value of the pretension force in the edge cables and the horizontal projection of the actual area covered by the membrane, an optimized design range of cable sag/span ratios has been determined through carrying on several membrane form-finding analyses. Fully coupled fluid structure dynamic analyses of these membrane roofs are performed under wind load with several conditions using the CFD method. Through investigating the numerical results of these analyses, the behavior of membrane roofs with cables sag/span ratios selected from the previously determined optimized design range has been evaluated.

• Journal of Korean Association for Spatial Structures
• /
• v.2 no.2 s.4
• /
• pp.11-15
• /
• 2002

Formerly, it was called a tent and now, it is called membrane structure. If saying a tent, it imagines the tent of Bedouin, Mongolia and North American Indian. It became clear from the excavated wall painting that have been covered with the retractable roof of the canvas on the auditorium at the amphitheater in Pompeii and became a topic. These tents were made of the animal skins or fabric woven with the flax plants, and these tents are still used. However, if saying membrane material at present, it says the one to have applied a coating resin to the textile. Because the base fabric of membrane material is a woven fabric, the relation between the stress and the strain is different to the direction of the weaving thread. Moreover, the tensile force must always occur in the membrane surface. From these reasons, because the membrane structure corresponds to the particular building material and the construction method about the Building Standard Law, it must be examined specially that the membrane structural building have the same or any more safety as the provisions which was set to the Building Standard Law. Therefore, the technical standards about the membrane structural building became indispensable. In the paper, the kinds of the membrane materials, which are used for the membrane structural buildings, and technical standards process of the creating for the membrane structure buildings are introduced. Lastly, some of the soccer stadiums for 2002 FIFA World Cup KOREA/JAPAN which be covered with the roof of the membrane structures are presented.

• Advances in Computational Design
• /
• v.2 no.1
• /
• pp.71-87
• /
• 2017

This study focuses on the efficiency and applicability of dynamic relaxation methods in form-finding of membrane structures. Membrane structures have large deformations that require complex nonlinear analysis. The first step of analysis of these structures is the form-finding process including a geometrically nonlinear analysis. Several numerical methods for form-finding have been introduced such as the dynamic relaxation, force density method, particle spring systems and the updated reference strategy. In the present study, dynamic relaxation method (DRM) is investigated. The dynamic relaxation method is an iterative process that is used for the static equilibrium analysis of geometrically nonlinear problems. Five different examples are used in this paper. To achieve the grading of the different dynamic relaxation methods in form-finding of membrane structures, a performance index is introduced. The results indicate that viscous damping methods show better performance than kinetic damping in finding the shapes of membrane structures.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.3
• /
• pp.116-120
• /
• 2013

This paper proposes a novel RF MEMS dc-contact switch with stiff membrane on a quartz substrate. The uniqueness of this work lies in the utilization of a seesaw mechanism to restore the movable part to its rest position. The switching action is done by using separate pull-down and pull-up electrodes, and hence operation of the switch does not rely on the elastic recovery force of the membrane. One of the main problems faced by electrostatically actuated MEMS switches is the high operational voltages, which results from bending of the membrane, due to internal stress gradient. This is resolved by using a stiff and thick membrane. This membrane consists of flexible meanders, for easy movement between the two states. The device operates with an actuation voltage of 6.43 V, an insertion loss of -0.047 dB and isolation of -51.82 dB at 2 GHz.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.433-437
• /
• 2006

Pt/Nafion self-humidifying membranes for Polymer Electrolyte Membrane Fuel Cell(PEMFC) were synthesized via supercritical-impregnation methods. The Nafion 112 membranes were impregnated with Pt(II)$(acetylacetonate)_2$ from a supercritical carbon dioxide $(scCO_2)$ solution at $80^{\circ}C$ and 30MPa. After the impregnation, the pressure decreased slowly by releasing $CO_2$. And the Pt-impregnated Nafion membrane was converted Pt deposited Nafion membrane by reducing agent, sodium borohydride $(NaBH_4)$ with various concentrations under $50^{\circ}C$ and 2 hours. The prepared Pt-impregnated Nafion (Pt/Nafion) composite membrane were investigated by Electron Prove Micro analysis (EPMA) and X-rat Diffraction analysis (XRD) which showed distribution of Pt particle and Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) a which revealed morphology of surface of Pt/Nafion composite membrane. The performance of the Pt/Nafion 112 membranes was examined in PEMFC as aself-humidifyin membranes using purpose-built equipment.

• Journal of the Korean Institute of Gas
• /
• v.6 no.4 s.18
• /
• pp.47-52
• /
• 2002

Analytical studies have been performed to investigate the strength of the membrane and the reaction force at the anchor point. Using nonlinear FEM code and experiments, the stress analysis of the corrugated membrane related the cryogenic liquid pressure and thermal loading is performed to ensure the stability and fatigue strength of the membrane. This paper reports on the FEM results of membrane.

• Membrane and Water Treatment
• /
• v.3 no.4
• /
• pp.231-242
• /
• 2012

The performance of a nanofiltration membrane for treatment of a low-level radioactive liquid waste was investigated through static and dynamic tests. The liquid waste ("carbonated water") was obtained during conversion of $UF_6$ to $UO_2$. In the static tests membrane samples were immersed in the waste for 24, 48 or 72 h. The transport properties of the samples (hydraulic permeability, permeate flow, selectivity) were evaluated before and after immersion in the waste. In the dynamic tests the waste was permeated in a permeation flow front system under 0.5 MPa, to determine the selectivity of NF membranes to uranium. The surface layer of the membrane was characterized by zeta potential, field emission microscopy, atomic force spectroscopy and infrared spectroscopy. The static test showed that the pore size distribution of the selective layer was altered, but the membrane surface charge was not significantly changed. 99% of uranium was rejected after the dynamic tests.

• Membrane Journal
• /
• v.28 no.6
• /
• pp.388-394
• /
• 2018

Carbon nanotube (CNT) based membranes are promising candidates for separation membranes by showing high water transport rate and ion rejection rate according to their radii. The ion selectivity is an important factor to discover the full potential of CNT membranes, and it is affected by the functionalization of CNTs. With multivalent/size ion mixtures, the ion selectivity is affected by not only ion-functional groups interaction but also ion-ion interactions and ion size exclusion in a complex manner. In this study, molecular dynamics simulations are performed to study the ion selectivity of functionalized carbon nanotubes when multivalent/size ions are contained. The permeation energy barriers are calculated by plotting potential of mean force profiles, and various factors, such as CNT size and partial charges, affecting ion selectivity are investigated. The results presented here will be useful for designing CNT membranes for ion separation, biomimetic ion channels, etc.

• Membrane and Water Treatment
• /
• v.7 no.4
• /
• pp.355-365
• /
• 2016

The improvement of fouling resistance of porous polymeric membrane is one of the most important targets in membrane preparation for water purification in many process like wastewater treatment. Membranes can be modified by various techniques, including the treatment of polymer material, blending of hydrophilic polymer into polymer solution, and post treatment of fabricated membrane. This research proposed the modifications of morphology and surface property of hydrophobic membrane by blending polyethersulfone (PES) with three polymeric additives, polyvinylpyrrolidone (PVP), Pluronic F127 (Plu), and Tetronic 1307 (Tet). PES hollow fiber membranes were fabricated via dry-wet spinning process by using a spinneret with inner and outer diameter of 0.7 and 1.0 mm, respectively. The morphology changes of PES blend membrane by those additives, as well as the change of performance in ultrafiltration module were comparatively observed. The surface structure of membranes was characterized by atomic force microscopy and Fourier transform infra red spectroscopy. The cross section morphology of PES blend hollow fiber membranes was investigated by scanning electron microscopy. The results showed that all polymeric additives blended in this system affected to improve the performances of PES membrane. The ultra-filtration experiment confirmed that PES-PVP membrane showed the best performance among the three membranes on the basis of filtration stability.

• Membrane and Water Treatment
• /
• v.7 no.5
• /
• pp.377-401
• /
• 2016

To study the effect of titanium dioxide ($TiO_2$) nanoparticles on membrane performance and structure and to explore possible improvement of using mixed solvents in the casting solution, composite polyvinylidene fluoride (PVDF) ultrafiltration membranes were prepared via immersion precipitation method using a mixture of two solvents triethyl phosphate (TEP) and dimethylacetamide (DMAc) and addition of $TiO_2$ nanoparticles. Properties of the neat and composite membranes were characterized using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), Atomic force microscopy (AFM) and contact angle and membrane porosity measurements. The neat and composite membranes were further investigated in terms of BSA rejection and flux decline in cross flow filtration experiments. Following hydrophilicity improvement of the PVDF membrane by addition of 0.25 wt.% $TiO_2$, (from $70.53^{\circ}$ to $60.5^{\circ}$) degree of flux decline due to irreversible fouling resistance of the composite membrane reduced significantly and the flux recovery ratio (FRR) of 96.85% was obtained. The results showed that using mixed solvents (DMAc/TEP) with lower content of $TiO_2$ nanoparticles (0.25 wt.%) affected the sedimentation rate of nanoparticles and consequently the distribution of nanoparticles in the casting solution and membrane formation which influenced the properties of the ultimate composite membranes.