• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.5
• /
• pp.704-713
• /
• 2018

The purpose of this study is to develop a systematic framework that can scientifically and quantitatively evaluate the effectiveness of an LVC training system. The proposed framework is based on QFD(Quality Function Development) methodology. The process of developing the framework begins with identifying various needs of stakeholders related to the introduction of the LVC training system. Then the effectiveness areas and factors are derived based on the needs. The measured effectiveness for each factors on alternatives by L, V, C systems are finally synthesized into the one overall effectiveness of each training system for relative comparison among them. In addition, we developed an Excel$^{TM}$-based tool based on the proposed framework methodology to provide an ease-of-use environment for rapid evaluation on the effectiveness of each training system with the given stakeholder need importance combinations, training scenarios and assets. The suggested framework and the measurement tool are expected to be useful for efficient knowledge-based decision making on an acquisition of the LVC training system.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.4
• /
• pp.66-74
• /
• 2003

In non-contact underwater explosion shock test of a real naval ship, measurement of shock loadings and responses should require onboard system to be able to safely trigger an explosive and to simultaneously and successfully measure scores of shock signals in the deteriorated environment. For this purpose, we have developed a shock-hardened measurement system resistible to 170g peak acceleration having 4 msec duration by resiliently mounting general purpose measurement instruments in racks. The system can simultaneously measure and record 200 signals to evaluate shock leadings and responses of the test ship by triggering an explosive and measurement instruments at the same time. We prove the performance of the developed system by introducing the signal acquisition results from of a real ship underwater shock test, firstly performed in Korea.

• New & Renewable Energy
• /
• v.3 no.4
• /
• pp.114-122
• /
• 2007

This paper addresses the measurement of structural loads on the Unison U50 wind turbine. The load measurement are carried out to determine the actual loads acting on a wind turbine. This is needed not only the certification process but also improving the technical development for prototype wind turbine. The measurement system is consists of measuring load, operating quantities and meteorological signal. All data that occur during the operating of a WT are stored the data acquisition system automatically. With using the measured data, load spectrum and equivalent load are evaluated according to IEC61400-13 "Measurement of mechanical loads".

• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.250-252
• /
• 2006

In this paper, we studied for the measurement system for on-line testing and evaluation of tilting train express(TTX). The measurement system is installed in each train for the performance measurement during the test run. It is composed of software part, hardware part and can measure various signals such as velocity, voltage, temperature. The software controls the hardware of the measurement system, performs the analysis and calculation of measurement data and acts as interface between users and the system hardware. The hardware is consisted of 7 DAMs(Data Acquisition Modules) and 6 monitoring modules.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.6
• /
• pp.448-455
• /
• 2003

A system design technique of automatic thickness measurement and defect inspection system, which measures the thickness of the ALC(Autoclaved Lightweight Concrete) block and inspects the defect on a realtime basis is proposed. The image processing system was established with a CCD camera, an image grabber, and a personal computer without using assembled measurement equipment. The image obtained by this system was analyzed by a devised algorithm, specially designed for the enhanced measurement accuracy. For the realization of the proposed algorithm, the preprocessing method that can be applied to overcome uneven lighting environment, an enhanced edge decision method using 8 edge-pairs with irregular and rough surface, the unit length decision method in uneven condition with rocking objects, and the curvature calibration method of camera using a constructed grid are developed. The experimental results, show that the required measurement accuracy specification is sufficiently satisfied using our proposed method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.4
• /
• pp.328-333
• /
• 2006

In this paper, we developed a pressure measurement apparatus with the parallel structure to improve the measurement efficiency of pressure sensors by reducing the measurement time of pressure. The developed system has two parallel positions for loading Silicon pressure sensor and has a dual valve structure. The semiconductor pressure sensors prepared by Copal Electronics were used to confirm the performance of the developed measurement system. Two stage differential amplifier circuit was employed to amplify the weak output signal and the amplified output signal was improved utilizing a low-pass filter. New apparatus shows the measurement time of pressure two times shorter than that of conventional one with the serial structure, while both structures show the similar linear output versus pressure characteristics.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.6
• /
• pp.64-69
• /
• 2016

Vehicle clutch measurement for disc cushion variation was developed for the production of high quality Dual clutch transmissions. The developed device is composed of load cells for load measurement and LVDT for measuring the distance variation measurement in cushion variation. The servo motor-driven electric press for flexible loads that was developed was controlled by a PC-based HMI system, LabVIEW, and the device was able to continuously record real time measurement data with the accuracies of ${\pm}0.1\;kgf$ load and ${\pm}5{\mu}m$ cushion amount, which is far above the requirements of commercial vehicle standards.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.838-841
• /
• 2000

To improve the accuracy of products and improve the product quality, we need to enhance the machining accuracy of the machine tools. To this point of view, measurement and inspection of finished part as well as error analysis of machine tools has been studied for last several decades. OMM(On the Machine Measurement) has been issued to alternate with CMM, pointing out disadvantages of high expenses and lots of setting time in CMM. In this paper, we study 1) the spherical surface manufacturing by volumetric error compensation of machine tool, 2) the system development of OMM without detaching work piece from a bed of machine tool after working. 3) the generation of the finished part profile by On the machine measurement. Furthermore, the output of OMM is compared with that of CMM, and verified the feasibility of the measurement system.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.3
• /
• pp.292-299
• /
• 2013

The measurement in the manufacturing process of curved ship hull plates still depends on wooden templates as a standard instrument. The metrology-enabled automation in the shipbuilding process has been challenged instead of line measurement with wooden templates. The developed measurement system consists of a CCD camera, multiple structured laser sources and 3-DOF motion device. The system carries out measurement of curved profiles for large scale plates by an optical triangulation method. The results of experiment conducted in a manufacturing shop demonstrate the accurate and robust performance.

• Journal of Power System Engineering
• /
• v.10 no.2
• /
• pp.99-103
• /
• 2006

The laser interferometer has been used for measurement of the micro displacement error. Although the laser interferometer is widely accepted as a tool for measurement of motion accuracy, the set-up procedure is time-consuming because of the strict requirement on alignment between a laser head and optic units. This paper addresses the development of a laser interferometer to measure the micro displacement for a micro machine. The portable laser interferometer which integrates a laser probe and optics, is developed for the convenient measurement. For the experiment, moving mirror set up on the micro stage. The velocity decoding board is also added to calculate doppler shift frequency directly. The output signal is obtained and analyzed by LabView. Finally experiments are found out the relation between micro displacement and output signal.