• Elastomers and Composites
• /
• 제53권4호
• /
• pp.213-219
• /
• 2018

The degradation mechanism and physical properties of an FKM O-ring were observed with thermal aging in this experiment. From X-ray photoelectron spectroscopy (XPS) analysis, we could observe carbon (285 eV), fluoro (688 eV), and oxygen (531 eV) peaks. Before thermal aging, the concentration of fluoro atoms was 51.23%, which decreased to 8.29% after thermal aging. The concentration of oxygen atoms increased from 3.16% to 20.39%. Under thermal aging, the FKM O-ring exhibited debonding of the fluoro-bond by oxidation. Analysis of the C1s, O1s, and F1s peaks revealed that the degradation reaction usually occurred at the C-F, C-F2, and C-F3 bonds, and generated a carboxyl group (-COOH) by oxidation. Due to the debonding reaction and decreasing mobility, the glass transition temperature of the FKM O-ring increased from $-15.91^{\circ}C$ to $-13.79^{\circ}C$. From the intermittent CSR test, the initial sealing force was 2,149.6 N, which decreased to 1,156.2 N after thermal aging. Thus, under thermal aging, the sealing force decreased to 46.2%, compared with its initial state. This phenomenon was caused by the debonding reaction and decreasing mobility of the FKM O-ring. The S-S curve exhibited a 50% increase in modulus, with break at a low strain and stress state. This was also attributed to the decreasing mobility due to thermal aging degradation.

• 한국추진공학회지
• /
• 제26권6호
• /
• pp.21-27
• /
• 2022

C_f/SiC 복합재는 저밀도, 높은 기계적 강도, 우수한 열 안정성을 가지고 있어 로켓 추진기관, 항공 및 군사 분야 등의 고온 응용 산업에 유망한 재료이다. 그러나 용융 실리콘 함침(Liquid Silicon Infiltration, LSI) 공정을 통해 제작된 복합재는 잔존하는 Si에 의하여 물리적, 열적 특성이 저하된다. 본 논문에서는 LSI 공정을 통해 제작된 C_f/SiC 복합재의 내부 Si을 제거하기 위한 방안으로 탈규소화(de-siliconization) 공정을 도입하였다. 최대 5분 동안 옥시아세틸렌 토치 테스트를 진행하고 시편의 산화된 표면과 단면은 3D scanning, X-ray diffraction(XRD), 광학현미경(OM), 전자주사현미경(SEM)으로 분석하였다.

• 한국수소및신에너지학회논문집
• /
• 제33권2호
• /
• pp.148-157
• /
• 2022

Research on hydrogen storage is active to properly deal with hydrogen, which is considered a next-generation energy medium. In particular, research on metal hydride with excellent safety and energy efficiency has attracted attention, and among them, magnesium-based hydrogen storage alloys have been studied for a long time due to their high storage density, low cost, and abundance. However, Mg-based alloys require high temperature conditions due to strong binding enthalpy, and have many difficulties due to slow hydrogenation kinetics and reduction in hydrogen storage capacity due to oxidation, and various strategies have been proposed for this. This research manufactured Mg₂Ni to improve hydrogenation kinetics and synthesize about 5, 10, 20 wt% of CaF₂ as a catalyst for controlling oxidation. Mg₂NiHx-CaF₂ produced by hydrogen induced mechanical alloying analyzed hydrogenation kinetics through an automatic PCT measurement system under conditions of 423 K, 523 K, and 623 K. In addition, material life cycle assessment was conducted through Gabi software and CML 2001 and Eco-Indicator 99' methodology, and the environmental impact characteristics of the manufacturing process of the composites were analyzed. In conclusion, it was found that the effects of resource depletion (ARD) and fossil fuels had a higher burden than other impact categories.

• Korean Chemical Engineering Research
• /
• 제45권6호
• /
• pp.656-662
• /
• 2007

고분자 전해질 연료전지 운전에 필요한 수소 공급 장치로서 플라즈마 개질 방법을 이용한 개질기와 일산화탄소 산화반응을 위한 전이 반응기를 설계 및 제작하였다. GlidArc 방전을 이용한 저온플라즈마 개질기는 Ni 촉매를 동시에 사용하여 $CH_4$ 개질함으로서 $H_2$ 선택도를 증대하였다. 개질기의 변수별 연구로서 촉매 온도, 가스 조성비, 전체 가스유량, 전압변화 그리고 개질 특성 및 최적 수소 생산조건을 연구하였으며, 전이반응기의 변수별 연구로서 선택적 산화반응기(PrOx)에 주입되는 공기량, 전이 반응기에 주입되는 수증기량 그리고 온도에 대하여 연구하였다. 플라즈마 개질기에서 최대 수소 생산 조건은 $O_2/C$ 비가 0.64, 가스유량은 14.2 l/min, 촉매 반응기 온도 $672^{\circ}C$ 그리고 유입전력이 1.1 kJ/L일 때 41.1%로 최대 수소 농도를 나타냈다. 그리고 이때의 $CH_4$ 전환율, $H_2$ 수율 그리고 개질기 에너지 밀도는 각각 88.7%, 54%, 35.2%를 나타냈다. 전이 반응기에서 모사된 개질 가스로부터 최대 CO 전환율을 보이는 조건은 2단으로 구성된 PrOx에 주입되는 $O_2/C$ 비가 0.3, HTS에서 주입되는 수증기 주입량 비가 2.8 그리고 HTS, LTS, PrOx I, PrOx II 반응기 온도가 475, 314, 260, $235^{\circ}C$ 일때 가장 높은 CO 전환율을 나타냈다. 플라즈마를 이용한 반응기는 예열 시간은 30분이 소요되었으며, 전이 반응기에서 나오는 최종 개질 가스의 조성은 $H_2$ 38%, CO<10 ppm, $N_2$ 36%, $CO_2$ 21% 그리고 $CH_4$ 4%로 나타냈다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.169-169
• /
• 2010

As display industry requires various applications for future display technology, which can guarantees high level of flexibility and transparency on display panel, oxide semiconductor materials are regarded as one of the best candidates. $InGaZnO_4$(IGZO) has gathered much attention as a post-transition metal oxide used in active layer in thin-film transistor. Due to its high mobility fabricated at low temperature fabrication process, which is proper for application to display backplanes and use in flexible and/or transparent electronics. Electrical performance of amorphous oxide semiconductors depends on the resistance of the interface between source/drain metal contact and active layer. It is also affected by sheet resistance on IGZO thin film. Controlling contact/sheet resistance has been a hot issue for improving electrical properties of AOS(Amorphous oxide semiconductor). To overcome this problem, post-annealing has been introduced. In other words, through post-annealing process, saturation mobility, on/off ratio, drain current of the device all increase. In this research, we studied on the relation between device's resistance and post-annealing temperature. So far as many post-annealing effects have been reported, this research especially analyzed the change of electrical properties by increasing post-annealing temperature. We fabricated 6 main samples. After a-IGZO deposition, Samples were post-annealed in 5 different temperatures; as-deposited, $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$ and $500^{\circ}C$. Metal deposition was done on these samples by using Mo through E-beam evaporation. For analysis, three analysis methods were used; IV-characteristics by probe station, surface roughness by AFM, metal oxidation by FE-SEM. Experimental results say that contact resistance increased because of the metal oxidation on metal contact and rough surface of a-IGZO layer. we can suggest some of the possible solutions to overcome resistance effect for the improvement of TFT electrical performances.

• Korean Chemical Engineering Research
• /
• 제60권4호
• /
• pp.620-629
• /
• 2022

가열 속도, 몰 공간속도, 질화반응온도 등 다양한 실험 조건을 변화하며 바나디움 산화물과 암모니아와의 승온 질화반응을 통하여 바나디움 산화질화물을 제조하여 특성분석을 수행하였으며 제조된 바나디움 산화질화물 상에서 암모니아 분해반응의 촉매 활성을 검토하였다. 제조된 촉매의 물리·화학적 특성을 알아보기 위하여 N₂ 흡착분석, X-선 회절분석(XRD), 수소 승온환원(H₂-TPR), 산소 존재 하 승온산화 (TPO), 암모니아 탈착 (NH₃-TPD), 투과전자현미경(TEM) 분석을 수행하였다. 340 ℃에서 5 m² g^-1의 낮은 비표면적을 갖는 V₂O₅의 환원에 의하여 V₂O₃ 으로의 변환은 미세 기공 형성에 의해 115 m² g^-1 높은 비표면적 값을 보여주었으며 그 이상의 질화반응 온도가 증가함에 따라 소결현상에 의해 지속적인 비표면적의 감소를 초래하였다. 비표면적에 가장 큰 영향을 미치는 질화반응 변수는 반응온도였으며, 단일 상의 VN_xO_y의 x + y 값은 질화반응온도가 증가함에 따라 1.5에서 1.0으로 근접하였으며 680 ℃의 높은 반응온도에서 입방 격자상수 a는 VN 값에 근접하였다. 본 실험 조건 중에 질화반응온도가 가장 높았던 680 ℃에서 암모니아 전환율은 93%로 나타났으며 비활성화는 관찰되지 않았다.

• 에너지공학
• /
• 제25권1호
• /
• pp.76-85
• /
• 2016

본 연구에서는 병참연료인 가솔린을 연료프로세서의 연료로 선택하여 광범위한 온도범위에서도 적용가능한 시동 및 제어 전략을 제시하였다. 가솔린 연료프로세서는 시동 초기 단계에서 연소 방식으로 상온상태의 자열개질기 촉매를 라이프온도까지 가열시킨다. 안정적인 가솔린-공기 혼합기체의 점화를 위하여 유동방향 기준 촉매 하단에 글로우 플러그를 설치하였다. 자열개질기가 촉매반응을 시작하면 가솔린 연료프로세서의 개질기는 정상상태까지 POX 모드, 부분 ATR 모드, 완전 ATR 모드 순으로 운전된다. 최종적으로 확립된 시동 및 제어 전략은 상온 및 저온 환경에서 가솔린 연료프로세서의 실제 실험을 통해 타당성을 확인하였다. 그 결과 가솔린 연료프로세서는 상온 및 저온에서 40분 이내에 정상상태에 도달하여 수소 37 ~ 42 vol.%(dry basis), 일산화탄소 0.3 vol.%의 개질가스를 생성할 수 있었다.

• 한국세라믹학회지
• /
• 제28권9호
• /
• pp.667-674
• /
• 1991

In this study, Kaolin was carbonized at 1300~175$0^{\circ}C$ and its constituent mineral change was investigated. Carbonized kaolin at 1$650^{\circ}C$ was mixed with metallic silicon, formed and nitrified at 135$0^{\circ}C$ in N2-NH3 atmosphere. Properties of this product such as porosity, bulk density, MOR, nitrization rate and oxidation resistence were measured, and its mineralogical changes were investigated by XRD. The results were as follows; 1) $\beta$-SiC was initially synthesized at 150$0^{\circ}C$, and its amount was continuously increased with reaction temperature to 1$700^{\circ}C$. 2) At 1$600^{\circ}C$, mullite was rapidly decomposed and the amounts of $\beta$-SiC and $\alpha$-Al2O3 were increased simultaneously. 3) By adding alkali to kaolin, the decomposition temperature of mullite was dropped approximately 10$0^{\circ}C$, but the amount of $\alpha$-SiC was increased. 4) The highest values of their nitrization rate and MOR were obtained at the specimen of 35 wt% metallic silicon in nitrization reaction. 5) It seems that increment of $\alpha$-Si3N4 and $\alpha$-Al2O3 phase during nitrization was due to the decomposition of Al4SiC4 existed in carbonized kaolin. 6) Si3N4 bonded SiC-Al2O3 composite were fabricated from kaolin at relatively low temperature (135$0^{\circ}C$).

• 한국수산과학회지
• /
• 제9권2호
• /
• pp.111-119
• /
• 1976

Discoloration of canned boiled oyster namely greening, yellowing and browning often occur separately or associatively in the storage of the product. Greening is mainly caused by the appearance of chlorophyll and its derivatives on the surface around the digestive diverticula of the oyster and yellowing by dispersion of carotenoid. Browning reactions by sugar amino condensation or enzymatic action, tyrosinase, also cause an undesirable color development. In this paper, the stability and the changes in distributional or partitional ratio of chlorophyll and carotenoid pigment of meat vs viscera in raw and canned oyster during six month storage in order to measure the dispersion rate of both pigments between meat and viscera, and to evaluate the feasibility of discoloration of oyster meat. The development of brownish pigment and the toss of free tyrosine in oyster were also determined to compare the readiness of color development. In addition the influence of processing and storage conditions to the dispersion rate and the tendency of discoloration, and finally the effect of inhibitor were discussed. The results showed that greening or yellowing was initiated by the dispersion of chlorophyll or carotenoids from viscera to the meat of oyster, and the dispersion rate of carotenoid was much higher than the chlorophyll's, so that, yellowing appeared a leading reaction of discoloration. The dispersion rate was obviously fastened by raising the temperature in the process of sterilization and storage. Consequently, the low temperature storage could largely retard the occurance of yellowing or greening of oyster meat. The pH control of canned oyster did not seem to affect the dispersion of pigment but significantly did on the stability of the piqments. Browning by the reaction of sugar-amino condensation and enzymatic oxidation of tyrosine was positively detected in canned oyster meat. The development of brownish color was influenced rather by the storage temperature than the heating process. Addition of sodium sulfite in can or treating the boiled oyster with sulfite solution prior to filling seemed possibly inhibit the color development particularly in cold-storaged oyster meat.

• 한국전기전자재료학회논문지
• /
• 제18권6호
• /
• pp.554-559
• /
• 2005

Ni/Cr thin film is very interesting material as thin film resistors, filaments, and humidity sensors because their relatively large resistivity, more resistant to oxidation and a low temperature coefficient of resistance (TCR). These interesting properties of Ni/Cr thin films are dependent upon the preparation conditions including the deposition environment and subsequent annealing treatments. Ni/Cr thin films of 250 nm were deposited by DC magnetron sputtering on $Al_2O_3/Si$ substrate with 2-inch Ni/Cr (80/20) alloy target at room temperature for 45 minutes. Annealing treatments were performed at $400^{\circ}C,\;500^{\circ}C,\;and\;600^{\circ}C$ for 6 hours in air or $H_2$ ambient, respectively. The clear crystal boundaries without crystal growth and the densification were accomplished when the pores were disappeared in air ambient. Most of surface was oxidic including NiO, $Ni_2O_3$ and $Cr_xO_y$(x=1,2, y=2,3) after annealing in air ambient. The crystal growth in $H_2$ ambient was formed and stabilized by combination with each other due to the suppression of oxidized substance on film surface. Most oxidic Ni was restored when the oxidic Cr was present due to its stability in high-temperature $H_2$ ambient.