• Journal of Welding and Joining
• /
• 제23권3호
• /
• pp.61-67
• /
• 2005

Since lead (Pb)-free solders for electronics have higher melting points than that of eutectic Sn-Pb solder, they need higher soldering temperatures. In order to decrease the soldering temperature we tried to coat Sn-Bi layer on $Sn-3.5\%Ag$ solder by electroplating, which applies the mechanism of transient liquid phase bonding to soldering. During heating Bi will diffuse into the $Sn-3.5\%Ag$ solder and this results in decreasing soldering temperature. As bonding samples, the 1608 capacitor electroplated with Sn, and PCB, its surface was finished with electroless-plated Ni/Au, were selected. The $Sn-95.7\%Bi$ coated Sn-3.5Ag was supplied as a solder between the capacitor and PCB land. The samples were reflowed at $220^{\circ}C$, which was lower than that of normal reflow temperature, $240\~250^{\circ}C$, for the Pb-free. As experimental result, the joint of $Sn-95.7\%Bi$ coated Sn-3.5Ag showed high shear strength. In the as-reflowed state, the shear strength of the coated solder showed 58.8N, whereas those of commercial ones were 37.2N (Sn-37Pb), 31.4N (Sn-3Ag-0.5Cu), and 40.2N (Sn-8Zn-3Bi). After thermal shock of 1000 cycles between $-40^{\circ}C$ and $+125^{\circ}C$, shear strength of the coated solder showed 56.8N, whereas the previous commercial solders were in the range of 32.3N and 45.1N. As the microstructures, in the solder $Ag_3Sn$ intermetallic compound (IMC), and along the bonded interface $Ni_3Sn_4$ IMC were observed.

• 한국결정성장학회지
• /
• 제26권4호
• /
• pp.150-154
• /
• 2016

$K_2Ti_6O_{13}$ 휘스커를 합성하는 방법은 고상법, 수열합성법, 소성법, 융제법, 서냉법, 용융법, KDC법, 졸-겔법 등이 있다. 융제법을 이용하여 $K_2Ti_6O_{13}$을 합성하는 연구를 진행하였다. 칼륨 전구체의 종류와 반응온도와 시간을 조절하여 합성 된 $K_2Ti_6O_{13}$의 입자크기와 분포를 제어하였고, 합성된 $K_2Ti_6O_{13}$의 평균입자 크기는 $500nm{\sim}2{\mu}m$였다. KOH와 $TiO_2$의 비율, pH(KOH 첨가량), 반응온도와 반응시간 등의 공정변수에 대해 연구를 진행하였다. 합성된 $K_2Ti_6O_{13}$은 X-선 회절분석기와 전계방사 주사전자현미경을 이용하여 특성평가를 실시하였다.

• 한국세라믹학회지
• /
• 제46권6호
• /
• pp.587-591
• /
• 2009

Lithium salt have been used mainly as electrolyte of thermal battery for electricity storage. Recently, The 3phase lithium salt(LiCl-LiF-LiBr) is tried to use as electrolyte of thermal battery for high electric power. It is reported that LiCl-LiF-LiBr salt have high ion mobility due to its high lithium ion concentration. Solid lithium salt is melt to liquid state at above $500{^{\circ}C}$. The lithium ion is easily reacted with support materials. Because the melted lithium ion has small ion size and high ion mobility. For the increasing mechanical strength of electrolyte pellet, the research was started to apply ceramic filter to support of electrolyte. In this study, authors used SiOC web and glass fiber filter as ceramic mat for support of electrolyte and impregnated LiCl-LiF-LiBr salt into ceramic mat at above $500{^{\circ}C}$. The fabricated electrolyte using ceramic mat was washed with distilled water for removing lithium salt on ceramic mat. The washed ceramic mat was observed for lithium ion reaction behavior with XRD, SEM-EDS and so on.

• Tribology and Lubricants
• /
• 제32권5호
• /
• pp.141-146
• /
• 2016

The diketopyrrolopyrrole (DPP) pigment is a bicyclic 8-π-electron system containing two lactam units. Typical DPP derivative pigments have melting points of over 350°C and very low solubility in most solvents, and show absorption in the visible region with a molar extinction coefficient of 33,000 dm²mol⁻¹ and strong photoluminescence with maxima in the range 500–600 nm. X-ray structure analyses of DPP show that the whole molecule is almost in one plane. The phenyl rings are twisted out of the heterocyclic plane and the intermolecular hydrogen bonding between neighboring lactam NH and carbonyl units influences the structure of the DPP pigment in the solid state. In this study, mono-N-alkylation and mono-N-arylation were undertaken for Pigment Red 264 or Pigment Orange 73 with alkyl halide and aryl halide, respectively, in the presence of sodium tert-butoxide as a base catalyst to improve the solubility of DPP pigments and their application as CO₂ indicators. The synthetic yield was in the range 11–88%. The indicator dyes are highly soluble in organic solvents and shows pH-dependent absorption (λ_max 501 and 572 nm for the protonated and deprotonated forms, respectively) and emission (λ_max 524 and 605 nm for the protonated and deprotonated forms, respectively) spectra. The mono-N-alkylated and mono-N-arylated DPP pigment was identified by ¹H-NMR (¹H-Nuclear Magnetic Resonance Spectrometer), FT-IR (Fourier Transform Infrared Spectroscopy), and MS (Mass Spectrometry). According to the results of color and hue properties obtained by a color matching analyzer, the synthesized DPP pigment material can be used as a CO₂ indicator.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1998년도 제14회 학술발표회 논문개요집
• /
• pp.135-136
• /
• 1998

By the ion bombardment the original discrete layered structure is damaged and a uniformly mixed layer is formed by the intermixing of the films. Immediately after this dynamic cascade mixing a structure of this mixed layer is likely to be a mixture of randomly distributed atoms. Subsequently the mixed layered structure becomes a non-equilibrium structure such as the metastable pphase because the kinetic energies of the incident ions rappidly dissippate and host atoms within the collision cascade region are quenched from a highly energetic state. The formation of the metastable transition metal alloys using ion-beam-mixing has been extensively studied for many years because of their sppecific ppropperties that differ from those of bulk materials. in ion-beam-mixing the alloy or comppound is formed due to the atomic interaction between different sppecies during ion bombardment. in this study the metastable pphase formed by ion-beam-mixing pprocess is comppared with equilibrium one by arc-melting method by GXRD and XAS. Therfore we studied the fundamental characteristics of charge redistribution uppon alloying and formation of intermetallic comppounds. The multi-layer films were depposited on a wet-oxidized Si(100) substrate by sequential electron beam evapporation at a ppressure of less than 5$\times$10-7 Torr during depposition. These compprise 4 ppairs of Co and ppt layers where thicknesses of each layer were varied in order to change the alloy compposition.

• 한국재료학회지
• /
• 제22권5호
• /
• pp.243-248
• /
• 2012

ZrN nanoparticles were prepared by an exothermic reduction of $ZrCl_4$ with $NaN_3$ in the presence of NaCl flux in a nitrogen atmosphere. Using a solid-state combustion approach, we have demonstrated that the zirconium nitride nanoparticles synthesis process can be completed in only several minutes compared with a few hours for previous synthesis approaches. The chemistry of the combustion process is not complex and is based on a metathesis reaction between $ZrCl_4$ and $NaN_3$. Because of the low melting and boiling points of the raw materials it was possible to synthesize the ZrN phase at low combustion temperatures. It was shown that the combustion temperature and the size of the particles can be readily controlled by tuning the concentration of the NaCl flux. The results show that an increase in the NaCl concentration (from 2 to 13 M) results in a temperature decrease from 1280 to $750^{\circ}C$. ZrN nanoparticles have a high surface area (50-70 $m^2/g$), narrow pore size distribution, and nano-particle size between 10 and 30 nm. The activation energy, which can be extracted from the experimental combustion temperature data, is: E = 20 kcal/mol. The method reported here is self-sustaining, rapid, and can be scaled up for a large scale production of a transition metal nitride nanoparticle system (TiN, TaN, HfN, etc.) with suitable halide salts and alkali metal azide.

• 한국식생활문화학회지
• /
• 제9권2호
• /
• pp.131-136
• /
• 1994

한국산 씀바귀(Lactuca dentata Makino)의 ethylacetate 추출물에서 6 종류의 flavonoid 성분이 TLC에 의해서 검출 되었으며, 이들은 극성에 따라서 A에서 F가지 명명되었다. 그들 중 주성분으로 생각되는 물질 E를 column chromatography을 이용하여 분리정제 하였다. 물질 E의 녹는 점은 $249.5^{\circ}C-251^{\circ}C$ 로 나타났으며, 그 구조를 밝히기 위하여, 물질 E와 이를 가수분해한 genin에 대한 여러가지 shift reagent에서 UV와 IR분석을 하고 또한 물질 E와 그의 acetyl 유도체에 대한 NMR 분석을 하였으며 물질 E에 결합된 당은 TLC에 의하여 확인하였다. 이와같은 분석 결과에서 물질 E는 luteolin 모핵에 glucose가 결합된 $luteolin-7-0-{\beta}-D-glucoside$로서 확인되었다.

• 한국전기전자재료학회논문지
• /
• 제13권4호
• /
• pp.349-358
• /
• 2000

Fabrication and Characterization of Bi$_{2}$/Sr$_{2}$/CaCu$_{2}$/O$_{8}$(Bi2212) superconductor thick films were fabricated successfully on C tapes by liquid reaction between Cu-free precursors of Bi$_{x}$/SrCaO/$_{y}$(x=1.2-2) and Cu tapes. Cu-free Bi-Sr-Ca-O powder mixtures were screen-printed on Cu tapes and heat-treated at 850-87$0^{\circ}C$ for several minutes in air oxygen nitrogen and low oxygen pressure. In order to obtain the optimum heat-treatment condition we studied the effect of the precursor composition the printing thickness and the heat-treatment atmosphere on the superconducting properties of Bi2212 films and the reaction mechanism. Microstructures and phases of thick films were analyzed by films and the reaction mechanism. Microstructures and phases of thick films were analyzed by optical microscope and XRD. The electric properties of superonducting films were examined by the four probe method. At heat-treatment temperature the thick films were in a partially molten state by liquid reaction between CuO of the oxidized copper tape and the precursors which were printed on Cu tapes. During the heat-treatment procedure Bi2212 superconducting particle nucleate and grow in preferred orientations.ons.s.

• Bulletin of the Korean Chemical Society
• /
• 제25권8호
• /
• pp.1171-1176
• /
• 2004

Three banana-shaped achiral compounds, 4-chloro-1,3-phenylene bis [4-{4-(undecenyloxy)phenyl imino-methyl} benzoate] derivatives, were synthesized with variation of a substituent (x=H, F, Cl); their antiferro-electric properties are described. The smectic mesophases, including a switchable chiral smectic C(Sm $C^{\ast}$) phase, were characterized by differential scanning calorimetry, polarizing optical microscopy, triangular wave method, and X-ray diffractometry. The presence of vinyl groups at the terminals of linear side wings in the banana-shaped achiral molecules induced a decrease in melting temperature and formation of the switchable Sm $C^{\ast}$ phase in the melt. The smectic phase having a lateral fluorine-substituent at 3-position of the Schiff's base moiety showed antiferroelctric switching, and the value of spontaneous polarization on reversal of an applied electric field was 250 nC/$cm^2$ .

• Elastomers and Composites
• /
• 제48권1호
• /
• pp.18-23
• /
• 2013

용융상태에서 nylon 12 elastomer에 소량의 dicumyl peroxide (DCP) 와 triallyl cyanuate (TAC)를 첨가하여 nylon 12 elastomer를 부분적으로 가교시켰으며, 이에 따른 nylon 12 elastomer의 기계적, 동적기계적 그리고 유변학적 특성을 tensile test, DMA, small amplitude oscillating rheometer를 이용하여 각각 알아보았다. TAC의 함량이 증가함에 따라 인장탄성률과 영률은 증가하고, 파단신율은 감소하였다. DMA 측정결과, DCP로 부분적으로 가교시킨 nylon 12 elastomer의 PTMG상의 유리전이온도는 순수한 nylon 12 elstomer에 비해 증가하였고, storage modulus는 nylon 12상의 용융온도 이상에서도 거의 일정한 값을 나타내었다. 부분적으로 가교시킴에 따른 유변학적 특성의 변화는 TAC의 함량이 증가함에 따라 solid like behavior와 shear thinning behavior가 점점 뚜렷하게 나타남을 알 수 있었다. 이로부터 nylon 12 elastomer를 용융상태에서 부분적으로 가교시킴으로써 용융가공성을 저하시키지 않으면서, 기계적 물성은 효과적으로 향상시킬 수 있었으며, 특히, nylon 12 elastomer의 사용가능 온도범위를 증가시킬 수 있었다.