• 전기학회논문지
• /
• 제56권5호
• /
• pp.892-897
• /
• 2007

This paper presents the output filter design and the output characteristic analysis by cut-off frequency set up of the LCR filter on NPC multi-level inverter with trap-filter. The single-phase NPC three-level inverter operates at low switching frequency. The proposed LC trap filter is comprised of a conventional LCR output filter, by using LC trap filter the need for high damping resistor and low LC cut-off frequency is eliminated. Also. low damping resistor is increased the output filter system. The multilevel inverter system used NPC type inverter in proper system for high power application and controller is used DSP(TMS320C31). The effectiveness of proposed system confirmed the validity through SPICE simulation and experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2522-2525
• /
• 1999

Buck converter is considered to be one of the most widely used DC-DC converters due to its simple structure and high reliable performance. However, when it be combined with thin-film inductor, its own low inductance requires higher switching frequency in order to maintain optimum output ripple voltage and thus gives rise to extra switching losses. In view to overcoming such a technical in-convenience, soft switching fashion is suggested such as zero-voltage-switching of which an well known example is a Zero-Voltage-Switching clamp voltage(ZVS-CV) converter for which low inductance is imperatively required for ZVS operation. In order to support our suggestion, a 1W of ZVS-CV buck converter( Vo=3.3V, Iomax=0.3A, fs= 1.2MHz) is built by use of thin-film inductor, and then tested for comparing the measured efficiency between ours and conventional one. As the our results. the efficiency is improved about 2% at full load by the application of our concept.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2014년도 전력전자학술대회 논문집
• /
• pp.431-432
• /
• 2014

Recently, the demand of LED(light-emitting diode) lighting is gradually enlarged by governmental saveenergy policy, which the LED lighting has been established compulsorily in new buildings, public institutions, and residential installations etc.. The LED lighting is driven by SMPS (switching mode power supply). The SMPS requires high efficiency because the SMPS changes a commercial ac power source to low voltage dc power source. Harmonic components that occur in the conversion process of SMPS decrease system power factor and deal great damage in electric power system. To improve such problems, this paper proposes a SMPS of high efficiency. The switching devices in the proposed SMPS are operated by soft switching technique using a new quasi-resonant circuit. The input ac current waveform in the proposed SMPS becomes a quasi-sinusoidal waveform proportional to the magnitude of input ac voltage under constant switching frequency. As a result, the proposed SMPS obtains low switching power loss and high efficiency, and its input power factor is nearly in unity.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2016년도 전력전자학술대회 논문집
• /
• pp.107-108
• /
• 2016

Solid State Transformer(SST) has been recently regarded as a good alternative to conventional low frequency transformer. SST is consist of several high voltage power stage, so it is important to select optimal semiconductor switches for specification. This paper presents optimal IGBT switches for low switching losses using analyzing switching characteristics of several high voltage IGBT switches. Double Pulse Tester(DPT) experiment is used to verify characteristics of this IGBT switches.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1990년도 추계학술대회 논문집 학회본부
• /
• pp.332-335
• /
• 1990

There are several methods in controlling resonant converters to regulate the output with low switching losses. In this paper, Pulse-width modulation method or current controlled method is applied to regulate the output with low switching losses. In digital implementation of resonant converter systems, the speed of the applied processor is very critical since the switching frequency is very high. Thus the various possible candidates of microprocessors are evaluated for the implementation of resonant converter systems. Then too design methods and techniques are desioribed when single chip processor is used to simplify hardware requirements.

• ETRI Journal
• /
• 제40권5호
• /
• pp.592-603
• /
• 2018

In order to obtain better target identification performance, an efficient waveform design method with high range resolution and low sidelobe level for orthogonal frequency division multiplexing (OFDM) multiple-input multiple-output (MIMO) radar is proposed in this paper. First, the wideband CP-based OFDM signal is transmitted on each antenna to guarantee large bandwidth and high range resolution. Next, a complex orthogonal design (COD) is utilized to achieve code domain orthogonality among antennas, so that the spatial diversity can be obtained in MIMO radar, and only the range sidelobe on the first antenna needs suppressing. Furthermore, sidelobe suppression is expressed as an optimization problem. The integrated sidelobe level (ISL) is adopted to construct the objective function, which is solved using the Broyden-Fletcher-Goldfarb-Shanno (BFGS) algorithm. The numerical results demonstrate the superiority in performance (high resolution, strict orthogonality, and low sidelobe level) of the proposed method compared to existing algorithms.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1296-1299
• /
• 2000

A single stage AC/DC converter based on a full bridge topology suitable for high frequency soft switching converter applications is proposed. The proposed converter has high power factor, zero voltage switching, low noise and high efficiency. A pulse width modulation control is employed to reduce the switching and rectification losses respectively. This proposal converter has simple structure and low cost, The modelling and detailed analysis are performed to derive the design equations, a prototype converter has been designed and experimented. The new converter is attractive for high-voltage, high-power applications where IGBT's are predominantly used as the power switches. The principle of operation, features, and design are verified on a 1.5kW, 30kHz, IGBT based experimental circuit.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권6호
• /
• pp.359-367
• /
• 2004

The switched reluctance motor(SRM) has considerable potential for industrial applications because of its high result lily as a result of the absence of rotor windings. In some applications with SRM, paralleling strategy is often used for cost saving, increasing of current capacity and system reliability. A SRM inverter has very low ,switching frequency. This results in reducing the burden for a high-speed of the gate-amp interface circuit. and the linearity of optocoupler is used to protect the instantaneous peak current for the stable operation. In this paper, series resistor is used to equal the current sharing of each switching device and a linear gate-amp is proposed to protect the instantaneous peak current which occurs in transient state. The proposed paralleling strategy is verified by experimental results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.193-197
• /
• 2001

This paper presents a novel circuit topology of the double two-switch forward type high frequency transformer linked soft-switching PWM DC-DC power converter with tapped inductor filters that can operate under a condition of the low peak voltage stress across the power semiconductor devices and lowered peak current stress through the transformer for some high power applications. This circuit topology of an interleaved two-switch forward soft-switching power converter is proposed in the order to minimize an idle circulating current due to the tapped inductor filter without of any additional active auxiliary resonant-assisted snubber circuits, such as active resonant DC link snubbers and AC link snubbers, active resonant commutation leg link snubbers. The unique advantages of this power converter are less power circuit components and power semiconductor devices, constant frequency PWM scheme, cost effective configuration and wider soft-switching PWM operation range under PWM power regulations load variations. The practical effectiveness of the proposed soft-switching converter circuit topology is tested by simulations and is proved by experimental results received from the 500W-100kHz breadboard setup.

• Journal of Power Electronics
• /
• 제18권4호
• /
• pp.985-996
• /
• 2018

The implementation and performance evaluation of an interleaved boundary conduction mode (BCM) boost power factor correction (PFC) converter is presented in this paper by employing three wide band-gap switching devices: a super junction silicon (Si) MOSFET, a silicon carbide (SiC) MOSFET and a gallium nitride (GaN) high electron mobility transistor (HEMT). The practical considerations for adopting wide band-gap switching devices to BCM boost PFC converters are also addressed. These considerations include the gate drive circuit design and the PCB layout technique for the reliable and efficient operation of a GaN HEMT. In this paper it will be shown that the GaN HEMT exhibits the superior switching characteristics and pronounces its merits at high-frequency operations. The efficiency improvement with the GaN HEMT and its application potentials for high power density/low profile BCM boost PFC converters are demonstrated.