• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.57-63
• /
• 2009

In this Paper, a novel 622Mbps burst-mode clock and data recovery (CDR) circuit is proposed for passive optical network (PON) applications. The CDR circuit is composed of CDR(Clock and Data Recovery) block and PLL(Phase Locked Loop) block. Lock dynamics is accomplished on the first data transition and data are sampled in the optimal point. The CDR circuit is realized in 0.35um CMOS process technology. With input pseudo-random bit sequences(PRBS) of $2^7-1$, the simulations show 17ps peak-to-peak retimed data jitter characteristics. The experimental results show that the proposed CDR circuits are operating as expected, recovering an incoming 622Mbps burst-mode input data without errors.

• Journal of the Korean Society of Costume
• /
• v.57 no.2 s.111
• /
• pp.1-10
• /
• 2007

This study aims at the improvement of sewing function through understandings of dynamic property about the sewing methods and the thread material selection in knitwear. The tensile strength and shear of KES-FB and the Instron were measured for the analysis of the mechanical properties. The knit cloth was structured In the plain stitch, $1\times1$ rib stitch and $2\times1$ rib stitch with the combination of wool and cotton. With regard to the sewing method, intralooping and interlacing were applied. For thread materials, polyester, cotton, wool and silk were used. Since silk has the lowest extension and similar values regardless of its construction in intralooping, it is available knit apparel with uniform elastic recoverv. It also has small shearing resistance. It can be used in apparel which needs big mobility, but it causes rutting problem. Therefore, it is suitable to use intralooping. When the same sewing yarn and textile are use, it can lower shearing resistance and extension in intralooping, Since wool needs a lot of extension energy and it can be cut, intralooping is more suitable than interlacing in sewing of wool. In interlacing using polyester, extension and shearing resistance are high. Therefore, it is suitable for knit sewing with high massing. Silk is not suitable for interlacing since it can be rut. Even though knit materials are different, the RT values of polyester and cotton are similar in same construction. Therefore, they can be substituted each other considering resilience after sewing.

• Korean Journal of Optics and Photonics
• /
• v.15 no.6
• /
• pp.569-574
• /
• 2004

We stabilized the frequency and power of a CW radio-frequency-excited $CO_2$ laser on the peak of the Doppler broadened gain curve using the photoacoustic effect generated from the laser itself. The condenser microphone is installed in the radio frequency discharge chamber to detect a photoacoustic signal. The photoacoustic signal is fed to a lock-in stabilizer as a reference signal for stabilization. The frequency stability is estimated to be better then 5.4${\times}$10$^{-8}$ at the P(20) line. The stabilized output variation was reduced 9.3%, compared to 100% for a free running laser.

• Journal of Science and Technology Studies
• /
• v.8 no.2
• /
• pp.57-81
• /
• 2008

This paper reviewed outline of Strategic Niche Management(SNM) and its usefulness and limits as policy tool. SNM is based on Multi Level Perspective(MLP) that traces technological innovation and makes transition of lock-in socio-technical system. This approach is one of systematical then traditional one, market failure approach. SNM had get a attention not only as a analytical frame of technological development, but also tool of radical innovation, although its limits of theoretical and empirical immaturity. SNM could provide a new perspective to analysis and action within urgent needs of alternative innovation policy for aging society, news energy policy for sustainable and disaster policy in danger society.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.865-871
• /
• 2016

This work presents a radar signal interferer to be used for evaluating the mutual interference among automotive radars. The developed interfering signal generator is composed of a reference signal generator and a 77 GHz transmitter. Reference signal generator is made up of commercial chips and board, it can generate various modulated signal such as triangular wave, sawtooth wave and random frequency hopping. The transmitter generates 77 GHz band signal by multiplying modulated reference signal frequency 28 times. Transmitter was fabricated using 65 nm CMOS process, it can operate horn antenna by built in on-chip waveguide feeder. The transmitter exhibited 7.31~8.06 dBm output power over a frequency lock range of 75.6~77 GHz.

• Journal of KIISE:Computing Practices and Letters
• /
• v.14 no.5
• /
• pp.542-546
• /
• 2008

Recently dual-port SDRAM (DPSDRAM) architecture tailored for dual-processor based mobile embedded systems has been announced where a single memory chip plays the role of the local memories and the shared memory for both processors. In order to maintain memory consistency from simultaneous accesses of both ports, every access to the shared memory should be protected by a synchronization mechanism, which can result in substantial access latency. We propose two optimization techniques by exploiting the communication patterns of target applications: lock-priority scheme and static-copy scheme. Further, by dividing the shared bank into multiple blocks, we allow simultaneous accesses to different blocks thus achieve considerable performance gain. Experiments on a virtual prototyping system show a promising result - we could achieve about 20-50% performance gain compared to the base DPSDRAM architecture.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.140-140
• /
• 2017

4륜 장착 자동차의 토크 전달은 2륜 구동, 4륜 구동 모드를 간단히 전환하는 방식(part time 4WD)과 항시 사륜 구동 모드에서 전후륜의 토크 전달비를 제어하는 방식(AWD, all wheel drive)이 있다. 경제의 발달에 따라서 취미 인구의 확대로 국내에만 180만 명의 R/C car 사용자가 있다. 이 중 2WD-4WD의 전환을 differential lock mechanism으로 구현한 수입산 모델의 가격이 1,000,000원을 호가하지만 가변 제어 방식이 아닌, 정차 후 2-4륜 구동 전환 방식을 적용하고 있으며 상대적으로 내구성이 떨어진다. DC motor의 출력이 늘어나고 배터리의 성능이 좋아진 현재 소형 RC car의 최고 속도는 80 km/h 정도로 빨라졌다. 그러나 마찰 계수가 낮은 노면(실내의 대부분 평활 처리된 복도)에서는 2륜 구동 모드의 활용도가 매우 낮다. 미끄러운 노면에서 후륜 구동 모드로는 oversteer가 발생하여 차량이 스핀하기 쉽고 전륜 구동 모드로는 understeer가 발생하여 제대로 된 코너링이 어렵다. 상시 4륜 구동 모드는 에너지 소모가 크고 전후륜이 tight coupling되어 있는 문제 때문에 일반적인 노면에서 부드러운 코너링이 잘 이루어지지 않는 문제가 있다. 본 연구에서 제안하는 방식은 그림 1와 같이 center shaft의 중간에 영구 자석으로 만들어진 토크 전달용 판이 있고 그 사이에 자계를 차폐할 수 있는 강자성체 셔터를 서보 기구에 연결하여 서보 회전각에 따라서 구동 쪽의 토크가 피구동축으로 전달되는 양을 연속 가변제어할 수 있다. 토크 전달용 판의 차폐 면적에 따른 토크 전달양을 전/후륜 바퀴의 Static torque를 통해 측정하였으며(그림 2), 공중 상태에서 즉 공기저항만을 고려한 상태에서의 RPM 회전수 차이 측정(그림3)을 통해 구동 쪽의 회전수가 피구동축으로 전달되는 양을 측정하여 연속가변 토크 제어 전달 기구의 성능을 확인하였다. 이 기구는 현재 1차적으로는 remote controller의 ch 3(ON/OFF제어 방식)에 연결하여 특정한 양의 토크를 전륜 쪽으로 보낼 수 있도록 구현이 가능하며, ch 2(PID제어 방식)에 연결하여 연속 가변 조절이 가능하도록 구현이 가능하다. 부가적으로 Arduino board를 내장하여 전후륜의 휠센서에서 입력되는 신호를 감지하여 자동적으로 전후륜에 배분되는 토크를 제어할 수 있도록 설계 중에 있다.

• Journal of the Korean Society for Library and Information Science
• /
• v.28
• /
• pp.71-81
• /
• 1995

There are no exact copies or carvings of India's original Buddhist Scripts published in Korea that had been flowed into Japan except those of WanSanJungUiMongSanPuPo(환산정의몽산법어). YaWoonJaKyung (야운자경). KyeChoShimHakInMoon(계초심학인문) PalSimSooHangChang(발심수행장) and MongsanWhaSangPupoRackLock published by a mid-Chosun Dynasty Buddhist monk, YaWoon TaesunSa. Others are the translations by Chinese people. All printings were of woodblock except ChonjimyungYangsoo- RhockChapMoon(천지명양수육잡문) of Inkyng wood printing type. This shows perhaps that the Buddhists were so devout that they spared no effort in their prayers to head for the Paradise. Even the woodblock carver himself took his hard work for granted in his belief and engraved the blocks with all his heart taking his work as God-given task. Or. perhaps they to use wood-block printing as the demand for the Scripts soared. By the way. as the Koryo Dynasty took Buddhism as the state religion, it was natural that the Buddhist Scripts were published at TaeJangToKam (the publishing office) and were much encouraged. It is noteworthy. however, that not a few Buddhist Scripts had been published during the Chosun Dynasty despite its crack-down on Buddhism as the Confucianism was declared as the state principle. The Scripts were even published by such temples as MoonJooSa(문수사), MyoHeeAm(묘희암). SsangbongSa(쌍봉사). PyoHoonSa(표훈사), YooJupSa(유점사), YongJangSa(용장사). and AnShimSa(안심사). The fact that the Scripts were even published by KanKyungToKam(간경부감) leads us to reconsider the traditional way of thinking of the Chosun Dynasty as anti-Buddhist or flunkeyist. The historical fact that a record number of Buddhist publications had been transmitted to Japan - is it accidental? - This issue could well be another subject matter for further research. However, it should be noted that very few of above­mentioned Buddhist Scripts are found in present-day Korea.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2356-2363
• /
• 2015

This study deals the optimization design with the simulation based design of a coil spring inserted into the lock nut for preventing the screw thread from loosening at the bolted joint when the high-strength steel bolt with the property class of 10.9 is used and the screw torque of 640 to 800 (Nm) is applied. In this study, structural analysis of assembly composed of bolt, nut and coil spring is carried out to evaluate its safety factors on the basis of the equivalent stress with commercial finite element analysis software. And the design strategy to extract the design improvement from these simulation results is established. An iterative process performed with the proposed design strategy is also proposed for improving the performance of the existing design. At the proposed procedure, the feasible design parameters using response surface method are found, and then these parameters are verified to be optimal or not by comparing with the response values and the simulation results obtained from the feasible parameters.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2373-2375
• /
• 2002

전자 제어식 미끄럼 방지 제동 장치(ABS, Anti-lock Brake System)를 장착한 차량의 실차 제동 시험은 시험용 차량을 비롯하여, 많은 분석장비를 필요로 한다. 이러한 고가의 장비는 구하기가 어려울 뿐만 아니라 사용방법을 학습하는 데에도 상당한 기간을 필요로 하므로, 개발중인 ABS에 대하여 적용해 보기에는 그 사용에 제약을 받는다. 본 논문에서는 개발중인 미끄럼방지 제동 알고리즘과 전자제어장치(ECU, Electronic Control Unit)를 대형 버스에 장착하여, 저 점착 노면에서 주행 시험을 시행하였고, 그 주행 기록의 분석을 위하여 DAS(Data Acquisition System)를 구현하였다. 개발 ABS 알고리즘 및 ECU의 기능과 성능 검증이 목적인 DAS는 부가적인 센서 및 고가의 장비를 사용하지 않고 제어보드와 휴대용 노트북 컴퓨터를 이용하였다. 고정밀도의 자료를 획득할 수는 없었지만, 개발 DAS를 이용한 차량 실차 제동 시험은 경제적이면서도 효과적인 ECU 및 알고리즘의 성능 분석을 이룰 수 있었다. 특히 개발 DAS는 제어 및 Data Acquisition을 동일한 보드를 사용하여 구현함으로써, ABS 장착 실차 주행 시험 결과를 제어알고리즘에 즉각적으로 반영시킨 수 있었다. 이러한 One Board System 및 On-Vehicle Programming을 이용한 방법은 개발 알고리즘의 빠른 Debugging 및 파라미터 조정(Tuning)을 가능하게 하였으므로, 실차 제동 시험을 위한 한정된 기간 내에 개발 ABS ECU 및 제어 알고리즘의 성능을 효과적으로 검증할 수 있었다.