• Journal of Advanced Marine Engineering and Technology
• /
• v.8 no.2
• /
• pp.39-50
• /
• 1984

The plane bending corrosion fatigue test was performed on the welded zone between SM58 steel plate and SM41 steel plate jointed with submerged arc welding in the air and in the natural sea water with various conditions. The main results obtained from the test are summarized as follows: 1) The welded zone of the steel plates has the lowest impact strength and the highest electrode potential, but the hardness was mediate of SM58 base and SM41 base. 2) The cathodic protection of the welded zone was also effective for the plane bending corrosion fatigue, and the optimum protection potential of the welded zone was -1,000 mV SCE. 3) The corrosion fatigue strength under the various stress conditions of the steel plate could be estimated and also the require safety factors on the design could be obtained from the plane bending fatigue limit diagram.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1453-1458
• /
• 2011

This paper dealt with the measurement and analysis of electromagnetic waves generated by partial discharges in insulation oil to develop insulation diagnostic techniques for power transformer. Two types of narrow-band monopole antennas with the resonant frequency of 500 MHz and 1 GHz were designed and fabricated. We simulated defects which consist of a needle electrode with curvature radius of 10 ${\mu}m$ and a plane electrode with diameter of 60 mm in insulation oil. From the experiment, the maximum output voltage of the fabricated antennas was measured; 620 $mV_{max}$ for 500 MHz resonant frequency and 920 $mV_{max}$ for 1 GHz resonant frequency.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.319-324
• /
• 2011

This paper dealt with a partial discharge (PD) detection method for insulation diagnosis in cast-resin transformers. To detect PD pulse, a planar-capacitive probe was designed and fabricated. The probe has no insulation problem and can be installed on cast-resin transformers even in operation since it does not connect with high voltage conductor. The PD measurement system consists of the capacitive probe, a coupling network of 100 [kHz] low-cutoff frequency, and an amplifier with a gain of 40 [dB] and a frequency bandwidth of 500 [Hz]~45 [MHz]. A plane-needle and a plane-plane electrode system were fabricated to simulate insulation defects in a cast-resin transformer. Sensitivity of the PD measurement system, which is evaluated by a standard calibrator was 0.35 [mV/pC] for positive and 0.45 [mV/pC] for negative, respectively. The PD detection by the capacitive probe was less sensitive than that by a coupling capacitor according to IEC 60270, but we could analyze the magnitude and the phase distribution of PD pulse.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.44 no.4
• /
• pp.413-422
• /
• 2011

An improved split-beam transducer for a 50 kHz fish-sizing echo sounder was developed. The main objective of this study was to minimize the side lobe level in the beam pattern and the distance between acoustic centers for adjacent transducer quadrants in the geometrical arrangement of array elements while maintaining a given number of transducer elements and beam width. To achieve these goals, a 32-element planar array transducer ($6{\times}6$ array with one element in each corner missing) was designed using the Dolph-Chebyshev shading function to suppress side lobes in the array beam pattern and fabricated by arranging the inter-element spacing to be substantially equal to half the wavelength using the transducer element of 0.4 times the wavelength in diameter. The performance characteristics of this split-beam transducer were evaluated in the experimental water tank of $5m{\times}5m{\times}6m$ (length${\times}$height${\times}$width). In this study, the design goal of the beam width and side lobe level for transmitting a beam pattern was initially set at $21^{\circ}$ and -30 dB, respectively. However, the measured beam width at 3 dB was $21^{\circ}$ in both directions with side lobe levels of -24.7 dB in the horizontal plane and -25.6 dB in the vertical plane. The averaged beam width at -3 dB of the receiving beam patterns for four receiving quadrants was $31.4^{\circ}$. The transmitting voltage response was 161.5 dB (re $1{\mu}Pa$/V at 1 m) at 50.23 kHz with a bandwidth of 2.16 kHz, and the averaged receiving sensitivity for four receiving quadrants was -178.13 dB (re 1 V/${\mu}Pa$) at 49.8 kHz with a bandwidth of 2.64 kHz.

• Journal of Magnetics
• /
• v.11 no.2
• /
• pp.87-89
• /
• 2006

CoFeV thin film alloys were fabricated by electrodeposition, and the dependences of their magnetic properties on the current density were investigated using an X-ray diffractometer and a vibrating sample magnetometer. The deposited Co increased from about 45 to 60 wt.% with increasing current density until $25mA/cm^2$ whereas the deposited Fe decreased from about 55 to 40 wt.% with increasing current density until $25mA/cm^2$. The deposited V, about 2 wt.%, was independent of the current density. The current efficiencies of electrodeposition decreased linearly from about 40 to 29% with increasing current density. The X-ray diffraction measurement showed that all peaks of the CoFeV films were consistent with those of a typical Co hcp and Fe bcc mixed phase. An increase in the current density decreased the grain size and increased the lattice constant. The saturation magnetization increased from about 2.2 to 2.5 T with increasing current density. The coercivity measured in the perpendicular direction decreased from 260 to 120 Oe with increasing current density; a drastic drop of 60 Oe occurred at $5mA/cm^2$. The coercivity measured in the in-plane direction remained almost unchanged, at about 20 Oe, with increasing current density.

• Journal of the Korean Mathematical Society
• /
• v.56 no.2
• /
• pp.523-537
• /
• 2019

We estimate the essential norms of Volterra-type integral operators $V_g$ and $I_g$, and multiplication operators $M_g$ with holomorphic symbols g on a large class of generalized Fock spaces on the complex plane ${\mathbb{C}}$. The weights defining these spaces are radial and subjected to a mild smoothness conditions. In addition, we assume that the weights decay faster than the classical Gaussian weight. Our main result estimates the essential norms of $V_g$ in terms of an asymptotic upper bound of a quantity involving the inducing symbol g and the weight function, while the essential norms of $M_g$ and $I_g$ are shown to be comparable to their operator norms. As a means to prove our main results, we first characterized the compact composition operators acting on the spaces which is interest of its own.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.20 no.2
• /
• pp.114-118
• /
• 1987

The authors carried out a model experiment to examine the hydrodynamic charactristics of the simple camber and the super-V otter board. The model otter boards are made of 1 mm thick iron plate. The simple camber otter board is made to have $12\%$ camber ratio and $432\;cm^2$ plane projected area, and the super-V otter board to have the same camber ratio as the former in every latitudinal section and almost the same plane projected area. The experiment had been done in a circular flow tank in the speed range of $0.1\~1.2m/sec$. As a result, it is examined that in the simple camber otter board the most effective angle of attack is about $25^{\circ}$, the shearing coefficient 1.47 and the drag coefficient 0.42, while in the super-V otter board they are about $20^{\circ}$, 1.40 and 0.40 respectively, so that the simple camber otter board performs a little better efficiency than the super-V otter board.

• Korean Journal of Optics and Photonics
• /
• v.8 no.1
• /
• pp.47-51
• /
• 1997

A Cr:LiSAF laser pumped by semiconductor lasers was constructed. The pumping laser was a high-power semiconductor laser (SDL 7432-H1) of wavelength 674 nm and maximum power of 500 mW. The laser crystal was a Cr:LiSAF of plano-Brewster shape with 3% Cr3+ion concentration and 3 mm in length. The plane facet of the crystal was coated to get the maximum transmittance of pupmping laser and maximu reflection over the 800 - 880 nm bandwidth. V-shaped resonator was used to compensate the astigmatism induced by the crystal. The output power of the Cr:LiSAF laser was 19.4 mW at the pumping power of 290 mW. The wavelength was tuned by a steep dive-angled birefringent filter from 840 nm to 880 nm and the characteristics of the filter were agreed well with a theory.

• Geomechanics and Engineering
• /
• v.35 no.4
• /
• pp.385-393
• /
• 2023

To analyze the consolidation with horizontal sand drains, the plane strain consolidation model under multi-ramp loading is established, and its corresponding analytical solution is derived by using the separation of variables method. The proposed solution is verified by the field measurement data and finite element results. Then, the effects of the loading mode and stress distribution on consolidation and dissipation of pore pressure are investigated. At the same time, the influence of hydraulic conductivity and thickness of sand blankets on soil consolidation are also analyzed. The results show that the loading mode has a significant effect on both the soil consolidation rate and generation-dissipation process of pore water pressure. In contrast, the influence of stress distribution on pore pressure dissipation is obvious, while its influence on soil consolidation rate is negligible. To guarantee the fully drained condition of the sand blanket, the ratio of hydraulic conductivity of the sand blanket to that of clay layer k_d/k_v should range from 1.0×10⁴ to 1.0×10⁶ with soil width varying from 100 m to 1000 m. A larger soil width correspondingly needs a greater value of kd/kv to make sure that the pore water can flow through the sand blanket smoothly with little resistance. When the soil width is relatively small (e.g., less than 100 m), the effect of thickness of the sand blanket on soil consolidation is insignificant. And its influence appears obvious gradually with the increase of the soil width.

• Current Photovoltaic Research
• /
• v.8 no.1
• /
• pp.33-38
• /
• 2020

Single-phased SnS thin films have been prepared by RF magnetron sputtering at various deposition pressures. The effect of deposition pressure on the structural and optical properties of polycrystalline SnS thin films was studied using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible-near infrared (UV-Vis-NIR) spectrophotometer. The XRD analysis revealed the orthorhombic structure of the SnS thin films oriented along the (111) plane direction. As the deposition pressure was increased from 5 mTorr to 15 mTorr, the intensity of the peak on the (111) plane increased, and the intensity decreased under the condition of 20 mTorr. The binding energy difference at the Sn 3d_5/2 and S 2p_3/2 core levels was about 324.5 eV, indicating that the SnS thin film was prepared as a pure Sn-S phase. The optical properties of the SnS thin films indicate the presence of direct allowed transitions with corresponding energy band gap in the rang 1.47-1.57 eV.