• 한국정밀공학회지
• /
• 제26권5호
• /
• pp.48-56
• /
• 2009

In this paper, laser-assisted machining(LAM) has been employed to machine hot isostatically pressed (HIPed) Si3N4 work pieces. Due to little residual flaws and porosity, HIPed $Si_3N_4$ work pieces are more difficult to machine compared to normally sintered $Si_3N_4$ workpieces. In LAM, the intense energy of laser was used to enhance machinability by locally heating the workpiece and thus reducing yield strength. In experiments, the laser power ranges from 200W to 800W and the diameter of work pieces is 16mm. While machining, the surface temperature was kept nearly constant by laser heating except for a short period of rise time of max. 58 seconds. Results showed as feed rate increases the surface temperature of $Si_3N_4$ workpieces decreases slightly, whereas the effect of depth of cut is disregardable. With a laser power of 800W, achievable maximal depth of cut as 0.7mm and feed rate was 0.03mm/rev.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권2호
• /
• pp.312-317
• /
• 2015

In this paper, the RF characteristics of multi-finger MOSFETs were improved by decreasing the parasitic capacitance in spite of increased gate resistance in a 90-nm CMOS technology. Two types of device structures were designed to compare the parasitic capacitance in the gate-to-source ($C_{gs}$) and gate-to-drain ($C_{gd}$) configurations. The radio frequency (RF) performance of multi-finger MOSFETs, such as cut-off frequency ($f_T$) and maximum-oscillation frequency ($f_{max}$) improved by approximately 10% by reducing the parasitic capacitance about 8.2% while maintaining the DC performance.

• 한국기계가공학회지
• /
• 제8권3호
• /
• pp.27-32
• /
• 2009

In this study, static and dynamic stability estimations on the diecutter with finite element modelling were carried out to be creased and cut away printed sheet exactly. To cut away the sheet exactly, the large force should be pressured on diecutter. And which affects not only the quality of produced sheets but also the stability of diecutter. The analyses with and without the tare of diecutter were carried out with NASTRAN software on applying 400 ton force to its top and moving table respectively. It was known that maximum von-Mises stress of 221 Mpa in diecutter was occurred at the toggle, and it was smaller than the yield stress of 280 Mpa. And maximum deformation of 0.75 mm was occurred at the top table. The natural frequencies of 41, 102, 108, 115, and 134 Hz for the 1st, 2nd, 3rd, 4th and 5th mode, which had been determined by numerical simulation, were not coincided with the max. speeds of motor and moving table of 29 and 2 Hz. And which was verified by vibration test. Therefore it may be estimated that the structure of the diecutter is statically and dynamically stable.

• 대한전자공학회논문지SP
• /
• 제45권3호
• /
• pp.30-36
• /
• 2008

멀티미디어 정보는 다매체, 다특징, 다표현, 대용량성의 특징과 함께 그 양 또한 급속도로 증가하고 있다. 따라서 급격히 늘어난 방대한 정보로부터 필요한 정보를 검색하는 검색 시스템이 요구되고 있으며, 이러한 색인 및 검색 시스템이 실시간으로 처리되는 것이 필요하다. 동영상의 내용 기반 검색을 위하여 가장 일반적으로 사용할 수 있는 정보는 영상정보이다. 영상정보는 주로 비디오를 장면 분할할 때에 사용되며 이를 통하여 구조적인 비디오 브라우징을 할 수 있다. 비디오를 샷으로 구분하는 작업을 비디오 분할(video segmentation)이라고 하며, 비디오 분할을 위해 장면의 전환점인 컷을 검출하는 작업을 컷 검출(cut detection)이라고 한다. 본 연구에서는 MPEG-7 시각 기술자인 HMMD 컬러 모델과 에지 히스토그램 기술자를 사용하여 동영상 분할을 하였다. HMMD 컬러 공간은 다른 공간에 비해 인간의 색 지각에 매우 밀접한 것으로 나타난다. 본 논문에서는 이러한 검색 시스템을 하드웨어로 구현하였다.

• Geomechanics and Engineering
• /
• 제30권1호
• /
• pp.67-73
• /
• 2022

In this study, the fiber orientation distribution (FOD) is investigated using both micro-CT (computerized tomography) and image analysis of physically cut specimens prepared from Polyvinyl Alcohol (PVA) fiber reinforced cemented Toyoura sand. The micro-CT images of the fiber reinforced cemented sand specimens were visualized in horizontal and vertical sections. Scans were obtained using a frame rate of two frames and an exposure time of 500 milliseconds. The number of images was set to optimize and typically resulted in approximately 3000 images. Then, the angles of the fibers for horizontal sections and in vertical section were calculated using the VGStudio MAX software. The number of fibers intersecting horizontal and vertical sections are counted using these images. A similar approach was used for physically cut specimens. The variation of results of fiber orientation between micro-CT scans and visual count were approximately 4-8%. The micro-CT scans were able to precisely investigate the fiber orientation distribution of fibers in these samples. The results show that 85-90% of the PVA fibers are oriented between ±30° of horizontal, and approximately 95% of fibers have an orientation that lies within ±45° of the horizontal plane. Finally, a comparison of experimental results with the generalized fiber orientation distribution function 𝜌(θ) is presented for isotropic and anisotropic distribution in fiber reinforced cemented Toyoura sand specimens. Experimentally, it can be seen that the average ratio of the number of fibers intersecting the finite area on a vertical plane to number of fibers intersecting the finite area on a horizontal plane (N^V_tot/N^H_tot) cut through a sample varies from 2.08 to 2.12 (an average ratio of 2.10 is obtained in this study). Based up on the analytical predictions, it can be seen that the average N^V_tot/N^H_tot ratio varies from 2.13 to 2.17 for varying n values (an average ratio of 2.15).

• 한국언어정보학회:학술대회논문집
• /
• 한국언어정보학회 2007년도 정기학술대회
• /
• pp.430-439
• /
• 2007

In this paper, we use non-negative matrix factorization (NMF) to refine the document clustering results. NMF is a dimensional reduction method and effective for document clustering, because a term-document matrix is high-dimensional and sparse. The initial matrix of the NMF algorithm is regarded as a clustering result, therefore we can use NMF as a refinement method. First we perform min-max cut (Mcut), which is a powerful spectral clustering method, and then refine the result via NMF. Finally we should obtain an accurate clustering result. However, NMF often fails to improve the given clustering result. To overcome this problem, we use the Mcut object function to stop the iteration of NMF.

• 마이크로전자및패키징학회지
• /
• 제9권1호
• /
• pp.1-7
• /
• 2002

본 연구에서는 이동통신 시스템의 키부품으로 필수적인 멀티미디어용 고주파 Active Filter 및 초소형 설계기술(SMD타입)을 개발하였으며, 멀티미디어 고주파 능동필터의 카오프 주파수는 2.5 mHz, 이득은100 kHz에서 0.5d B, 통과대역 리플은 100 kHz에서 2 MHz까지 최고1.2dB, GDT는 100 kHz에서 2.0 MHz까지 최고 60 nsec이며, 감쇄는 3.7 MHz에서 최소 40dB임.

• Journal of Information Display
• /
• 제12권2호
• /
• pp.109-113
• /
• 2011

This paper summarizes the recent fabrication and characterizations of flexible high-speed radio frequency (RF) transistors, PIN-diode single-pole single-throw switches, as well as flexible inductors and capacitors, based on single-crystalline Si nanomembranes transferred on polyethylene terephthalate substrates. Flexible thin-film transistors (TFTs) on plastic substrates have reached RF operation speed with a record cut-off/maximum oscillation frequency ($f_T/f_{max}$) values of 3.8/12 GHz. PIN diode switches exhibit excellent ON/OFF behaviors at high RF frequencies. Flexible inductors and capacitors compatible with high-speed TFT fabrication show resonance frequencies ($f_{res}$) up to 9.1 and 13.5 GHz, respectively. Robust mechanical characteristics were also demonstrated with these high-frequency passives components.

• 충청수학회지
• /
• 제34권2호
• /
• pp.181-188
• /
• 2021

Let X be a nondegenerate reduced closed subscheme in ℙⁿ. Assume that π_q : X → Y = π_q(X) ⊂ ℙ^n-1 is a generic projection from the center q ∈ Sec(X) \ X where Sec(X) = ℙⁿ. Let Z be the singular locus of the projection π_q(X) ⊂ ℙ^n-1. Suppose that I_X has the almost minimal presentation, which is of the form R(-3)^β_2,1 ⊕ R(-4) → R(-2)^β_1,1 → I_X → 0. In this paper, we prove the followings: (a) Z is either a linear space or a quadric hypersurface in a linear subspace; (b) $H^1({\mathcal{I}_X(k)})=H^1({\mathcal{I}_Y(k)})$ for all k ∈ ℤ; (c) reg(Y) ≤ max{reg(X), 4}; (d) Y is cut out by at most quartic hypersurfaces.

• 한국정보기술학회 영문논문지
• /
• 제9권1호
• /
• pp.89-102
• /
• 2019

Collagen can be used in building artificial skin replacements for treatment of burns and towards the reconstruction of bone as well as researching cell behavior and cellular interaction. The strength of collagen in connective tissue rests on the characteristics of collagen fibers. 3D confocal imaging of collagen fibers enables the characterization of their spatial distribution as related to their function. However, the image stacks acquired with confocal laser-scanning microscope does not clearly show the collagen architecture in 3D. Therefore, we developed a new method to reconstruct, visualize and characterize collagen fibers from fluorescence confocal images. First, we exploit the tensor voting framework to extract sparse reliable information about collagen structure in a 3D image and therefore denoise and filter the acquired image stack. We then propose to segment the collagen fibers by defining an energy term based on the Hessian matrix. This energy term is minimized by a min cut-max flow algorithm that allows adaptive regularization. We demonstrate the efficacy of our methods by visualizing reconstructed collagen from specific 3D image stack.