• 한국전기전자재료학회논문지
• /
• 제16권6호
• /
• pp.471-476
• /
• 2003

Au/oxide/n-InP Schottky diodes were fabricated from heteroepitaxial InP layers grown on GaAs substrates by the metalorganic vapor phase epitaxy (MOVPE) method from a new combination of source materials: ethyldimethylindium (EDMIn) and tertiarybutylphosphine (TBP). Anodic oxidation technique by using a solution of 10 g of ammonium pentaborate in 100 cc of ethylene glycole as the electrolyte was used to deposit a thin oxide layer. The barrier heights determined from three different techniques, current-voltage (I-V) measurements at room temperature and in the temperature range of 273 K - 373 K, and room temperature capacitance-voltage (C-V) measurements are in good agreement, 0.7 - 0.9 eV which is considerably high as compared to the 0.45 - 0.55 eV in Au/n-InP Schottky diode without a Passivation layer. The ideality factors of 1.1 - 1.3 of the Schottky diodes were also determined from the I-Y characteristics. Deep level transient spectroscopy (DLTS) studies revealed only one shallow electron state at 92.6 meV below the bottom of the conduction band and no deep state in the heteroepitaxial InP layers grown from EDMIn and TBP.

• 한국전기전자재료학회논문지
• /
• 제31권4호
• /
• pp.261-266
• /
• 2018

When the clamp meter approaches the electric path where current is flowing, leakage current can be measured at a distance from the electric current because the induced current increases as the magnitude of the current increases and approaches nearer to the electric path. Therefore, measurements were carried out from a distance to avoid this effect. In addition, the measured values differ depending on the location of the power line that penetrates the ZCT of the clamp meter, thus measurements were performed at a location where this effect was minimized. The fraction of compliant branch circuits, whose leakage current was lower than 1.00 mA, was found to be 69.0% out of the total of 439 branch circuits, while the percentage of compliant branch circuits having an insulation resistance higher than $0.20M{\Omega}$ was found to be 93.2%. The reason why the percentage of compliant branch circuits with low leakage current was low might be due to the inclusion of capacitive leakage current in the total measured leakage current.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.435-438
• /
• 2003

The effects of oxygen partial pressure and vacuum annealing on the electrical properties of sputtered vanadium oxide($VO_x$) thin films were investigated. The thin films were prepared by r.f. magnetron sputtering from $V_2O_5$ target in a gas mixture of argon and oxygen. The oxygen/(oxygen+argon) partial pressure ratio of 0% and 8% is adopted. Electrical properties of films sputter-deposited under different oxygen gas pressures and in situ annealed in vacuum at $400^{\circ}C$ for 1h and 4h are characterized through electrical conductivity measurements. I-V characteristics were distinguished between linear and nonlinear region. In the low field region the conduction is due to Schottky emission, while at high fields it changes to Fowler-Nordheim tunneling type conduction. The conductivity measurements have shown an Arrhenius dependence of the conductivity on the temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.3-4
• /
• 2005

The Pseudo-MOSFET measurements technique has been used for the electrical characterization of the nano SOL Silicon islands for the Pseudo-MOS measurements were fabricated by selective etching of surface silicon film with dry or wet etching to examine the effects of the etching process on the device properties. The characteristics of the Pseudo-MOS was not changed greatly in the case of thick SOI film which was 205 nm. However the characteristics of the device was dependent on etching process in the case of less than 100 nm thick SOI film. The sub 100nm SOI was obtained by thinning the silicon film of standard thick SOI. The thickness of SOI film was varied from 88 nm to 44 nm by chemical etching. The etching process effects on the properties of pseudo-MOSFET characteristics, such as mobility, turn-on voltage, and drain current transient. The etching process dependency is greater in the thinner SOI and related to original SOI wafer quality.

• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1580-1586
• /
• 2021

The application of induction bending processes to industrial pipe production is increasing. The induction bending process has the effect of reducing the number of inspections and preventing leaks by reducing the weld of the pipe. For these reasons, efforts have been made to apply an induction bending process to the pipe of the PGSFR under development in Korea and this is the first attempt in the SFR design. Since the PGSFR pipe has a relatively large diameter-to-thickness ratio, it is difficult to fabricate an induction bending pipe that meets the requirements. In addition, the material properties may change because the pipe heats to a very high temperature during the induction bending process. In this study, P91 pipes were fabricated by induction bending, and the results from analyzing the induction bending process' applicability to the P91 pipe of the PGSFR are examined. The various dimensional measurements of the pipes fabricated by the induction bending process were surveyed to determine whether the requirements of the ASME Code were met. The minimum thickness, ovality, and wall buckling measured in the fabricated pipe met all the requirements. Tensile, impact, and hardness tests at various locations of the fabricated pipe also satisfied the requirements.

• Structural Engineering and Mechanics
• /
• 제81권6호
• /
• pp.737-750
• /
• 2022

Timber-Concrete Composite construction system consists of combining timber beam or deck and concrete with different connectors. Different fastener types are used in Timber-Concrete Composite systems. In this paper, the effects of two types of fasteners on structural behavior are compared. First, the notches were opened on timber beam, and combined with reinforced concrete slab by fasteners. This system is called as Notched Connection System. Then, timber beam and reinforced concrete slab were combined by new type designed fasteners in another model. This system is called as Notched-Slab Approach. Two laboratory models were constructed and bending tests were performed to examine the fasteners' effectiveness. Bending test results have shown that heavy damage to concrete slab occurs in Notched Connection System applications and the system becomes unusable. However, in Notched-Slab Approach applications, the damage concentrated on the fastener in the metal notch created in the slab, and no damage occurred in the concrete slab. In addition, non-destructive experimental measurements were conducted to determine the dynamic characteristics. To validate the experimental results, initial finite element models of both systems were constituted in ANSYS software using orthotropic material properties, and numerical dynamic characteristics were calculated. Finite element models of Timber-Concrete Composite systems are updated to minimize the differences by manual model updating procedure using some uncertain parameters such as material properties and boundary conditions.

• 대한인간공학회지
• /
• 제21권2호
• /
• pp.71-86
• /
• 2002

This study's purpose is to gain basic data for the factory automation of manufacturing custom-made girdles. For this study , obese women in their 30s and 40s was experimented through direct measuring and by the 3D scanner, by means of which the proportions of the subject's body was measured. Based upon the results of this experiment, individually designed girdles were made. In order to gain the basic data for the factory automation of manufacturing custom-made girdles, the patterns and the clothing pressure and the feeling of wearing such girdles were analyzed. This study can be summarized as follows: The material properties and the designs of existing functional girdles in the market were studied thoroughly, and the subject were required to wear those existing girdles. On the basis of this result, the experimental girdles were designed and produced which could serve well the subject's intension. The experimental girdles were of the basic long-type in order to apply to all sorts of girdles, and they were produced according to the style and pattern of the existing grading system. The second experiment was conducted by applying the subject's body measurements. Due to the elasticity of the material, in girdles the smaller measurements were to be used in this second experiment were: 80% of waist size, 84% of the hip and 85% of the thigh. To determine the length of the girdles, the same measurements were applied. The test results of the feeling of wearing the experimental girdles showed that the second, custom-made experimental girdles were better. According to the test results of the clothing pressure, the second experimental girdles(custom-made girdles) marked the higher pressure than the first on every part of the body, especially on the hips and thighs. Thus, it can be said that the second experimental girdles are better than the first in lifting up the hips. It is expected that the design methods developed in this study can be utilized as basic resources for the factory automation system of manufacturing custom-made girdles.

• 한국전기전자재료학회논문지
• /
• 제11권8호
• /
• pp.581-586
• /
• 1998

This paper describes athermally stimulated displacement current (TSDC) of arachidic acid(AA) and polyamic acid alkylamine salts(PAAS) Langmuir-Blodgett(LB) films, which is a precursor of polyimide(PI). The TSDC measurements of AA LB film were performed from temperature to about 11$0^{\circ}C$ at a rate of 0.2$^{\circ}C$/ｓ inside a vacuum chamber for a reference. And the TSDC measurements PAAS LB film were performed from room temperature to about 25$0^{\circ}C$ and temperature was increased at the same rate as that of AA LB film. They show that there are TSDC peaks at about 7$0^{\circ}C$ in the arachidic acid LB films, and at about 7$0^{\circ}C$ and 16$0^{\circ}C$ in the PAAs LB films. Results of these measurements indicate the one small peak at 7$0^{\circ}C$ is resulted from a softening of the alkyl group and the large peak at 16$0^{\circ}C$ is possibly due to dipole of C-O group in the PASS molecule. We have calculated the vertical component of the AA and PAAs L film out of the TSDC curves. It shows that the dipole moment of the AA LB film is about 70-mD at 7$0^{\circ}C$. And the dipole moment of PAAS LB film is about 040mD at 7$0^{\circ}C$ and about 200mD at 16$0^{\circ}C$ in the first measurement of TSDC. In the second measurement of TSDC of PASS LB film after cooling down to room temperature, the TSDC peaks are almost disappeared.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.172-178
• /
• 2017

열적 특성은 에너지 물질 분야에서 중요한 특성 중 하나로, 에너지 물질 분해 시 분해열을 방출하기 때문에 DSC(시차 주사 열량계, Differential Scanning Calorimetry)를 자주 사용하고 있다. 승온속도를 달리한 DSC 측정의 경우, 용융과 같은 열역학적 변화로 인해 물질의 열적 측정에 방해를 준다. 또한 kg 단위로 예측하기 때문에 mg 단위 때와는 다른 공간상의 열 변화의 변수가 생긴다. 이번 연구에서는 이 문제점을 해결하는 방안으로, 등온 조건으로 한 DSC(Differential Scanning Calorimetry) 기초 데이터로 ATKS thermokinetic 프로그램을 이용하여 열적 노화 특성을 예측한다. 그리고 g 단위로 측정하는 ARC(Accelerating Rate Calorimetry)의 데이터를 이용하여 열적 노화 특성을 예측하고 결과를 비교 할 것이다.

• 소성∙가공
• /
• 제19권6호
• /
• pp.378-386
• /
• 2010

Nowadays there has been great interest in using heat treated cast material for press dies due to several advantages like reduction in die production costs. However, in hot press forming processes H13 forged tool steel is mostly used. Cooling performance of dies in hot press forming processes is considered as an important factor of study and also the IHTC parameter between cast material die and sheet metal should be considered as an essential. In the present study, the IHTC was calculated for the sheet metal in the hot press forming process with cast and forged material dies. The temperature measurements were performed for the sheet metal, casting and forged material dies by applying various contact pressure in hot press forming. IHTC was calculated and studied by adopting the inverse heat convection method in DEFORM-2D. Each IHTC was considered as a function of contact time and contact pressure. The experimental data were compared with calculated data obtained from the proposed equation and references.