• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.6
• /
• pp.294-302
• /
• 2023

Ni-Mn-Zn ferrite, Ni_0.5-xMn_xZn_0.5Fe₂O₄ (0 ≤ x ≤ 0.5), was synthesized using the sol-gel method to investigate the crystal structure, microstructure, magnetic properties, high-frequency characteristics, and electromagnetic (EM) wave absorption characteristics as a function of Mn substitution. As the Mn content increased, a continuous decrease in saturation magnetization (M_S) was observed with little change in coercivity (H_C). Samples for each composition (x) exhibited strong EM wave absorption performance with first and second strong EM wave absorption regions satisfying minimum reflection loss, RL_min < -40 dB in the 1.5~2.5, 6~11 GHz range, respectively. The EM wave absorption in Ni-Mn-Zn ferrite depends on magnetic loss, and adjusting µ' and µ'' spectra by Mn substitution or H field allows control of the EM wave absorption frequency.

• Journal of the Korean Ceramic Society
• /
• v.40 no.5
• /
• pp.428-433
• /
• 2003

In this study, we investigated the variation of microstructural and electromagnetic properties of YIG ferrites for Isolator/Circulator application with the sintering temperature and Zr addition. The composition of the ferrites was Y$_{2.1}$Ca$_{0.9}$Fe$_{4.4-x}$V$_{0.5}$In$_{0.05}$Al$_{0.05}$Zr$_{x}$O$_{12}$ with x=0, 0.05, 0.1 and 0.2. The YIG ferrites were prepared by the conventional ceramic sintering process. The Zr-substituted YIG ferrite, Y$_{2.1}$ Ca$_{0.9}$Fe$_{4.4-x}$V$_{0.5}$In$_{0.05}$Al$_{0.05}$ Zr$_{x}$O$_{12}$ showed the highest saturation magnetization (1097 gauss) at x=0.1. The microwave properties were shown as isolation of 18.60 dB and insertion loss of 0.45 dB at x=0.2. Additionally, Zr-substitution was effective in decreasing ferromagnetic resonance linewidth with Zr content.

• Journal of the Korean Magnetics Society
• /
• v.20 no.6
• /
• pp.228-233
• /
• 2010

The microwave permeability was measured in order to analyze the thickness dependence of loss properties in CoFeHfO thin films with varying thickness of t = 57~1368 nm. A single resonance peak (P1) at 2.95 GHz was appeared in the samples with thickness less than 405 nm, while second resonance peak (P2) at 547MHz was additionally appeared in the samples with thickness greater than 405 nm. The P2 was originated by the angle distribution of the easy axis, which was confirmed from the measured results of the change of imaginary permeability with applied magnetic field in the sample of 1368 nm thickness and low field torque curves. If the second peaks can be reduced by minimizing the angle distribution of the easy axis, the CoFeHfO thin films with thickness greater than 400 nm can be used for the compact microwave devices operated at up to 2 GHz ranges.

• Journal of the Korean Magnetics Society
• /
• v.10 no.5
• /
• pp.250-255
• /
• 2000

Double rectangular spiral thin-film inductors were fabricated using $Fe_{86.7}Zr_{3.3}B_{4}Ag_{6}$ thin film with high permeability and resistance, in which easy axis of magnetization of the thin-film was perpendicular or parallel to the current direction. The perpendicular geometry inductor revealed higher inductance than the parallel geometry one, because spin aligns of magnetic film were more easily along the field direction due to higher field intensity in the perpendicular geometry. The increase of the inductance, however, resulted in the decrease of resonance frequency. The permeability was monitored by annealing the thin-films at different temperatures. With increasing the permeability, the inductance increased, but total resistance also increased due to the increase in magnetic core loss. As the resonance frequency was higher in air-core inductor than in magnetic thin-film core inductor, it is suggested to increase the resonance frequency that the characteristic of air-core inductor rather than the magnetic properties of the thin-film should be enhanced..

• Investigative Magnetic Resonance Imaging
• /
• v.23 no.3
• /
• pp.202-209
• /
• 2019

Purpose: To investigate the temperature-based differences of cortical bone ultrashort echo time MRI (UTE-MRI) biomarkers between body and room temperatures. Investigations of ex vivo UTE-MRI techniques were performed mostly at room temperature however, it is noted that the MRI properties of cortical bone may differ in vivo due to the higher temperature which exists as a condition in the live body. Materials and Methods: Cortical bone specimens from fourteen donors ($63{\pm}21$ years old, 6 females and 8 males) were scanned on a 3T clinical scanner at body and room temperatures to perform T1, $T2^*$, inversion recovery UTE (IR-UTE) $T2^*$ measurements, and two-pool magnetization transfer (MT) modeling. Results: Single-component $T2^*$, $IR-T2^*$, short and long component $T2^*s$ from bi-component analysis, and T1 showed significantly higher values while the noted macromolecular fraction (MMF) from MT modeling showed significantly lower values at body temperature, as compared with room temperature. However, it is noted that the short component fraction (Frac1) showed higher values at body temperature. Conclusion: This study highlights the need for careful consideration of the temperature effects on MRI measurements, before extending a conclusion from ex vivo studies on cortical bone specimens to clinical in vivo studies. It is noted that the increased relaxation times at higher temperature was most likely due to an increased molecular motion. The T1 increase for the studied human bone specimens was noted as being significantly higher than the previously reported values for bovine cortical bone. The prevailing discipline notes that the increased relaxation times of the bound water likely resulted in a lower signal loss during data acquisition, which led to the incidence of a higher Frac1 at body temperature.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.4
• /
• pp.135-141
• /
• 2021

Interest is growing in the design and development of square wave driven BLDC permanent magnet motors suitable for industrial automation, and the development of position detection circuits and drivers. However, this motor is somewhat limited in its application despite the price and functional advantages due to the decrease in efficiency due to switching loss and vibration and noise. In the process of designing and assembling a BLDC motor, the magnetic pole angle is not uniform or the magnetic flux distribution is distorted due to problems in magnetic circuit design or product non-uniformity in the assembly process. Therefore, these things cause position detection deviation and deteriorate the motor characteristics. In addition, the sine wave driven BLDC system can operate stably only when the signal generated from the position sensor is accurately fed back to the driver. However, since the generated signal cannot perform stable position detection due to the occurrence of DC offset component due to magnetic flux density deviation or magnetization technology, which is an external influence, this study intends to study the proposed circuit that can remove the DC offset component.

• Korean Journal of Metals and Materials
• /
• v.46 no.3
• /
• pp.131-134
• /
• 2008

The magnetism of$Fe_3O_4$ nanoparticles was applied to magnetic bio-panning process for finding specific sequences against $Fe_3O_4$ crystal phase. Vibrating sample magnetometer (VSM) measurement showed that the coercivity of 30 Oe and the saturation magnetization of 55 emu/g were sufficient in controlling particle movement and magnetizing particles in the media, respectively. This ferrimagnetism of nanoparticles practically enhanced panning efficiency by exaggerating centrifuge step and preventing particle loss. Sequencing results showed that histidine which was commonly found in peptide sequences played an important role in the binding onto $Fe_3O_4$ nanoparticle surface. However, various possible motifs were also observed from several neighboring amino acids of histidine.

• Progress in Superconductivity
• /
• v.12 no.2
• /
• pp.118-123
• /
• 2011

The properties of $2^{nd}$ generation high temperature superconducting wire, coated conductor strongly depend on the quality of superconducting oxide layer and property of metal substrate is one of the most important factors affecting the quality of coated conductor. Good mechanical and chemical stability at high temperature are required to maintain the initial integrity during the various process steps required to deposit several layers consisting coated conductor. And substrate need to be nonmagnetic to reduce magnetization loss for ac application. Hastelloy and stainless steel are the most suitable alloys for metal substrate. One of the obstacles in using stainless steel as substrate for coated conductor is its difficulties in making smooth surface inevitable for depositing good IBAD layer. Conventional method involves several steps such as electro polishing, deposition of $Al_2O_3$ and $Y_2O_3$ before IBAD process. Chemical solution deposition method can simplify those steps into one step process having uniformity in large area. In this research, we tried to improve the surface roughness of stainless steel(SUS310). The precursor coating solution was synthesized by using yttrium complex. The viscosity of coating solution and heat treatment condition were optimized for smooth surface. A smooth amorphous $Y_2O_3$ thin film suitable for IBAD process was coated on SUS310 tape. The surface roughness was improved from 40nm to 1.8 nm by 4 coatings. The IBAD-MgO layer deposited on prepared substrate showed good in plane alignment(${\Delta}{\phi}$) of $6.2^{\circ}$.

• Journal of Powder Materials
• /
• v.28 no.4
• /
• pp.293-300
• /
• 2021

We investigate the effect of phosphorous content on the microstructure and magnetic properties of Fe_83.2Si_5.33-0.33xB_10.67-0.67xP_xCu_0.8 (x = 1-4 at.%) nanocrystalline soft magnetic alloys. The simultaneous addition of Cu and P to nanocrystalline alloys reportedly decreases the nanocrystalline size significantly, to 10-20 nm. In the P-containing nanocrystalline alloy, P atoms are distributed in an amorphous residual matrix, which suppresses grain growth, increases permeability, and decreases coercivity. In this study, nanocrystalline ribbons with a composition of Fe_83.2Si_5.33-0.33xB_10.67-0.67xP_xCu_0.8 (x = 1-4 at.%) are fabricated by rapid quenching melt-spinning and thermal annealing. It is demonstrated that the addition of a small amount of P to the alloy improves the glass-forming ability and increases the resistance to undesirable Fe_x(B,P) crystallization. Among the alloys investigated in this work, an Fe_83.2Si₅B₁₀P₁Cu_0.8 nanocrystalline ribbon annealed at 460℃ exhibits excellent soft-magnetic properties including low coercivity, low core loss, and high saturation magnetization. The uniform nanocrystallization of the Fe_83.2Si₅B₁₀P₁Cu_0.8 alloy is confirmed by high-resolution transmission electron microscopy analysis.