• 한국표면공학회지
• /
• 제32권2호
• /
• pp.144-156
• /
• 1999

Thermal Barrier Coating with Functional Gradient Materials (FGM-TBC) can play an important role to protect the parts from harmful environments in high temperatures such as oxidation, corrosion, and wear and to improve the efficiency of aircraft engine by lowering the surface temperature on turbine blade. FGM-TBC can increase the life spans of product and improve the operating properties. Therfore, in this study the evaluations of mechanical and thermal properties of FGM-TBC such as fatigue, oxidation and wear-resistance at high temperatures have been conducted. The samples of both the TBC with 2, 3, 5 layers (YSZ/NiCrAlY) to be produced by Air Plasma Spray method (APS) and the bulk TBC with 6 layers to be produced by Plasma Assisted Sintering method (PAS) were used. Furthermore, residual stress, bond strength, and thermal conductivity were evaluated. The average thickness of the APS was 500$\mu\textrm{m}$ to 600$\mu\textrm{m}$ and the average thickness of the PAS was 3mm. The hardness number of the top layer of APS was 750 Hv to 810Hv and that of PAS was 950 Hv to 1440Hv. The $ZrO_2$ coating layer of APS was composed of tetragonal structure after spraying as the result of XRD analysis. As shown in the results of the high temperature wear test, the 3 layer coating of APS had the best wear resistance at $800^{\circ}C$ and the 5 layer coating of APS had the best wear resistance at $600^{\circ}C$. But, these coatings had the tendency of the low-temperature softening at $300^{\circ}C$. The main mechanism of wear was the adhesive wear and the friction coefficient of coatings was increased as increasing the test temperatures. A s results of thermal conductivity test, the ${\Delta}T$ of the APS coating was increased as number of layer and the range of thermal conductivity of the PAS was $800^{\circ}C$ to $1000^{\circ}C$.

• 한국분무공학회지
• /
• 제25권1호
• /
• pp.8-14
• /
• 2020

Recently, 1-D model-based engine development using virtual engine system is getting more attention than experimental-based engine development due to the advantages in time and cost. Injection rate profile is the one of the main parameters that determine the start and end of combustion. Therefore, it is essential to set up a sophisticated model to accurately predict the injection rate as starting point of virtual engine system. In this research, procedure of 1-D model setup based on AMESim is introduced to predict the dynamic behavior and injection rate of diesel injector. As a first step, detailed 3D cross-sectional drawing of the injector was achieved, which can be done with help of precision measurement system. Then an approximate AMESim model was provided based on the 3D drawing, which is composed of three part such as solenoid part, control chamber part and needle and nozzle orifice part. However, validation results in terms of total injection quantity showed some errors over the acceptable level. Therefore, experimental work including needle movement visualization, solenoid part analysis and flow characteristics of injector part was performed together to provide more accuracy of 1-D model. Finally, 1-D model with the accuracy of less than 10% of error compared with experimental result in terms of injection quantity and injection rate shape under normal temperature and single injection condition was established. Further work considering fuel temperature and multiple injection will be performed.

• 한국추진공학회지
• /
• 제7권3호
• /
• pp.1-7
• /
• 2003

본 연구에서는 열적 삭마에 의한 노즐목 면적 증가량을 알아내기 위해 KSR-III로켓의 주엔진인 KL-3 엔진의 노즐목의 형상을 측정하고자 시도하였으며, 기존에 사용하던 3차원 변위 측정기를 이용한 방식의 접근이 곤란함에 따라 영상처리 기법을 도입한 측정 방식을 고안하여 사용하였다. 영상 기반 노즐목 형상 측정 장치는 만족스런 결과를 보였다. 시험결과 분석을 통해서는 삭마의 형상은 분무 형상에 의해 결정된다는 것과, 삭마의 진행이 3개의 구간으로 나누어 설명할 수 있음을 밝혔는데, 노즐목이 원형을 그대로 유지하며 삭마진행이 미미한 구간, 원형에서 벗어나 요철형상이 발달하면서 삭마진행이 가속되는 구간, 요철형상이 이미 정착되어서 요철의 깊이만 증가하되 삭마량은 미미한 구간이다. 또한 60초 연소 후 노즐목 면적 증가율은 +5.82% 정도로 만족할 만한 수준으로 판단한다.

• 대한조선학회지
• /
• 제7권1호
• /
• pp.57-78
• /
• 1970

The Korea inshore fishing boats are the size up to 30G.T., and their construction commonly employs the traditional wide wooden planking. Nevertheless, the hull forms have been developed with chine-type straight-framed sections which give developable surface party, but not on the whole: especially not on the whole portion of the hull are preferable for them. Considering many merits in the boat construction, the author, excluding cases of the FRP construction by hand lay-up or spray-up method and of the ferro-cement construction, finds out no reasons to depart from the chine-type hull forms of a developable surface in future development of their hull forms, too. In this report, the author proposed new designs of the developable hull surface for four typical boats forming the main structure of Korean inshore fishing fleets; 5G.T.-class multi-purpose boat, 10G.T.-class angling and longlining boat, 20G.T.-class drift and gill netters, and 27G.T.-class stow netters, and presented the tank test results on their propulsion resistance. The tank test had two purposes; one is to present the powering schedule of the new designs and the other to investigate the resistance characteristics of this kinds of boat in comparision with those of equivalent round-type boats at operational speed ranges. Between the both types of the boat no material differences in powering are expected. Hence, the author is confident of that saving in the construction cost of the developable hull over that of the round-type boat may result in considerable contribution to the over-all boat economy.

• 한국분무공학회지
• /
• 제21권3호
• /
• pp.130-136
• /
• 2016

NOx and PM are important air pollutants as vehicle management policy aspect. Medium-duty truck is the main source of the pollutants although the vehicle market share is only 3.5%. National emission portion of NOx and PM form the mobile sourece are 14% and 16% respectively. In this study it was investigated that characteristics of air pollutants emission on medium duty truck equipped with EGR and SCR system. Vehicle's test reflected driving cycle on the chassis dynamometer, and applied test cycle was WHVC(World Harmonized Vehicle Cycle) mode. The test cycle include three segments, represent urban, rural and motorway driving. Based on the test results NOx, PM, HC were less emitted form SCR vehicle than EGR vehicle. And CO was less emitted form EGR vehicle than SCR vehicle due to CO oxidation reaction on DPF surface. And most air pollutants reduced as average vehicle speed increased. Pollutants were less emitted on motorway section than urban and rural sections. But highly NOx emission on motorway section was verified according to increased EGR ratio on fast vehicle speed. HC and CO additional emission was identified as 68%, 58% respectively during SCR vehicle's cold engine start emission test. NOx additional emission was detected by 24% on SCR vehicle's condition of engine cold start while not detected on vehicle equipped with EGR. SCR vehicle's additional NOx emission was derived from low reaction temperature during engine cold start condition. medium-duty truck emission characteristics were investigated in this study and expected to used to improve air pollutants management policy of medium-duty truck equipped with SCR & EGR.

• International Journal of Concrete Structures and Materials
• /
• 제11권2호
• /
• pp.199-213
• /
• 2017

Chloride penetration is among the main causes of corrosion initiation in reinforced concrete (RC) structures producing premature degradations. Weather and exposure conditions directly affect chloride ingress mechanisms and therefore the operational service life and safety of RC structures. Consequently, comprehensive chloride ingress models are useful tools to estimate corrosion initiation risks and minimize maintenance costs for RC structures placed under chloride-contaminated environments. This paper first presents a coupled thermo-hydro-chemical model for predicting chloride penetration into concrete that accounts for realistic weather conditions. This complete numerical model takes into account multiple factors affecting chloride ingress such as diffusion, convection, chloride binding, ionic interaction, and concrete aging. Since the complete model could be computationally expensive for long-term assessment, this study also proposes model simplifications in order to reduce the computational cost. Long-term chloride assessments of complete and reduced models are compared for three locations in France (Brest, Strasbourg and Nice) characterized by different weather and exposure conditions (tidal zone, de-icing salts and salt spray). The comparative study indicates that the reduced model is computationally efficient and accurate for long-term chloride ingress modeling in comparison to the complete one. Given that long-term assessment requires larger climate databases, this research also studies how climate models may affect chloride ingress assessment. The results indicate that the selection of climate models as well as the considered training periods introduce significant errors for mid- and long- term chloride ingress assessment.

• Food Science and Biotechnology
• /
• 제18권3호
• /
• pp.724-731
• /
• 2009

Anthocyanins are considered one of the main color determinants in aged red wine. The anthocyanins in aged red wine made from 'Cabernet Gernischet' (Vitis vinifera L. cv.) grape were investigated by high performance liquid chromatography- electronic spray ionization- mass spectrometry (HPLC-ESI-MS) and their color presented in aqueous solution were evaluated using partial least square regression (PLS). The results showed that there were 37 anthocyanins identified in this wine, including 22 pyranoanthocyanins. The analysis of PLS indicated that different anthocyanins showed distinct color values: malvidin 3-O-(6-O-acetyl)-glucoside-4-vinylguaiacol (Mv3-acet-glu-vg) presented the highest color values, while malvidin 3-O-glucoside (Mv3-glu) showed least. Among the free non-acylated anthocyanins, peonidin 3-O-oglucoside (Pn3-glu) showed the highest color values; the coumarylated anthocyanins presented higher color values than their corresponding acetylated anthocyanins and parent anthocyanins; pyranoanthocyanins presented also higher color values than their original anthocyanins; the color of anthocyanins depended on their structure. This work will be helpful to reveal evolution in aged red wine.

• 한국수소및신에너지학회논문집
• /
• 제21권5호
• /
• pp.375-382
• /
• 2010

A layered perovskite photocatalysts, $SrBi_2Nb_2O_9$ (SBN), was synthesized by the conventional solid-state reaction method and characterized by X-ray diffraction (XRD) and UV-visble spectrophotometry. The results showed that the structure of $SrBi_2Nb_2O_9$ is orthorhombic. Diffuse reflectance spectra for calcined and attrition-milled SBN showed the main absorption edges were less 400 nm, that is ultraviolet region. SBN under micron-sized powder was deposited on the $Al_2O_3$ by room temperature powder spray in vacuum process, so called aerosol deposition (AD), and nano-grained $SrBi_2Nb_2O_9$ photocatalytic thick film was fabricated. AD-deposited SBN thick films were characterized by XRD, scanning electron microscopy (SEM) and UV-visable spectrophotometry, Moreover, it was found that several nano-sized SBN film by AD process can improve the photocatalytic activity under visable reflectance.

• 한국항공우주학회지
• /
• 제37권2호
• /
• pp.166-174
• /
• 2009

본 연구에서는 횡단류 아음속유동장에서 연료가 여러 분사각도를 가지고 수직 분무시 나타나는 액주영역의 궤적과 분열지점에 관한 연구를 수행하였다. 직접 사진촬영 방법과 평면레이저유도형광(PLLIF) 기법으로 정방향 분사각도의 분무에서 액주영역의 궤적식과 분열지점까지의 거리에 대한 경험식을 도출하여 기존 연구결과와 비교 분석하고 대향분사의 액주 궤적식과 분열지점까지의 거리에 대한 경험식을 도출하였다. 실험을 통하여 액주영역의 궤적과 분열지점까지의 거리는 분사차압, 공기의 유속, 인젝터 지름 크기, 분사각도에 의하여 결정됨을 확인하였다.

• 한국방재학회 논문집
• /
• 제9권1호
• /
• pp.99-105
• /
• 2009

본 연구에서는 2006년 집중호우로 인해 발생한 토석류 관련 수해 및 그에 대한 복구현황에 대한 분석을 실시하였다. 이를 위해 문헌조사 및 현장답사를 통해서 2006년에 발생한 토석류의 특성, 이로 인한 수해 및 복구현황 등을 분석하였다. 2006년 강우기간 동안 최대시우량 113.5 mm, 1일 최대 강우량 355 mm의 호우가 발생하였는데 이는 80-500년의 강우빈도에 해당된다. 분석 결과에 의하면 수해의 대부분은 사면유실로부터 기인한 토석류에 의해서 발생하였다. 수해기간 동안의 강수량 자료에 대한 분석결과 강우강도와 수해 발생시점은 직접적인 관계가 있는 것으로 나타났다. 현재 수해와 관련되어 계곡부에 사방댐 및 자연 사면에 대해 사면보호공이 실시되어 있다. 본 연구에서 분석된 결과를 통하여 현행 사면수해 복구 및 관리와 관련된 문제점에 대해 대안을 제시하고자 한다.