• 공업화학
• /
• 제9권7호
• /
• pp.1036-1042
• /
• 1998

소수성실관막을 이용하여 수용액 중의 Cr(VI)을 TDA로 추출하고, 이를 NaOH 수용액으로 회수하였다. 역추출공정에서의 물질전달속도는 추출공정에 비해 작았으며, 이러한 결과는 소수성막의 내부를 유기상이 흐르게 되면 추출과정에서는 무시할 수 있었던 막저항이 작용하기 때문이라 판단된다. 막수량을 달리한 4개의 막모듈(60, 100, 150, 300가닥)을 제작하였으며, 각 모듈에 대해 수용상 및 유기상의 유량이 물질전달속도에 미치는 영향에 대해서도 검토하였다. 이 실험으로부터 소수성막을 이용한 추출공정에서는, 막내부를 흐르는 수용상의 유량이 물질전달속도에 큰 영향을 주었으나 유기상 유량의 영향은 미약하다는 것을 알 수 있었다. 반면, 역추출공정에서의 물질전달속도는 수용상(회수액)유량에도 유기상(Cr-TDA 착화합물)의 유량에도 영향을 받지 않음을 알 수 있었다.

• 설비공학논문집
• /
• 제17권6호
• /
• pp.569-580
• /
• 2005

The present study investigates the convective heat/mass transfer characteristics in wavy ducts of a primary surface heat exchanger. The effects of duct aspect ratio and flow velocity on the heat/mass transfer are investigated. Local heat/mass transfer coefficients on the corrugated duct sidewall are determined using a naphthalene sublimation technique. The aspect ratios of the wavy duct are 7.3, 4.7 and 1.8 with the corrugation angle of $145\Omega$. The Reynolds numbers, based on the duct hydraulic diameter, vary from 300 to 3,000. The results show that at the low Re(Re $\leq$ 1000) the secondary vortices called Taylor-Gortler vortices perpendicular to the main flow direction are generated due to effect of duct curvature. By these secondary vortices, non-uniform heat/mass transfer coefficients distributions appear. As the aspect ratio decreases, the number of cells formed by secondary vortices are reduced and secondary vortices and comer vortices mix due to decreased aspect ratio at Re$\leq$1000. At Re >1000, the effects of corner vortices become stronger. The average Sh for the aspect ratio of 7.3 and 4.7 are almost same. But at the small aspect ratio of 1.8, the average Sh decreases due to decreased aspect ratio. More pumping power (pressure loss) is required for the larger aspect ratio due to the higher flow instability.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권1호
• /
• pp.108-116
• /
• 2003

In this paper, the experimental results of condensation heat transfer were reported for the plate and shell heat exchangers(P&SHE) using R-l34a. An experimental refrigerant loop has been established to measure the condensation heat transfer coefficient of R-l34a in a vertical P&SHE. Two vertical counter flow channels were formed in the P&SHE by three plates of geometry with a corrugated trapezoid shape of a chevron angle of 45$^{\circ}$. Downflow of the condensing R-l34a in one channel releases heat to the cold up flow of water in the other channel. The effect of the refrigerant mass flux, average heat flux, system pressure and vapor quality of R-l34a on the measured data were explored in detail. The results indicate that at a higher vapor quality the condensation heat transfer coefficients are significantly higher. Condensation heat transfer coefficients were increased when the refrigerant mass flux was increased. A rise in the average heat flux causes an slight increase in the hr. Finally, at a higher system pressure the hr is found to be lower. Correlation is also provided for the measured heat transfer coefficients in terms of the Nusselt number.

• 설비공학논문집
• /
• 제23권11호
• /
• pp.718-725
• /
• 2011

Characteristics of flow boiling heat transfer in microchannels were investigated experimentally. The microchannels consisted of 9 parallel trapezoidal channels with each channel having 205 ${\mu}m$ of bottom width, 800 ${\mu}m$ of depth, $3.6^{\circ}$ of sidewall angle, and 7 cm of length. Tests were performed with R113 over a mass velocity range of 150~920 $kg/m^2s$, heat flux of 10~100 $kW/m^2$ and inlet pressures of 105~195 kPa. Flow boiling heat transfer coefficient in microchannels was found to be dominated by heat-flux. However the effect of mass velocity was not significant. Contrary to macrochannel trends, the heat transfer coefficient was shown to decrease with increasing thermodynamic equilibrium quality. A new correlation suitable for predicting flow boiling heat transfer coefficient was developed based on the laminar single-phase heat transfer coefficient and the nucleate boiling dominant equation. Comparison with the experimental data showed good agreement.

• 설비공학논문집
• /
• 제11권2호
• /
• pp.224-235
• /
• 1999

The present study investigated the effects of the experimental parameters on the cooling characteristics of the multichip module cooled by the indirect liquid cooling method using water, PF-5060, and paraffin slurry. The experimental parameters were coolants including Paraffin slurry with mass fraction of 2.5~7.5%, heat flux of 10~40W/$\textrm{cm}^2$ for the simulated VLSI chips and Reynolds numbers of 3,000~20,000. The size of paraffin slurry was constant as 10~40${\mu}{\textrm}{m}$ before and after the experiment. The chip surface temperatures for paraffin slurry were lower than those for water and PF-5060. The local heat transfer coefficients for the paraffin slurry were larger than those for water and the local heat transfer coefficients reached a row-number-independent and thermally-fully-developed value approximately after the third row. The local Nusselt numbers for paraffin slurry with a mass fraction of 7.5% were larger by 20~38% than those for water. The paraffin slurry with a mass fraction of 5% shelved the best thermal and hydrodynamic characteristics when local heat transfer and pressure drop were considered simultaneously.

• Structural Engineering and Mechanics
• /
• 제62권1호
• /
• pp.55-64
• /
• 2017

An effective design approach for Multiple Tuned Mass Dampers (MTMDs) in pedestrian bridges was proposed by utilizing the transfer function to obtain each TMD's optimum stiffness and damping. A systematic simulation of pedestrian excitations was described. The motion equation of a typical MTMD system attached to a Multi-degree-of-freedom (MDOF) system was presented, and the transfer function from the input pedestrian excitations to the output acceleration responses was defined. By solving the minimum norm of the transfer function, the parameters of the MTMD which resulted in the minimum overall responses can be obtained. Two applications of lightly damped pedestrian bridges attached with MTMD showed that MTMDs designed through this method can significantly reduce the structural responses when subjected to pedestrian excitations, and the vibration control effects were better than the MTMD when it was considered as being composed of equal number and mass ratios of TMDs designed by classical Den Hartog method.

• 한국소음진동공학회논문집
• /
• 제25권12호
• /
• pp.822-829
• /
• 2015

A transfer matrix method has been developed to determine the more accurate natural frequencies for the bending vibration of Bernoulli-Euler beam with linearly reduced width and a concentrated tip mass. The proposed method can be computed an infinite number of the natural frequencies using a single element. Using the differential equation, shear force, and bending moment in which can be deduced by the diverse variational principles, a transfer matrix is formulated. The roots of the differential equation are computed by the Frobenius method. The effect of the concentrated mass for the natural frequencies of width-tapered beams is examined through a parametric study, and to show the accuracy of the proposed method, the computed results compared with those obtained from commercial finite element analysis program(ANSYS).

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.140-150
• /
• 2004

In this study, the effect of relative position of the blade for the fixed vane has been investigated on blade surface heat transfer. The experiments were conducted in a low speed stationary annular cascade, and heat transfer of blade was examined for six positions within a pitch. Turbine test section has one stage composed of sixteen guide vanes and blades. The chord length of the tested blade is 150 mm and the mean tip clearance of the blade having flat tip is about $2.5\%$ of the blade chord. For the detailed mass transfer measurements on the blade surfaces, a naphthalene sublimation technique was used. The inlet flow Reynolds number is fixed to $1.5{\times}10^5$. Complex heat transfer characteristics are observed on the blade surface due to various flow characteristics, such as separation bubble, relaminarization, transition to turbulence and leakage vortices. The distributions of velocity and turbulence intensity change significantly with the relative position due to the blockage effect of the blade. This causes the variation of heat transfer patterns on the blade surface. The results show that the flow near the leading edge get highly disturbed and deflected toward the either side of the blade when the blade leading edge is positioned close to the trailing edge of the vane. Therefore, separation bubble disappears on the pressure side and overall heat transfer on the relaminarization region is increased. But, due to reduced tip gap flow at the upstream region, the effect of leakage flow on the upstream region of the blade surface is weakened. Thus, the heat transfer characteristics significantly change with the blade positions.

• Structural Engineering and Mechanics
• /
• 제72권6호
• /
• pp.797-807
• /
• 2019

In this study, an exact transfer matrix expression for a twisted uniform beam considering the effect of shear deformation and rotary inertia is developed. The particular transfer matrix is derived by applying the distributed mass and transcendental function while using a local coordinate system. The results obtained from this method are independent for a number of subdivided elements, and this method can determine the required number of exact solutions for the free vibration characteristics of a twisted uniform Timoshenko beam using a single element. In addition, it can be used as a useful numerical method for the computation of high-order natural frequencies. To validate the accuracy of the proposed method, the computed results are compared with those reported in the existing literature, and the comparison results indicate notably good agreement. In addition, the method is used to investigate the effects of shear deformation and rotary inertia for a twisted beam.

• 에너지공학
• /
• 제21권1호
• /
• pp.18-25
• /
• 2012

굴뚝내 수직 원형관의 자연대류에서 굴뚝의 입구길이, 출구길이, 그리고 굴뚝의 직경에 따른 열전달 변화를 실험적으로 연구하였다. 상사성을 이용하여 열전달 실험 대신 물질전달 실험을 수행하였다. 직경 0.054 m, 높이 0.03, 0.07, 0.10 m의 원형관에 대하여 굴뚝의 직경을 0.06 m에서 0.14 m까지, 높이를 0.30 m에서 1.10 m까지 변화시켰다. 이는 Pr 수 2,094, $Ra_L$ 수 $4.55{\times}10^9$, $5.79{\times}10^{10}$, 그리고 $1.69{\times}10^{11}$에 해당한다. 굴뚝이 없을 때, 수직 원형관의 열전달은 Le Ferve의 수직평판에 대한 층류 자연대류 상관식과 일치하였다. 출구길이를 증가시키며 실험한 결과, 열전달은 증가하다가 특정 출구길이 이상에서는 일정해 졌다. 반면, 입구길이를 증가시킬 때는 열전달은 감소하다가 특정 입구길이 이상에서는 일정해졌다. 굴뚝효과로 증가된 열전달은 굴뚝의 직경을 증가시킬수록 감소하다가 굴뚝이 없을 때와 같아졌다.