• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.1
• /
• pp.122-127
• /
• 2016

In this paper, new spectrum sensing schemes based on analog/RF front-end processing are introduced for IoT wireless sensor networks. While the conventional approaches for wireless channel cognition have been issued in signal processing area, the RF spectrum cognition concept makes it feasible to achieve cognitive wireless sensor networks (C-WSNs). The spectrum cognition at RF processing is categorized as four kinds of sensing mechanisms. Two recent reseaches are described as promising candidates for the C-WSN. One senses spectrum by the frequency discriminating receiver, the other senses and detects from the frequency selective super-regenerative receiver. The introduced systems with simple and low-power RF architectures play dual roles of channel sensing and demodulation. simultaneously. Therefore, introduced spectrum sensing receivers can be one of the best candidates for IoT wireless sensor devices in C-WSN environments.

• Electronics and Telecommunications Trends
• /
• v.9 no.4
• /
• pp.113-129
• /
• 1994

우리나라에서는 전파법 시행령 제56조의 2항과 무선 설비 규격 제4절 및 관련 고시를 통하여 소출력 무선 설비들을 규정하고 있으나 대상 설비 중 극히 일부분만 세부적인 기술 기준이 설정되어 있는 실정이다. 따라서 이러한 소출력 무선기기 상호간의 혼신이나 타 기기와의 간섭으로 인하여 전파 질서의 안정에 위협받을 가능성이 있다. 본 고에서는 이와 같은 문제를 최소화하기 위해 미국의 소출력 무선기기에 대한 제도 및 표준 규격을 조사 조사분석하여 우리나라와 비교함으로써 국내 무선기기 관련 제도의 체계적 정립과 소출력 무선 설비의 형식 검정을 위한 표준 측정법의 정립에 기여하고자 한다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.6
• /
• pp.630-639
• /
• 2008

In this paper, we investigate the cause of throughput degradation on the wireless local area network(WLAN) and the reason of interference level change attributed to the spanned frequency in the presence of electromagnetic interference. We also measured and quantified the electric field strength of interference which yields the abrupt change of the throughput. Two units of WLAN and one unit of AP(Access Point) are configured to maintain the radio link. As the sources of interference, both the co-channel and adjacent-channel interference are considered and the critical values of electric field are provided for each case. Our experimental observations show that the signal strength generated from these interference sources is at most less than 54 dBuV/m @3 m in order to coexist between WLANs and other low power radio devices without any noticeable throughput decreases. Based on our empirical results, as far as 802.11b WLAN is concerned, we believe that the current domestic limit of the signal strength for an extremely low power radio device, 30.9 dBuV/m @3 m, can be increased as much as 23.1 dB.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.7
• /
• pp.609-614
• /
• 2015

Implanted telemetry systems provide the ability to monitor different species of animals while they move within their cages. Species monitored include mice, rats, rabbits, dogs, pigs, primates, sheep, horses, cattle, and others. A miniature transmitter implanted in each animal measures one or more parameters. Parameters measured include arterial pressure, intra-pleural pressure, left ventricular pressure, intra-ocular pressure, bladder pressure, ECG, EMG, EEG, EOG, temperature, activity, and other parameters and transmits the data via radio frequency signals to a nearby receiver. Every conventional dedicated transmitter contains one or more sensors, cpu and battery. Due to the expected life of the battery, the measuring time is limited. To overcome these problems, electromagnetic inductive coupling based wireless power transmission technology using multiple transmit coils were proposed, with each coil having a different active area driven by the coil driver. In this research, a parallel resonance based coil driver and serial resonance based coil driver are proposed. From the experiments we see that the parallel coil driver shows better performance under a low impedance and multiple coils configuration. However, the serial coil driver is more efficient for high impedance transmit coils.

• Journal of Sensor Science and Technology
• /
• v.16 no.2
• /
• pp.142-149
• /
• 2007

Wireless sensor network technology is an emerging technology consisting of small, low power, and low cost devices that integrate limited computation, sensing, and radio communication capabilities. An ad-hoc home network system based embedded system for home environment monitoring was fabricated and tested. The wireless sensor node consists of a MCU, RF transceiver and sensors (temperature, humidity and light). Wireless sensor nodes run application software for data sampling and wireless communication, that was developed using 'nesC language' which runs on TinyOS. In our tests, acquired sensors data were monitored on 6.4" TFT-LCD of base-station through IEEE802.15.4 standard wireless communication. Also, the sensor data can be monitored by client user at the terminal PC to monitor environmental status of home in real time.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.3
• /
• pp.166-176
• /
• 2007

Radio frequency (RF) microelectromechanical systems (MEMS) have been pursued for more than a decade as a solution of high-performance on-chip fixed, tunable and reconfigurable circuits. This paper reviews our research work on RF MEMS switches and switching circuits in the past five years. The research work first concentrates on the development of lateral DC-contact switches and capacitive shunt switches. Low insertion loss, high isolation and wide frequency band have been achieved for the two types of switches; then the switches have been integrated with transmission lines to achieve different switching circuits, such as single-pole-multi-throw (SPMT) switching circuits, tunable band-pass filter, tunable band-stop filter and reconfigurable filter circuits. Substrate transfer process and surface planarization process are used to fabricate the above mentioned devices and circuits. The advantages of these two fabrication processes provide great flexibility in developing different types of RF MEMS switches and circuits. The ultimate target is to produce more powerful and sophisticated wireless appliances operating in handsets, base stations, and satellites with low power consumption and cost.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.6
• /
• pp.202-207
• /
• 1997

Design and fabrication issues for an L-band GaAs Monolithic Microwave Integrated Circuit(MMIC) Voltage Controlled Oscillator(VCO) as a component of Personal Communications Systems(PCS) Radio Frequency(RF) transceiver are discussed. An ion-implanted GaAs MESFET tailored toward low current and low noise with 0.5mm gate length and 300mm gate width has been used as an active device, while an FET with the drain shorted to the source has been used as the voltage variable capacitor. The principal design was based on a self-biased FET with capacitive feedback. A tuning range of 140MHz and 58MHz has been obtained by 3V change for a 600mm and a 300mm devices, respectively. The oscillator output power was 6.5dBm wth 14mA DC current supply at 3.6V. The phase noise without any buffer or PLL was 93dB/1Hz at 100KHz offset. Harmonic balance analysis was used for the non-linear simulation after a linear simulation. All layout induced parasitics were incorporated into the simulation with EEFET2 non-linear FET model. The fabricated circuits were measured using a coplanar-type probe for bare chips and test jigs with ceramic packages.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.8
• /
• pp.744-751
• /
• 2004

This paper presents the implementation of the low cost and high speed RF ATE(Automatic Test Equipment) system, which can be a reasonable solution for reducing the test cost of RF devices. This paper suggests high speed and precise measurement capabilities which are realized by the 16 independent RF ports with high speed switching time and high accuracy digitizer using the industry standard Versus module eXtensions for Instrument(VXI) General Purpose Interface Bus(GPIB) interfaces. Also, the system has the capabilities of quad-site test which can dramatically increase the device throughput. This paper concludes with the demonstration of the implemented ATE system through the setup of RF Power Amplifier Module(PAM), which is under the most competitive market situation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.2C
• /
• pp.238-245
• /
• 2010

For orthogonal frequency division multiplexing (OFDM) systems sharing the spectrum with narrow band primary devices, a fractional bandwidth (FBW) mode has been proposed recently to reduce the interference to the primary users. The FBW mode divides the total OFDM bandwidth into subbands and activates (or deactivates) a subset of the subbands according to the result of spectrum sensing. In this paper, we analyze the detection error probability of FBW mode information which is delivered by the sequence embedded in the preamble and evaluate the performance in wireless regional area network environments. The results show that the detection probability derived analytically estimates the actual value from simulation adequately and that a low detection error probability less than $10^{-3}$ is obtained at a low signal-to-noise power ratio.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.5
• /
• pp.371-378
• /
• 2015

In this paper, a different type of pulse width modulation (PWM) control scheme for a buck converter is introduced. The proposed buck converter uses PWM with frequency hopping and a low quiescent.current low dropout (LDO) voltage regulator with a power supply rejection ratio enhancer to reduce high spurs, harmonics and output voltage ripples. The low quiescent.current LDO voltage regulator is not described in this paper. A three-bit binary-to-thermometer decoder scheme and voltage ripple controller (VRC) is implemented to achieve low voltage ripple less than 3mV to increase the efficiency of the buck converter. An internal clock that is synchronized to the internal switching frequency is used to set the hopping rate. A center frequency of 2.5MHz was chosen because of the bluetooth low energy (BLE) application. This proposed DC-DC buck converter is available for low-current noise-sensitive loads such as BLE and radio frequency loads in portable communications devices. Thus, a high-efficiency and low-voltage ripple is required. This results in a less than 2% drop in the regulator's efficiency, and a less than 3mV voltage ripple, with -26 dBm peak spur reduction operating in the buck converter.