• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.2A
• /
• pp.152-161
• /
• 2007

IEEE 802.11 Wireless Local Area Network (WLAN) became a prevailing technology for the broadband wireless Internet access, and new applications such as Voice over WLAM (VoWLAN) are fast emerging today. For the battery-powered VoWLAN devices, the standby time extension is a key concern for the market acceptance while today's 802.11 is not optimized for such an operation. In this paper, we propose a novel Idle Mode operation, which comprises paging, idle handoff, and delayed handoff. Under the idle mode operation, a Mobile Host (MH) does not need to perform a handoff within a predefined Paging Area (PA). Only when the MH enters a new PA, an idle handoff is performed with a minimum level of signaling. Due to the absence of such an idle mode operation, both IP paging and Power Saving Mode (PSM) have been considered the alternatives so far even though they are not efficient approaches. We implement our proposed scheme in order to prove the feasibility. The implemented prototype demonstrates that the proposed scheme outperforms the legacy alternatives with respect to energy consumption, thus extending the standby time.

• Transactions of the Korean hydrogen and new energy society
• /
• v.12 no.1
• /
• pp.29-38
• /
• 2001

The alloys $ZrMn_2Ni_x$ (x=0.0, 0.3, 0.6, 0.9 and 1.2) as the alloys of Zr-Mn-Ni three component system were prepared and their hydrogen-storage properties and their electrochemical properties were investigated. The C14 Laves phase formed in all the alloys $ZrMn_2Ni_x$. Among these alloys $ZrMn_2Ni_{0.6}$ was activated relatively easily(after about 11 charge-discharge cycles), and had the largest discharge capacity(max. 45mAh/g). For all the alloys Zr was dissolved most easily into the 6M KOH solution. More Mn and Ni were dissolved from the $ZrMn_2Ni_{0.6}$ alloy than from the other alloys. Due to the active charge and discharge of the $ZrMn_2Ni_{0.6}$ alloys, related to the easier activation and the larger discharge capacity, Zr, Mn and Ni in this alloy were considered to be dissolved more easily into the 6M KOH solution, compared with the other alloys.

• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.4
• /
• pp.161-167
• /
• 1998

It has been investigated the effects of alloying elements and binders on the corrosion behavior of metal hydride electrodes for anode of Ni/MH secondary battery. The $AB_5$-type alloys, $(LM)Ni_{4.49}Co_{0.1}Mn_{0.205}Al_{0.205}$ and $(LM)Ni_{3.6}Co_{0.7}Mn_{0.3}Al_{0.4}$, were used for the experiments. The electrodes were prepared by mixing and cold-pressing of alloy powders with Si sealent or PTFE powders, or cold-pressing the electroless copper coated alloy powders. The amount of copper coating was 20wt%. In order to examine corrosion behavior of the electrodes, the corrosion current and the current density, in 6M KOH aqueous solution after removal of oxygen in the solution, were measured by potentiodynamic and cyclic voltamo methods. The results showed that Co in the alloy increased corrosion resistance of the electrode whereas Ni decreased the stability of the electrode during the charge-discharge cycles. The electrode used Si sealant as a binder showed a lower corrosion current density than the electrode used PTFE and the electrode used Cu-coated alloy powders showed the best corrosion resistance.

• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.4
• /
• pp.135-141
• /
• 1998

The effects of heat-treatment on discharge characteristics of $TiFe_{1-x}Ni_x$ alloy were investigated. The content of Ni in alloy was varied from x = 0.1 to 0.6 by each 0.1 increment. Discharge capacity change of each alloy with C/D cycles was measured. With increasing Ni-content initial discharge capacity was increased. but at x = 0.6 it was deceased again. With increasing C/D cycles discharge capacity was rapidly decreased in the alloy of high Ni-content. In order to investigate the effects of heat-treatment on cycle life, $TiFe_{0.5}Ni_{0.5}$ alloy having maximum initial discharge capacity was heat-treated at various temperatures in the range of $700{\sim}900^{\circ}C$ and tested. The loss of initial discharge capacity was appeared at all temperatures. but cycle characteristics of the alloy was improved. The electrodes heat-treated for 1 hour in the range of $700{\sim}850^{\circ}C$ showed good recovery of discharge capacities through repeated cycles, and from SEM observation results these were considered as 1 hour in the range of $700{\sim}850^{\circ}C$ showed good recovery of discharge capacities through repeated cycles, and from SEM observation results these were considered asbeing due to increased electrode strength and small loss of porosity during heat-treatment. The electrode heat-treated for 1 hour at $900^{\circ}C$ showed poor discharge characteristics because of low porosity.

• Journal of KIISE:Databases
• /
• v.32 no.1
• /
• pp.56-70
• /
• 2005

The results of location-dependent queries(LDQ) generally depend on the current locations of query issuers. Many mechanisms, e.g. broadcast scheme, hoarding, or racking policy, have been developed to improve the system peformance and provide better services, which are specialized for LDQs. Considering geographical adjacency of data and characteristics oi target area, caching policy and broadcast scheme affect the overall performance in LDQ. For this reason, we propose both the caching policy and broadcast scheme, which these features are reflected in. Based on the adjacency of data in LDQ, our broadcast scheme use Hilbert curve to cluster data. Moreover, in order to develop the caching policy suitable for LDQ on urban area, we apply the moving distance of a MH(Mobile Host) to our caching policy We evaluate the performance of the caching policy measuring the workload of MHs and the correctness of LDQ results and the performance of the broadcast scheme measuring the average setup-time of MHs in our experiments. Finally, we expect that our caching policy Provides more correct answers when executing LDQ in focal cache and leads significant improvement of the performance of MHs. It also seems quite probable that our broadcast scheme leads improvement of battery life of the MH.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.2
• /
• pp.156-165
• /
• 2017

This study quantitatively assessed the environmental impacts of fuel cell (FC) systems by performing life cycle assessment (LCA) and analyzed their energy efficiencies based on energy return on investment (EROI) and electrical energy stored on investment (ESOI). Molten carbonate fuel cell (MCFC) system and polymer electrolyte membrane fuel cell (PEMFC) system were selected as the fuel cell systems. Five different paths to produce hydrogen ($H_2$) as fuel such as natural gas steam reforming (NGSR), centralized naptha SR (NSR(C)), NSR station (NSR(S)), liquified petroleum gas SR (LPGSR), water electrolysis (WE) were each applied to the FCs. The environmental impacts and the energy efficiencies of the FCs were compared with rechargeable batteries such as $LiFePO_4$ (LFP) and Nickel-metal hydride (Ni-MH). The LCA results show that MCFC_NSR(C) and PEMFC_NSR(C) have the lowest global warming potential (GWP) with 6.23E-02 kg $CO_2$ eq./MJ electricity and 6.84E-02 kg $CO_2$ eq./MJ electricity, respectively. For the impact category of abiotic resource depletion potential (ADP), MCFC_NGSR(S) and PEMFC_NGSR(S) show the lowest impacts of 7.42E-01 g Sb eq./MJ electricity and 7.19E-01 g Sb eq./MJ electricity, respectively. And, the energy efficiencies of the FCs are higher than those of the rechargeable batteries except for the case of hydrogen produced by WE.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.2
• /
• pp.106-111
• /
• 1999

The effect of the MG on the electrochemical charge-discharge properties of $CaNi_5$ hydrogen storage alloys was investigated under Ar and $H_2$ atmosphere. $CaNi_5$ alloy was partially decomposed to CaO and Ni phase during the MG process. The decomposition of $CaNi_5$ alloy was enhanced by the MG process which leads to crash and reformation of oxide layer on the alloy surface. As the MG process time increased, initial discharge capacity of the electrode was reduced, but the decay rate of the capacity compared to $CaNi_5$ alloys was slower. It may be described that the degradation of $MG-CaNi_5$ electrode was caused by the reduction of the reversible hydrogen reaction sites and increasing polarization resistance of hydrogen adsorption resulted from phase decomposition and disorder during the MG process, and/or by hydroxide formation during the electrochemical charge-discharge cycles.

• Transactions of the Korean hydrogen and new energy society
• /
• v.12 no.1
• /
• pp.39-50
• /
• 2001

Vanadium based solid solution alloys have been studied as a potential negative electrode of Ni/MH battery due to their high hydrogen storage capacity. In order to improve the kinetic property of V-Ti alloy in KOH electrolyte, the ball-milling process with Ni, which has a catalytic effect of hydrogen absorption/desorption, was carried out to modify the surface properties of V-Ti-Cr alloys with high hydrogen storage capacity. Moreover, to overcome the problem of poor cycle life, V-Ti alloy substituted by Cr, V0.68 Ti0.20 Cr0.12, has been developed showing a good cycle performance (keeping about 80 % of initial discharge capacity after 200 cycles). The cycle life of surface-modified V0.68 Ti0.20 Cr0.12 alloy was improved by suppressing the formation of TiO2 layer on the alloy surface while decreasing the amount of dissolved vanadium in the KOH electrolyte. In order to promote the effect of Ni coating on the surface property of V0.68 Ti 0.20 Cr 0.12 alloy by ball-milling, filamentary-typed Ni, which has higher surface coverage area than sphere-typed Ni was used as a surface modifier. Consequently, the surface-modified V0.68 Ti0.20 Cr0.12 alloy electrode showed a improved discharge capacity of 460 mAh/g.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.1
• /
• pp.52-59
• /
• 2007

We investigated the effects of the addition of Mn and $AB_5$ type alloy on the electrochemical characteristics of Ti-Cr-V BCC type alloys as anode materials for Ni-MH battery. The activation behavior and discharge capacity of the BCC type alloys were significantly improved by ball-milling with the $LmNi_{4.1}Al_{0.25}Mn_{0.3}Co_{0.65}$ alloy, because the $AB_5$ type alloy acted as hydrogen path on the surface of the BCC type alloy. Among the Mn substituted alloys($Mn=0.03%{\sim}0.08%$), the $Ti_{0.32}Cr_{0.38}Mn_{0.05}V_{0.25}$ alloy ball-milled with $AB_5$ type alloy exhibited the greatest discharge capacity of $336\;mAh{\cdot}g^{-1}$. In addition, Mn substituted alloys exhibited the lower plateau pressure in P-C- T curve, the better hydrogen storage capacity and faster surface activation compared with the alloy without Mn.

• Transactions of the Korean hydrogen and new energy society
• /
• v.10 no.2
• /
• pp.141-149
• /
• 1999

Recently the Ni/MH secondary battery has been studied extensively to achieve higher energy density, longer cycle life and faster charging-discharging rate etc. In this work, the electrode properties of $(LM)Ni_{4.49}Co_{0.1}Mn_{0.205}Al_{0.205}$ alloy and $Ti_{0.6}Zr_{0.4}V_{0.6}Ni_{1.4}$ alloy with addition of Pd were investigated. These alloys did not show any change in XRD pattern by Pd addition. As Pd was added as alloy element, the activation behavior was not affected significantly in both $AB_2$ type and $AB_5$ type electrodes and, On charging and discharging in high current density, Discharge capacity with increasing of Pd content was more decreased. But cycle life was showed increasing. Especially the electrode of $Ti_{0.6}Zr_{0.4}V_{0.6}Ni_{1.4}+0.5wt%$ Pd alloy was not almost decreased discharge capacity for 400cycles.