• Journal of electromagnetic engineering and science
• /
• v.5 no.2
• /
• pp.97-103
• /
• 2005

This paper describes the measured results of sonobuoy transmitting antenna system for anti-submarine warfare (ASW). Since radiation pattern and power density depend on impedance matching between transmitting RF part and antenna with termination resistance, design of matching circuit is very important for sonobuoy system performance. Matching circuit is designed by Smith chart using control of L and C. In standing wave ratio(SWR) measurement using Network Analyzer, SWR of antenna with matching circuit observed 1.5 below at the assigned VHF band. It shows very excellent performance comparison with conversional product that is used for the same object. The measured vertical and horizontal radiation patterns are also shown the satisfaction of military specifications. A drop out of sonobuoy system on the sea is happened when angle of elevation direction is over 10 degrees, and it is conformed that it takes less than I second return to original signal level. The required electric power density is $83\;mW/m^2$ in the military specification, and measured electric power density is observed over average $110\;mW/m^2$ at all frequency bands.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.335-339
• /
• 2003

This Paper describes the design and the simulation results of the RF CMOS Class-E Power Amplifier for a 2.4GHz ISM band. This circuit is composed two connected amplifiers. where Class F amplifier drives Class E amplifier. The proposed circuit can reduce the total power dissipation of the driving stage and can work with higher efficiency. The power amplifier has been implemented in a standard 0.25$\mu\textrm{m}$ CMOS technology and is shown to deliver 100mW output Power to load with 41％ power added efficiency(PAE) from a 2.5V supply.

• Journal of Convergence Society for SMB
• /
• v.6 no.4
• /
• pp.25-30
• /
• 2016

This paper presents on the development of a compact anti-lost device requested recently. The proposed device consists of the master and slave modules based on Bluetooth4.1 technology. To implement a low-power characteristic, an algorithm has been also developed. The transmitting and receiving circuits are designed by using BoT CLE110 module supporting Bluetooth 4.1. The ATmega 328P-AU was used for the control and LP3874EMP was used as a linear regulator. Power consumption of the fabricated product in operating mode is only 10mAh and 35mAh for MCU operating state. Alarm operation distance is $10m{\pm}30%$, the effective radiated power is less than 10mW, the frequency band is designed to operate in the Bluetooth band with 26MHz bandwidth. And algorithms have been developed to extend the battery life. The size of the product was obtained as $45{\times}45{\times}15mm$ for master and $35{\times}35{\times}10mm$ fr slave. After the optimization process, it is expected to be commercialized as a wristwatch for anti-lost device.

• Journal of Korea Society of Industrial Information Systems
• /
• v.20 no.4
• /
• pp.39-45
• /
• 2015

In this paper, variable rate CDR(Clock and Data Recovery) circuit adopting blind oversampling architecture is presented. The clock recovery circuit is implemented by using wide range voltage controlled oscillator and band selection method and the data recovery circuit is designed to digital circuit used majority voting method in order to low power and small area. The designed low power variable clock and data recovery is implemented by wide range voltage controlled oscillator and digital data recovery circuit. The designed variable rate CDR is operated from 10 bps to 2 Mbps. The total power consumption is about 4.4mW at 1MHz clock. The supply voltage is 1.2V. The designed die area is $120{\mu}m{\times}75{\mu}m$ and this circuit is fabricated in $0.13{\mu}m$ CMOS process.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.399-405
• /
• 2011

In this paper, we present the design of Q-band LC VCO and injection locking buffer for 77 GHz automotive radar sensor using 130 nm RF CMOS process. To improve the phase noise characteristic of LC tank, the transmission line is used. The negative resistance by the active device cross-coupled pair of buffer is used for high output power, with or without oscillation of buffer. The measured phase noise is -102 dBc/Hz at 1 MHz offset frequency and tuning range is 34.53~35.07 GHz. The output power is higher than 4.1 dBm over entire tuning range. The fabricated chip size is $510{\times}130\;um^2$. The power consumption of LC VCO is 10.8 mW and injection locking buffer is 50.4 mW from 1.2 V supply.

• ETRI Journal
• /
• v.36 no.2
• /
• pp.206-213
• /
• 2014

This paper presents a novel 90 GHz band 16-quadrature amplitude modulation (16-QAM) orthogonal frequency-division multiplexing (OFDM) communication system. The system can deliver 6 Gbps through six channels with a bandwidth of 3 GHz. Each channel occupies 500 MHz and delivers 1 Gbps using 16-QAM OFDM. To implement the system, a low-noise amplifier and an RF up/down conversion fourth-harmonically pumped mixer are implemented using a $0.1-{\mu}m$ gallium arsenide pseudomorphic high-electron-mobility transistor process. A polarization-division duplex architecture is used for full-duplex communication. In a digital modem, OFDM with 256-point fast Fourier transform and (255, 239) Reed-Solomon forward error correction codecs are used. The modem can compensate for a carrier-frequency offset of up to 50 ppm and a symbol rate offset of up to 1 ppm. Experiment results show that the system can achieve a bit error rate of $10^{-5}$ at a signal-to-noise ratio of about 19.8 dB.

• Journal of the Optical Society of Korea
• /
• v.6 no.3
• /
• pp.59-71
• /
• 2002

Photonic band gap structures have a high potential for nearly zero-threshold lasers. This paper describes new-types of low-threshold photonic crystal lasers fabricated in InGaAsP slab waveguides free-standing in air. Two-types of photonic crystal lasers are studied. One is a single-cell nano-cavity laser formed in a square array of air holes. This photonic band gap laser operates in the smallest possible whispering gallery mode with a theoretical Q >30000 and exhibits low threshold pump power of 0.8 mW at room temperature. The nther laser does not have any cavity structure and the lasing operation originates from the enhanced optical density of states near photonic band edges. A very low threshold of 35 $\mu$W (incident pump power) is achieved from this laser at 80 K, one of the lowest values ever reported. This low threshold is benefited from low optical losses as well as enhanced material gain at low temperature.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.1
• /
• pp.92-97
• /
• 2009

Low power consumption is crucial for medical implantable devices. A low-power 4th-order band-pass Gm-C filter with distributed gain stage for the sensing stage of the implantable cardiac pacemaker is proposed. For the implementation of large-time constants, a floating-gate operational transconductance amplifier with current division is employed. Experimental results for the filter have shown a SFDR of 50 dB. The power consumption is below $1.8{\mu}W$, the power supply is 1.5 V, and the core area is $2.4\;mm{\times}1.3\;mm$. The filter was fabricated in a 1-poly 4-metal $0.35-{\mu}m$ CMOS process.

• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.244-250
• /
• 2012

In this paper, worldwide standards and regulations on broadcasting services are reviewed to improve the fringe area of terrestrial DTV broadcasting services. Using these results, in-band/out-of-band emission requirements of low power DTV repeater with 10mW/MHz radiating power are proposed, and experimentally evaluated and verified. Using the proposed regulations, compact and cost-effective DTV repeater can be easily implemented to broaden DTV broadcasting coverage and to improve small/medium size DTV fringe areas.

• Journal of Korea Multimedia Society
• /
• v.10 no.4
• /
• pp.516-526
• /
• 2007

Wireless mesh network is not only WLAN technology but it says core technology for implementation of ubiquitous network and we have to application on a various field through connection with the sensor network. However, there are limited to 100mW in the maximum power because WLAN is used into transmission frequency band to ISM band. The mesh network based on WLAN is essential study for a long distance transmission in the limited maximum power that it is doing to cost-efficient network of backbone. Therefore, in this paper, we have presented an conquerable method to limitation of reaching distance of wireless mesh network and made several experiments to presentation the proposed method. The results show that it is possible to rise a long distance transmission and power efficiency into application of various antenna and function definition and implementation of device driver.