• 한국전자통신학회논문지
• /
• 제10권1호
• /
• pp.73-80
• /
• 2015

화학공장과 같이 위험지역에 설치된 밸브장치는 폭발의 위험을 방지하기 위해 방화 방폭장치로 밀폐되어 있다. 본 논문에서는 방폭장치로 인해 외부전원장치를 사용할 수 없는 밸브장치에 적외선센서와 Zigbee 센서를 이용하여 위험지역의 밸브의 열림도를 측정하여 개폐여부를 확인하고, 밸브 개폐 작동시간을 로그화하여 운전 관리자가 공장을 관리 통제할 수 있는 저전력 모니터링 시스템을 제안한다. 전력관리기능을 적용하기 위해 개선된 비동기LPL 알고리즘을 적용한 전력제어 릴레이보드를 개발하고, 이를 적용한 방폭형 지능형 밸브시스템과 공장 밸브 개폐모니터링 시스템을 설계하고 이를 구현 및 테스트 하였다.

• 한국항공우주학회지
• /
• 제33권12호
• /
• pp.48-53
• /
• 2005

본 논문에서 LIPCA(Lightweight Piezoceramic Composite Actuator)를 이용한 날갯짓(flapping) 기구의 개발에 관한 최근의 연구진척 사항을 제시하였다. 날갯짓 기구는 여러 개의 연결막대를 이용하여 LIPCA의 제한된 작동변위를 커다란 날갯짓 각(flapping angle)이 발생하도록 증폭시켰으며, 패더링 메커니즘(feathering mechanism)을 적용하여 날갯짓과 동시에 날개에 비틀림이 발생하도록 설계되었다. 이 날갯짓 기구의 고유 날갯짓 주파수는 약 9Hz로, 이때 최대의 날갯짓 각이 발생하였다. 제작된 날갯짓 기구의 작동성능을 평가하기 위하여 날갯짓 주파수를 4Hz에서 15Hz까지 변화시키면서 발생되는 양력과 추력을 측정하였으며, 최대 양력과 최대 추력은 고유 날갯짓 주파수 부근에서 계측되었다.

• 한국강구조학회 논문집
• /
• 제15권4호통권65호
• /
• pp.435-445
• /
• 2003

인장구조물에서의 인장재는 가장 중요한 부재임에도 불구하고, 현재 인장재에 발생하는 현장에서 효과적으로 측정하는 방법에는 어려운 점이 많다. 기존의 측정방법으로는 일시적 또는 특정부재의 측정은 가능하지만 전체부재의 측정과 장기간 측정은 불가능하다. 이에 인장재의 인장력을 측정하기 위한 방법을 제시하고, 인장력이 작용하였을 때 탄성상태에서 부재가 선형적으로 변형하는 성질을 이용하여 인장재의 인장력을 효과적으로 측정하기 위한 방법을 제시하였다. 또한 측정장치의 개발에 필요한 자료를 제공하고자 유한요소해석을 수행하였고, 시험체를 제작하여 실험을 실시하여 해석의 결과를 검증하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1494-1499
• /
• 2003

Kinematic calibration is a process whereby the actual values of geometric parameters are estimated so as to minimize the error in absolute positioning. Measuring all components of Cartesian posture, particularly the orientation, can be difficult. With partial pose measurements, all parameters may not be identifiable. This paper proposes a new device that can be used to identify all kinematic parameters with partial pose measurements. Study is performed for a six degree-of-freedom fully parallel Hexa Slide manipulator. The device, however, is general and can be used for other parallel manipulators. The proposed device consists of a link with U joints on both sides and is equipped with a rotary sensor and a biaxial inclinometer. When attached between the base and the mobile platform, the device restricts the end-effector's motion to five degree-of-freedom and can measure position of the end-effector and one of its rotations. Numerical analyses of the identification Jacobian reveal that all parameters are identifiable. Computer simulations show that the identification is robust for the errors in the initial guess and the measurement noise.

• 제어로봇시스템학회논문지
• /
• 제4권3호
• /
• pp.384-391
• /
• 1998

When a device is mounted on the PCB, it is impossible to have zero defects due to many unpredictable problems. Among these problems, devices with bent corner leads due to mis-handling and which are not placed at a given point measured along the axis are principal problem in SMT(Surface Mounting Technology). It is obvious that given the complexity of the inspection task, the efficiency of a human inspection is questionable. Thus, new technologies for inspection of SMD(Surface Mounting Device) should be explored. An example of such technologies is the Automated Visual Inspection(AVI), wherein the vision system plays a key role to correct this problem. In implementing vision system, high-speed and high-precision are indispensable for practical purposes. In this paper, a new algorithm based on the Radon transform which uses a projection technique to inspect the FIC(Flat Integrated Circuit) device is proposed. The proposed algorithm is compared with other algorithms by measuring the position error(center and angle) and the processing time for the device image, characterized by line scan camera.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제54권9호
• /
• pp.531-538
• /
• 2005

This paper proposes an expert system which is able to enhance the accuracy and productivity by determining the test strategy based on heuristic rules for test of the hybrid electronic circuit board producted massively in production line. The test heuristic rules are obtained from test system designer, test experts and experimental results. The guarding method separating the tested device with circumference circuit of the device is adopted to enhance the accuracy of measurements in the test of analog devices. This guarding method can reduce the error occurring due to the voltage drop in both the signal input line and the measuring line by utilizing heuristic rules considering the device impedance and the parallel impedance. Also, PSA(Parallel Signature Analysis) technique Is applied for test of the digital devices and circuits. In the PSA technique, the real-time test of the high integrated device is possible by minimizing the test time forcing n bit output stream from the tested device to LFSR continuously. It is implemented in Visual C++ computer language for the purpose of the implementation of the inference engine using the dynamic memory allocation technique, the interface with the electronic circuit database and the hardware direct control. Finally, the effectiveness of the builded expert system is proved by simulating the several faults occurring in the mounting process the electronic devices to the surface of PCB for a typical hybrid electronic board and by identifying the results.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권6호
• /
• pp.727-736
• /
• 1995

This paper examines the characteristics and physical properties of the scaled MONOS nonvolatile memory device for low programming voltage EEPROM. The capacitor-type MONOS memory devices with the nitride thicknesses ranging from 41.angs. to 600.angs. have been fabricated. As a result, the 5V-programmable MONOS device has been obtained with a 20ms programming time by scaling the nitride thickness to 57.angs. with a tunneling oxide thickness of 19.angs. and a blocking oxide thickness of 20.angs.. Measurement results of the quasi-static C-V curves indicate, after 10$\^$6/ write/erase cycles, that the devices are degraded due to the increase of the silicon-tunneling oxide interface traps. The 10-year retention is impossible for the device with a nitride less than 129.angs.. However, the MONOS memory device with 10-year retentivity has been obtained by increasing the blocking oxide thickness to 47.angs.. Also, the memory traps such as the nitride bulk trap and the blocking oxide-nitride interface trap have been investigated by measuring the maximum flatband voltage shift and analyzing through the best fitting method.

• Design & Manufacturing
• /
• 제14권4호
• /
• pp.25-39
• /
• 2020

In this study, an edge device that monitors the injection molding process by measuring the mold vibration(acceleration) signal and the mold surface temperature was developed and evaluated its performance. During injection molding, signals of the injection start, V/P switchover, and packing end sections were obtained through the measurement of the mold vibration and the injection time and packing time were calculated by using the difference between the times of the sections. Then, the mold closed and mold open signals were obtained using a magnetic hall sensor, and cycle time was calculated by using the time difference between the mold closed time each process. As a result of evaluating the performance by comparing the process data monitored by the edge device with the shot data recorded on the injection molding machine, the cycle time, injection time, and packing time showed very small error of 0.70±0.38%, 1.40±1.17%, and 0.69±0.82%, respectively, and the values close to the actual were monitored and the accuracy and reliability of the edge device were confirmed. In addition, it was confirmed that the mold surface temperature measured by the edge device was similar to the actual mold surface temperature.

• 열처리공학회지
• /
• 제34권1호
• /
• pp.25-30
• /
• 2021

The differential gear system is a device designed to distribute the driving force of both vehicle wheels and control the rotational speed when the vehicle turns on a curve. The differential device consists of a differential gear case, a ring gear, and a pressure ring. A differential pinion gear and side gear are mounted on the differential pinion shaft inside the differential gear case. In this study, a pin press-fitting device that mounts the pinier gear and side gear to the differential pinion shaft in the differential gear case was designed, and a jig device for pin press-fitting using servo press was developed. In addition, by precisely measuring the pin press-in load and press-in distance according to the pin hole diameter of the differential gear shaft, the optimization of the pin pressin process was established.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The Korea-Japan Plastics Processing Joint Seminar
• /
• pp.15-19
• /
• 2003

Polymeric micro lens arrays with diameters of $13\~96\;{\mu}m$ fabricated using the micro-compression molding with electro formed mold inserts. In the present study, the electro forming process was used to make the metallic micro-mold insert for micro-molding of microlens array. The wettability property of the fabricated mold insert was examined by measuring the contact angle of the polymer melt on the mold insert. Microlenses were compression-molded with the fabricated mold insert. The effects of the molding temperature and wettability property on the replication quality of the molded lenses were analyzed experimentally.