• 소음진동
• /
• 제11권2호
• /
• pp.292-300
• /
• 2001

This research is concerned with the validation of the modeling technique and controller design for slewing beam structures. When cantilever beam rotates about axes perpendicular to the undeformed beam's longitudinal axis, it experiences inertial loading. Hence, the beam vibrates from the initial stage of slewing. In this paper, the analytical model for a single slewing flexible beam with surface bonded piezoelectric sensor and actuator is developed using the Hamilton's principle with discretization by the assumed mode method. Comparisons with the theoretical model are made based upon the frequency responses and time responses. A new factor called the coupling coefficient is introduced to incorporate the discrepancies between the theoretical and experimental results. The slewing is achieved by applying the PID control, which is found to be less sensitive to vibrations. The vibrations are controlled by PPF controller, which is found to be effective in suppressing residual vibrations after slewing. The vibrations occurred during slewing is difficult to control because the piezoceramic actuator is not powerful enough to overcome inertial loadings.

• Structural Engineering and Mechanics
• /
• 제17권3_4호
• /
• pp.445-466
• /
• 2004

In this paper, several modal identification techniques for output-only structural systems are extensively investigated. The methods considered are the power spectral method, the frequency domain decomposition method, the Ibrahim time domain method, the eigensystem realization algorithm, and the stochastic subspace identification method. Generally, the power spectral method is most widely used in practical area, however, the other methods may give better estimates particularly for the cases with closed modes and/or with large measurement noise. Example analyses were carried out on typical structural systems under three different loading cases, and the identification performances were examined throught the comparisons between the estimates by various methods.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권5호
• /
• pp.615-623
• /
• 2016

The paper describes a hysteretic buck converter including a differentiator and an adaptive hysteresis window controller. Differentiating the feedback signal achieves ultra-fast switching of the buck converter. The adaptive hysteresis window control allows a monotonous operation with predictable noise spectrum, and gives way to efficient design for variable supply and output voltages. The measurement results in a $0.13-{\mu}m$ CMOS process indicated that the switching frequency became double times higher, and the voltage ripple was reduced by up to 69%. They also indicated that the normalized switching frequency variation was reduced by 74% with variable $V_{DD}$ and by 63% with variable $V_{OUT}$. The power efficiency was improved by 3.5% depending on loading condition.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 II
• /
• pp.1145-1148
• /
• 2003

SSN을 줄이기 위해 벌크단의 그라운드와 소스단의 그라운드를 분리한다. 이 방법을 사용하면 소스과 벌크의 전압 차이가 발생하는데 소스에 발생되는 전압은 기생인덕턴스로 인해 노이즈 전압이되고 벌크의 전압은 그라운드에 바로 연결되기 때문에 0V가 된다. 이 방법을 사용하면 소스단에 기생인덕턴스가 벌크단에 미치지 못하게 되어 노이즈를 줄일 수 있다.. 본 논문에서 나타난 결과는 공통그라운드를 사용한 구동 드라이버 보다 SSN을 10% 간단히 줄일수 있다.

• 한국생산제조학회지
• /
• 제23권2호
• /
• pp.109-117
• /
• 2014

This paper reports a method to modify the gear tooth profile of a wind turbine gearbox to reduce the noise caused by the impact of the gear teeth. The major causes of tooth impact are the elastic deformation of the gear teeth, shafts, and case of the gearbox under loading, and the fabrication tolerances in gear manufacturing. In this study, the tooth profile was modified considering the elastic deformation of the gear tooth and the tooth lead modification to compensate for tooth interference in the lead direction as a result of shaft deformations. The method was applied to the gearbox of a 2.5MW wind turbine, and the transmission error was characterized before and after modifying the gear teeth. For the modified gear teeth, the transmission error (67.6%) was lower by 17.8%. Additionally, the gear contact stress was reduced by 6.3%, to 22.3%.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.722-725
• /
• 2005

Recently, ground-borne noise and vibration generated by underground transit system has been recognized as an important environmental problem. This study reviews several of the improved procedures that have been used to predict ground-borne vibration. At first, ground stiffness profile is examined by SASW test which is the most reasonable surface wave test. It is very important to acquire the exact ground stiffness profile at ground response analysis. At second, the train loading to act roadbed is calculated by using the real measured phase angle data. In finite element analysis, averaged acceleration method, infinite element, Rayleigh damping and 2-dimensional wave propagation analysis is performed.

• Smart Structures and Systems
• /
• 제21권5호
• /
• pp.637-652
• /
• 2018

This paper presents a comparative study of displacement measurement using four sensors that are being used in the field: they are a ring gauge, a laser Doppler vibrometer (LDV), a vision-based displacement measurement system (VDMS), and an optoelectronic displacement meter (ODM). The comparative study was carried out on a brand-new high-speed railroad bridge designed to produce displacements within a couple of millimeters under the loading of a high-speed train. The tests were carried out on a single-span steel plate girder bridge two times with different train loadings: KTX and HEMU. The measured displacement is compared as raw and further discussion was made on the measurement noise, peak displacement, and frequency response of four sensors. The comparisonsare summarized to show the pros and cons of the used sensors in measuring displacement at a typical high-speed railroad bridge.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.33-34
• /
• 2006

The most bottleneck of development of automation excavator system is the making mathematical linear model. Because of non-linear of control circuit, cylinder, join in hydraulic circuit, and heavy loading so on. Therefore, whatever robust controller is designed, real experimentation is necessary. But, a real experimentation has many risks. The excavator is expensive and large size. Therefore a development of experimentation system is difficult and not safe. Specially, there have a difficulty, because of big noise. So, on experimentation is difficult in school. Manufacturing pneumatic excavator modeland using system identification, design a system transfer function in this paper. Also, planning m-PID Controller using CDM, and examining usefulness applied to actuality model.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 연구회
• /
• pp.33-37
• /
• 2001

Recently, the HFPD measurement testing is widely used in partial discharge measurement of HV machines because HFPD measurement testing receives less influence of external noise and has a merit of good sensitivity. Also HFPD testing is able to offer the judgement standard of degradation level of HV machine and can detect discharge signals in live-line. Therefore it is very useful method compare to previous conventional PD testing method and effective diagnosis method in power transformer that requires live-line diagnosis. But partial discharges have very complex characteristics of discharge pattern so it is required continuous research to development of precise analysis method. In recent, the study of partial discharge is carrying out discover of initial defect of power equipment through condition diagnosis and system development of degradation diagnosis using HFPD(High Frequency Partial Discharge) detection. In this study, simulated transformer is manufactured and HFPD occurred from transformer is measured with broad band antenna in real time, the degradation grade of transformer is analyzed through produced patterns in simulated transformer according to applied voltages.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.89-93
• /
• 2004

To numerically construct the sound fields by a plenum fan mostly found in Air-Handling Unit (AHU), the Kirchhoff-BEM approach was applied to the near-field data of a turbo fan. The scattering effects were found to be significant by the plenum box structure for high-frequency components of source. The directivity petterns and sound pressure levels were also dependent upon the helmholts number which must be considered of the design stage for sound reduction program.