• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.768-773
• /
• 2009

Measuring method being applied for off-shore works is performed by using data logger or manual measuring instrument with wiring the cable connected from the sensor up to the position where measuring is allowed.(upper part of embankment or marine structure) Measuring management by using existing measuring method may be acceptable on the condition that the ground deformation volume(vertical, horizontal) is generally minimal and the site condition is good. But loss of measuring instrument, sensor cable failure or cutting is taken place frequently due to significant change of ground behavior caused by an external force change(embankment, excavation) under very soft ground condition(N value below 0-4). In case of the marine works, in particular, loss rate of measuring instrument is highly represented due to the factors of working barge anchoring, constructional interference and natural disaster. In order to solve these problems, measuring management was performed with employing underground wireless system at the immersed tunnel site. Measuring data was obtained freely under the marine environment by using underground wireless communication and cable cutting potential by ground behavior could be reduced. Measuring cost savings and its installation convenience were maximized by way of off-shore tower installation or cabling and by minimizing constructional interference of off-shore working barge. This case of measuring management was accomplished successfully.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.86.6-86
• /
• 2002

This work presents a study on development of a practical and quantitative technique for assessment of the healthy state of a structure by piezoelectric impedance-based technique associated with longitudinal wave propagation measuring method. A truss structure embedded with piezoelectric patches is investigated for a fundamental study on estimation of the looseness of bolts in the joint. In order to evaluate the minute mechanical impedance change due to loosening bolt, a harmonic longitudinal elastic wave is applied to the structure by a pair of PZT patches and their electric impedance is measured simultaneously. According to the experimental results, the change of the electric impedance of P...

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.4
• /
• pp.151-158
• /
• 2005

An important component of a cooling tower is an axial fan, and there happens distortion in its shape which brings significant loss of efficiency. In this paper, a surface profile measuring system for large size axial fan of cooling towers is developed. A laser sensor is used as a measuring device and aluminum profiles and stepping motors are engaged into the system as frame structure and driving devices respectively. The measuring data are compared to the design data to compute the distortion of the axial fans. Two types of errors, axial and twist errors, are used to represent the precision of axial fan distortion. Genetic algorithm is used to solve the optimization problem during computing the precision. Results are displayed three dimensionally in a solid-modeler as well as 2-D drawings to help users find it with ease.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.925-928
• /
• 2003

In this paper, a precision measuring machine for large sized axial fans of cooling towers are developed. A laser sensor is used as a measuring device and aluminum profiles and stepping motors are engaged into the system as frame structure and driving devices respectively. 3-dimensional measuring data are compared to the design data to compute the distortion of the axial fans. Two distortions such as the axis of the fan and the airfoils along the axis are introduced to define the shape precision of axial fans. Genetic algorithm is used to solve the optimization problem during computing the distortion. Results of distortion are displayed 3 dimensionally in a solid-modeler as well as 2-D drawings to help users find it with case.

• Journal of Sensor Science and Technology
• /
• v.25 no.2
• /
• pp.110-115
• /
• 2016

This paper describes the design and fabrication of a three-axis force sensor with three parallel plate structures(PPSs) for measuring force in a finger force measuring system for a spherical object catch. The three-axis force sensor is composed of a Fx force sensor, Fy force sensor and a Fz force sensor, and the elements of Fx force sensor and Fy force sensor are a parallel plate structure(PPS) respectively and Fz force sensor is two PPS. The three-axis force sensor was designed using FEM(Finite Element Method), and manufactured using strain-gages. The characteristics test of the three-axis force sensor was carried out. As a test results, the interference error of the three-axis force sensor was less than 1.32%, the repeatability error of each sensor was less than 0.04%, and the non-linearity was less than 0.04%.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.293-294
• /
• 2006

The conventional strain measuring device is costly and complicated - it is not simple to understand its structure. Hence, strain gage and the A/D converter are assembled to come up with a load and a strain measuring device. The device was tested for measuring the strain in a loaded specimen and the experimental results were compared to those obtained by a commercial strain indicator.

• Journal of the Korea Safety Management & Science
• /
• v.10 no.1
• /
• pp.183-190
• /
• 2008

Measurement is a essential part in all kinds of industry, especially in manufacturing. But until now, measurement hasn't been located to the core of manufacturing in domestic. This study suggests improvement guide line for the multilateral problems of measuring instrument operation based on the investigation of small and medium-sized enterprises. To use measuring instrument correctly, man who treat it must be accustomed with the structure, the performance, the method. The measuring instrument must be corrected periodically. The correcting-schedule is established with environments with considering accuracy, stability, purpose, condition, and frequency.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.322-327
• /
• 2006

Banwol bridge with steel plate girder and Pyongtaek bridge with PSC bos girder have been operated maintenance measuring system by the Seoul-Chonan of Kyongbu express railway. By analyzing the theoretical and experimental values of design load for these two bridge, the establishment of reference maintenance for measuring items was deduced from research. Two materials, steel and concrete plates, were considered as the upper structure. Actual measurement data for the behavior under speed, structural analysis results, and the presented references were analyzed and used to set up the reference establishment. The measuring items are stress(strain), displacement, dynamic acceleration, expansion movement, and dynamic frequency. The maintenance reference was established by comparing analytical and measuring values of the five items with respect to structural state class.

• Journal of Industrial Convergence
• /
• v.6 no.2
• /
• pp.43-56
• /
• 2008

Measurement is used for evaluation of product or process exactly. If it couldn't measured correctly, Quality-cost must be raised and it would be hard to improve product quality. So, this study suggests improvement guide line for the multilateral problems of measuring instrument operation based on the investigation of 157 small and medium-sized enterprises in February, 2008. To use measuring instrument correctly, man who treat it must be accustomed with the structure, the performance, the method. The instrument is selected properly for the measurement goal. If not, results couldn't be correctly or wasted time, efforts, and costs. When selecting a instrument, the tolerance, the size, the figure, the material, and the efficiency must be considered. If the measuring instruments are controlled efficiently, it could be accomplished that improving product quality and coinciding with the goal of QM.

• International Journal of Aeronautical and Space Sciences
• /
• v.13 no.2
• /
• pp.221-228
• /
• 2012

An active compensation method for the deformation of composite structures using additional controllable metal parts is proposed, and its feasibility is experimentally investigated in a simulated space environment. Composite specimens are tested in a vacuum chamber, which is able to maintain pressure on the order of 10-3 torr and interior temperature in the range of ${\pm}30^{\circ}C$. The displacement-measuring interferometer system, which consists of a heterodyne HeNe laser and an interferometer, is used to measure the displacement of the whole structure. Meanwhile, the strain of the composite part and temperature of both parts are measured by fiber Bragg grating sensors and thermistors, respectively. The displacement of the composite structure is maintained within a tolerance of ${\pm}1{\mu}m$ by controlling the elongation of the metal part, which is bonded to the end of the composite part. Also, the possibility of fiber Bragg grating sensors as control input sensors is successfully demonstrated using a proper corrective factor based on the specimen temperature gradient data.