• Journal of Welding and Joining
• /
• 제20권4호
• /
• pp.484-490
• /
• 2002

The formation and stability of stationary laser weld keyholes were investigated using a numerical simulation. The effect of multiple reflections in the keyhole was estimated using the ray tracing method, and the free surface profile, flow velocity and temperature distribution were calculated numerically. In the simulation, the keyhole was formed by the displacement of the melt induced by evaporation recoil pressure, while surface tension and hydrostatic pressure opposed cavity formation. A transition mode having the geometry of the conduction mode with keyhole formation occurred between the conduction and keyhole modes. At laser powers of 500W and greater, the protrusion occurred on the keyhole wall, which resulted in keyhole collapse and void formation at the bottom. Initiation of the protrusion was caused mainly by collision of upward and downward flows due to the pressure components, and Marangoni flow had minor effects on the flow patterns and keyhole stability.bility.

• 반도체디스플레이기술학회지
• /
• 제11권4호
• /
• pp.7-12
• /
• 2012

Extrusion is one of the most important operations in the polymer-processing industry. Development of models for extrusion and computer tools offer a route to developing reliable and optimized process designs. The models are based on the analysis of physical phenomena encountered during the process. Balance equations for mass, momentum and energy are fundamental to the problem. A predictive computer model has been developed for the single screw extruders with conventional screws of different geometry. The model takes into account melting zones of the extruder and describes an operation of the extruder system, making it possible to predict mass flow rate of the polymer, pressure and velocity profiles along the extruder screw channel. The simulation parameters are the material and rheological properties of the polymer; the screw pitch, and screw speed.

• Bulletin of the Korean Chemical Society
• /
• 제21권1호
• /
• pp.69-74
• /
• 2000

Applicability of Thermal field flow fractionation (ThFFF) was investigated for the analysis of masticated natural rubber (NR) adhesives produced bya hot melt mastication process. An optimum ThFFF condition for NR analysis was found by using tetrahydrofuran (THF) as a solvent/carrier and a field-programming. Low flowrate (0.3 mL/min) was used to avoid stopping the flow for the sample relaxation. Measured molecular weight distribution was used to monitor degradation of rubber during the mastication process. Rubber samples collected at three different stages of the mastication process and were analyzed by ThFFF. It was found that in an anaerobic process rubber degradation occurs at the resin-mixing (compounding) zone as well as in the initial break-down zone, while in an aerobic process most of degradation occurs at the initial breakdown zone. It was also found that E-beam radiation on NR causes a slight increase in the NR molecular weight due to the formation of a branched structure.

• 농촌계획
• /
• 제11권4호
• /
• pp.67-74
• /
• 2005

The Doam watershed is located at alpine areas and the annual average precipitation, including snow accumulation, is significant higher than other areas. Thus, pollutant laden runoff and sediment discharge from the alpine agricultural fields are causing water quality degradation at the Doam watershed. To estimate soil erosion from the agricultural fields, the Universal Soil Loss Equation (USLE) has been widely used because of its simplicity to use. In the early spring at the Doam watershed, the stream flow increases because of snow melt, which results in erosion of loosened soil experiencing freezing and thaw during the winter. Also, extremely torrential rainfall, such as the typhoons 'RUSA' in 2002 and 'MAEMI' in 2003, caused significant amounts of soil erosion and sediment at the Doam watershed. However, the USLE model cannot simulate impacts on soil erosion of freezing and thaw of the soil. It cannot estimate sediment yield from a single torrential rainfall event. Also, it cannot simulate temporal changes in USLE input parameters. Thus, the Soil and Water Assessment Tool (SWAT) model was investigated for its applicability to estimate soil erosion at the Doam watershed, instead of the widely used USLE model. The SWAT hydrology and erosion/sediment components were validated after calibration of the hydrologic component. The R$^2$ and Nash-Sutcliffe coefficient values are higher enough, thus it is found the SWAT model can be efficiently used to simulate hydrology and sediment yield at the Doam watershed. The effects of snow melt on SWAT estimated stream flow and sediment were investigated using long-term precipitation and temperature data at the Doam watershed. It was found significant amount of flow and sediment in the spring are contributed by melting snow accumulated during the winter. Two typhoons in 2002 and 2003, MAEMI and RUSA, caused 33% and 22% of total sediment yields at the Doam watershed, respectively. Thus, it is recommended that the SWAT model, capable of simulating snow melt, sediment yield from a single storm event, and long-term weather data, needs to be used in estimating soil erosion at alpine agricultural areas to develop successful soil erosion management instead of the USLE.

• 한국산업안전학회:학술대회논문집
• /
• 한국안전학회 2002년도 추계 학술논문발표회 논문집
• /
• pp.166-171
• /
• 2002

폐자원의 재활용은 현재 미래산업을 발전시키는데 중요한 변수로 작용하고 있으며, 폐플라스틱의 경우 통신 케이블 덕트, 고속전철용 케이블 덕트, 선박용 구조체등 고부가가치 제품으로의 기술개발이 활발히 진행되고 있다. 폐 Polyolefin 계열의 수지는 성형가공이 적절한 MFI(Melt flow index)와 뛰어난 기계적 물성, 가공 성형성 등으로 인해 다양한 형태와 용도로 recycling되고 있으나, 재생시 다수 Grade에 의한 분별, 분리수거의 어려움, 상용성결여, 난연성 부재 그리고 70% 대의 기계적 물성 회복율로 인해 그 용도가 제한되고 있는 실정이다.(중략)

• 한국막학회:학술대회논문집
• /
• 한국막학회 1997년도 추계 총회 및 학술발표회
• /
• pp.90-93
• /
• 1997

1. 서론 : 본 연구에서는 수처리용으로 사용되는 PE 중공사 분리막을 HDPE/LP 혼합계의 열유도 상분리법을 이용하여 제조하고 PE의 MPR(Melt Flow Rate), 희석제 함량, 방사조건 등이 중공사 분리막의 물성변화에 미치는 영향을 투수 계수를 중심으로 검토하였다.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 1998년도 봄 학술발표회 논문집
• /
• pp.14-19
• /
• 1998

Increasing demand for high modulus high strength polymeric materials have drawn considerable interest in industry. Thermotropic liquid crystal polymers (TLCP), differing from lyotropic liquid crystal polymers, have excellent melt processability and mechanical property resulting from the high degree of molecular orientation under a shear flow field in the molten state with relatively low viscosity$\^$1,2/.(omitted)

• 유변학
• /
• 제2권1호
• /
• pp.27-32
• /
• 1990

본 연구에서는 전선피복 die 내고분자 물질의 이동현상에 관한여 Carreau model을 도입하여 유한요소법으로 수치해석을 수행하였다. Polyvinyl chloride(PVC)의 유변상수들의 변화가 유동에 미치는 영향을 조사하였고 온도에 따른 점도의 변화를 고려한 비등온 조건 및 전선피복 공정에서 발생할 수 있는 slip 경계조건을 적용시킨 경우에 대한 수치모사도 수행하였다.

• 한국세라믹학회지
• /
• 제23권1호
• /
• pp.21-26
• /
• 1986

By the floating zone method with infrared radiation convergence type heater homogeneously $Cr^{3+}$ doped alu-mina single crystal was obtained. And sizx {1010} facets appeared at the surface of [0001] grown crystals. $ZrO_2$ and $HfO_2$ precipitated as secondary phase and were not doped in the crystals. We found that the dist-ribution of the secondary phase which was mainly located at the surface and the peripheral region was closely related to the flow pattern of melt zone.

• 한국세라믹학회지
• /
• 제25권1호
• /
• pp.78-82
• /
• 1988

Good quality LiNbO3 single crystals which can be applied to SAW devices, were grown by Czochralski method. It was observed that the gas-bubbles were concentrated in ring shape at the outer part of grown crystals, and this anomaly was illustrated by modeling the mechanism of gas-bubble entrapment according to the melt flow pattern in the crucible. And this mechanism was also encertained by observation of solid-liquid interface shape of grown crystals. The optimal condition for good quality crystals was known that the solid-liquid interface shape was slightly concave.