• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.1
• /
• pp.59-67
• /
• 2016

A novel instrumentation amplifier (IA) using fully-differential linear operational transconductance amplifier (FLOTA) for electronic measurement systems with low cost, wideband, and gain control with wide range is designed. The IA consists of a FLOTA, two resistor, and an operational amplifier(op-amp). The principal of the operating is that the difference of two input voltages applied into FLOTA converts into two same difference currents, and then these current drive resistor of (+) terminal and feedback resistor of op-amp to obtain output voltage. To verify operating principal of the IA, we designed the FLOTA and realized the IA used commercial op-amp LF356. Simulation results show that the FLOTA has linearity error of 0.1% and offset current of 2.1uA at input dynamic range ${\pm}3.0V$. The IA had wide gain range from -20dB to 60dB by variation of only one resistor and -3dB frequency for the 60dB was 10MHz. The proposed IA also has merits without matching of external resistor and controllable offset voltage using the other resistor. The power dissipation of the IA is 105mW at supply voltage of ${\pm}5V$.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.4
• /
• pp.715-720
• /
• 2012

This study presents a hybrid balanced voltage controlled oscillator (VCO) circuit which is suitable for low phase noise operation at sub-1V supply voltages. Half circuits of the proposed VCO use the varactor-integrated feedback capacitors in their respective circuit. The varactor-integrated feedback capacitors further increase the negative resistance of the equivalent tank thereby ensuring stable start-up of oscillation even at the sub-1V supply voltage. In addition, this work theoretically analyses the phenomenon of the increase of the negative resistance. Simulation results using a $0.18{\mu}m$ RF CMOS technology exhibit the phase noises of -122.4 to -125.5.8 dBc/Hz at 1 MHz offset from oscillation frequency of 4.87 GHz over the supply voltages of 0.6 through 0.9 V.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.5
• /
• pp.1310-1318
• /
• 1998

Sigma-delta converter is frequently used for conyerting low-frequency anglog to digital signal. The converter consists of a modulator and a digital filer, but our work is concentrated on the modulator. In this works, to design second-order sigma-dalta modulator with 14bit resolution, we define maximumerror limits of each components (operational smplifier, integrator, internal ADC, and DAC) of modulator. It is first performed modeling of an ideal second-order sigma-delta modulator. This is then modified by adding the non-ideal factors such as limit of op-amp output swing, the finit DC gain of op-amp slew rate, the integrator gian error by the capacitor mismatch, the ADC error by the cmparator offset and the mismatch of resistor string, and the non-linear of DAC. From this modeling, as it is determined the specification of each devices requeired in design and the fabrication error limits, we can see the final performance of modulator.

• Journal of Satellite, Information and Communications
• /
• v.10 no.2
• /
• pp.109-114
• /
• 2015

Frame synchronization is achieved by correlation between received symbols and a preamble pattern which is periodically appended at a frame header. In this paper, we deal with a frame detection method complaint with satellite-based DVB-S2 system. In DVB-S2, frame synchronization is performed under the low signal-to-noise ratio(SNR), a large frequency offset which can be up to 20% of a symbol transmission rate and unknown modulation schemes ranging from QPSK to 32-APSK. In this environment, we propose a method combining differential correlation based on SOF and PLSC with an accumulated correlation method for the detection of frame structures. In addition, detection performances about mean acquisition time(MAT) and detection error probability are evaluated via computer simulations.

• Journal of Navigation and Port Research
• /
• v.27 no.5
• /
• pp.513-517
• /
• 2003

In this paper, a VCDRO(Voltage Control Dielectric Resonator Oscillator} applied to X-band as stable source is implementea and constructed with a MESFET for low noise, a dielectric resonator of high frequency selectivity and high Q varactor diode to obtain a good phase noise performance and stable sweep characteristics. The designed circuits is simulated through the harmonic balance simulation technique to provide the optimum performance. The measured results of a fabricated VCDRO show that output is 2.22dBm at 12.05GHz. harmonic suppression -30dBc. phase noise -130dBc at 100kHz offset. and sweep range of varactor diode $\pm$18.7MHz. respectively. This oscillator will be available to X-band application.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.4
• /
• pp.393-400
• /
• 2014

In this paper, we have designed the transmitter for earth station terminal operating with military geostationary satellite on Ka-band that is complied with MIL-STD-188-164A. The designed antenna of this terminal is dual-offset gregorian reflector which is consist of corrugated horn and iris polarizer, othermode transducer. This antenna meets radiation pattern and transmit EIRP spectral density requirements in this standard. The designed RF systems of this terminal are consist of Block Up Converter(BUC) converting frequency band from IF to Ka band and SSPA having low-power consumption and compact light-weight using the pHEMT MMIC compound devices. This RF systems applied with VSWR, spurious/harmonic suppression, output flatness and phase noise requirement in this standard.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.1
• /
• pp.38-46
• /
• 2012

In this paper, we propose a decision feedback equalizer based on LDPC(Low Density Parity Check) code for the fast processing and performance improvement in OFDM system. LDPC code has good error correcting capability and its performance approaches the Shannon capacity limit. However, it has longer parity check matrix and needs more iteration numbers. In our proposed system, MSE(Mean Square Error) of signal between decision device and decoder is fed back to equalizer. This proposed system can improve BER performance because it corrects estimated channel response more accurately. In addition, the proposed system can reduce complexity because it has a lower number of iterations than system without feedback at the same performance. Simulation results evaluate and show the performance of OFDM system with the CFO and phase noise in multipath channel.

• Journal of Ocean Engineering and Technology
• /
• v.34 no.5
• /
• pp.285-293
• /
• 2020

This study evaluated the Hook-up installation of an offshore site construction process, which is the final step in an offshore site installation process. During Hook-up installation, the offshore structure can have a detrimental effect on the work stability due to low-frequency motion. Moreover, economic costs can be incurred by the increase in available days of a tugboat. Therefore, this study developed a numerical analysis program to assess the dynamic behavior of mooring systems during hook-up installation to analyze the generally performed installation process and determine when the tugboat should be released. In this program, the behavior of an offshore structure was calculated using Cummin's time-domain motion equation, and the mooring system was calculated by Lumped mass method (LMM). In addition, a tugboat algorithm for hook-up installation was developed to apply the Hook-up procedure. The model used in the calculations was the barge type assuming FPSO (Floating production storage and off-loading) and has a taut mooring system connected to 16 mooring lines. The results of the simulation were verified by comparing with both MOSES, which is a commercial program, and a calculation method for restoring coefficient matrix, which was introduced by Patel and Lynch (1982). Finally, the offset of the structure according to the number of tugboats was calculated using the hook-up simulation, and the significant value was used to represent the calculation result.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.569-572
• /
• 2014

This paper presents a CMOS switched-capacitor interface circuit for MEMS capacitive sensors. It consist of a capacitance to voltage converter(CVC), a second-order ${\Sigma}{\Delta}$ modulator, and a comparator. A bias circuit is also designed to supply constant bias voltages and currents. This circuit employes the correlated-double-sampling(CDS) and chopper-stabilization(CHS) techniques to reduce low-frequency noise and offset. The designed CVC has a sensitivity of 20.53mV/fF and linearity errors less than 0.036%. The duty cycle of the designed ${\Sigma}{\Delta}$ modulator output increases about 5% as the input voltage amplitude increases by 100mV. The designed interface circuit shows linearity errors less than 0.13%, and the current consumption is 0.73mA. The proposed circuit is designed in a 0.35um CMOS process with a supply voltage of 3.3V. The size of the designed chip including PADs is $1117um{\times}983um$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.55-64
• /
• 2006

This work proposes a calibration-free 14b 70MS/s 0.13um CMOS ADC for high-performance integrated systems such as WLAN and high-definition video systems simultaneously requiring high resolution, low power, and small size at high speed. The proposed ADC employs signal insensitive 3-D fully symmetric layout techniques in two MDACs for high matching accuracy without any calibration. A three-stage pipeline architecture minimizes power consumption and chip area at the target resolution and sampling rate. The input SHA with a controlled trans-conductance ratio of two amplifier stages simultaneously achieves high gain and high phase margin with gate-bootstrapped sampling switches for 14b input accuracy at the Nyquist frequency. A back-end sub-ranging flash ADC with open-loop offset cancellation and interpolation achieves 6b accuracy at 70MS/s. Low-noise current and voltage references are employed on chip with optional off-chip reference voltages. The prototype ADC implemented in a 0.13um CMOS is based on a 0.35um minimum channel length for 2.5V applications. The measured DNL and INL are within 0.65LSB and l.80LSB, respectively. The prototype ADC shows maximum SNDR and SFDR of 66dB and 81dB and a power consumption of 235mW at 70MS/s. The active die area is $3.3mm^2$.