• Journal of Mechanical Science and Technology
• /
• v.14 no.4
• /
• pp.418-425
• /
• 2000

Recently, many passenger cars have adopted automatic transmissions for shifting gears, and thus the smooth and precise control of gear shifts of passenger car automatic transmissions has become more and more essential for the riding comfort of vehicles equipped with automatic transmissions. In this article, a neural network-based supervisor for an automotive shift controller considering the throttle opening, variations in throttle opening, and the driving load is presented. For using the driving load information, an observer-based driving load estimation algorithm is proposed. A proportional-integral-derivative controller along with an open loop controller is used as a low level controller for controlling the gear shifts, and a supervisory controller for properly adapting the shift control parameters of the low level shift controller is designed using ANFIS. To evaluate the control performance of the proposed supervisor-based shift controller, both simulation studies and experimental studies are performed for various shifting situations.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2002.05a
• /
• pp.256-259
• /
• 2002

Recently, most vehicles has the Automatic transmission system as their transmission system. The automatic transmission system operates with fixed shift patterns. In the opposite of manual operation, it is easy and convenient for driving. Though these merit, the system can not evaluate the driver's intension because of usage of firmed shift pattern. Especially, when the load has declination the AT system must operate for engine break effect. Namely, if the vehicle drives on the load of decrease, the acceleration of the vehicle goes to high then. At that time, the shift goes to down position the vehicle has some negative acceleration with the resistance of engine. To consider driver's intension in this case, we must consider both the driving intensity of driver and the status of load. In this paper, we developed flexible automatic transmission system by using the proposed moduled neural networks which can learn the status of the load and driver's intensity As a result, we compare the transmission system using firmed shift pattern and the proposed transmission system and show the good performance in the change of shift position.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.9
• /
• pp.869-874
• /
• 2015

We developed an LSDC (Load Shift and Load Distribution Control) technology in order to improve coil quality and productivity by reducing tension fluctuation especially for the tail of the strip in the down coiler in hot strip mills. To adapt the new controller, the torque and speed distribution between the zero pinch roll, pinch roll, and mandrel are needed. The proposed controller is a combination of an LSC to share the tension between the mill stand and the mandrel, and an LDC to shift the torque load from the zero pinch roll to the pinch roll. From the simulation, the proposed controller is verified under the torque disturbance. Using a field test, the torque deviation decreased by nearly 50% through utilization of the LSDC control.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.168-174
• /
• 2004

A shift algorithm of an automatic transmission is decided by the compromise between the performance and the fuel economy of the vehicle. But because in the traditional shia algorithm, throttle opening and vehicle speed are used to decide the shift points, the actual load of the vehicle is not exactly considered. In this paper, to consider the actual load, that is, the road grade and the vehicle acceleration, the longitudinal accelerometer is used to decide the shift points. As the result, the performance and the fuel economy of the vehicle which adapts the new shift algorithm are shown better than the traditional one.

• Journal of Power Electronics
• /
• v.15 no.5
• /
• pp.1392-1401
• /
• 2015

Inverter configurations for multiple-load induction cooking applications need development. Inverter configurations for induction cooking applications are used in home appliances based on single coil inverters. For multiple-load configurations, multiple coils are used. They require proper inverters, which provide independent control for each load and have fewer components. This paper presents a three-leg inverter configuration for three load induction cooking applications. Each induction coil powers one induction cooking load. This configuration operates with constant switching frequency and powers individual loads. The output power of the required load is controlled with a phase-shift control technique. This configuration is simulated and experimentally tested with three induction loads. The simulation and experimental results are in good agreement. This configuration can be extended to more loads.

• Steel and Composite Structures
• /
• v.5 no.2_3
• /
• pp.235-246
• /
• 2005

Local buckling is a major consideration in the design of thin-walled cold-formed steel sections. The main effect of local buckling in plate elements under longitudinal compressive stresses is to cause a redistribution of the stresses in which the greatest portion of the load is carried near the supporting edges of the plate junctions. The redistribution produces increased stresses near the plate junctions and high bending stresses as a result of plate flexure, leading to ultimate loads below the squash load of the section. In singly symmetric cross-sections, the redistribution of longitudinal stress caused by local buckling also produces a shift of the line of action of internal force (shift of effective centroid). The fundamentally different effects of local buckling on the behaviour of pin-ended and fixed-ended singly symmetric columns lead to inconsistencies in traditional design approaches. The paper describes local buckling and shift of effective centroid of thin-walled cold-formed steel channel columns. Tests of channel columns have been described. The experimental local buckling loads were compared with the theoretical local buckling loads obtained using an elastic finite strip buckling analysis. The shift of the effective centroid was also compared with the shift predicted using the Australian/New Zealand and American specifications for cold-formed steel structures.

• Journal of ILASS-Korea
• /
• v.19 no.2
• /
• pp.64-68
• /
• 2014

A driving vehicle performance which is driven by FTP-75 mode was simulated by computer. Throttle valve position, engine speed, air mass flow rate, fuel consumption et al. were computer simulated. A set of engine part load performance data, automatic transmission shift map and vehicle specifications were used for the computer simulation. Throttle valve position, engine speed, air mass flow rate et al. measured for evaluating the computer simulation results by driving the vehicle with FTP-75 mode on a chassis dynamometer. GT-Power$^{(R)}$ software was used for the computer simulation of the driving vehicle performance. Experimental fuel consumption rate was measured by using an ECU HILS fuel injection system. The experimental data and simulation results were compared. The computer simulation of the driving vehicle performance predicts the measured data well comparatively.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.4
• /
• pp.517-525
• /
• 1996

A Simple AC complex circuit analysis for LCL type series resonant converter with phase shift control is proposed. Based on these analyses, a set of characteristic curves which allows a optimal design procedure for this converter is shown, without increasing the volt-ampere rating of tank circuit Especially, inverter output peak current can be minimized in both full load and partial load conditions. The presented design considerations can make the load range wide from full loads to light loads achieving turn-on with zero voltage switching (ZVS) operation. The detailed analysis and experimental results show the effectiveness of the proposed design algorithms. (author). refs., figs., tab.

• Journal of Mechanical Science and Technology
• /
• v.16 no.5
• /
• pp.639-646
• /
• 2002

In this paper, thrust equations for a rubber belt CVT are derived by considering the geometry and mechanism of the mechanical actuators. In order to solve the thrust equations, an algorithm to calculate the speed ratio is suggested for the given driver speed and load torque based on the actuator characteristic equations and existing formula for the belt thrust forces. Experiments are performed to investigate the driver speed-load torque-speed ratio characteristics at a steady state. The speed and torque efficiencies are measured and used to modify the actuator equations. It is found that the modified equations well predict the steady state characteristics. In addition, the shift dynamic model for a rubber belt CVT is derived experimentally. Simulation results of the CVT shift dynamics are in good accordance with the experiments and it is noted that different coefficients are required to describe the CVT shift dynamics for the upshift and the downshift.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.654-664
• /
• 2017

This paper proposed an unified dual-phase-shift (UDPS) control for dual active bridge (DAB) converters in order to improve efficiency for a wide output power range. Different operating modes of UDPS are characterized with respect to the reactive current distribution. The proposed UDPS has the same output power capability with conventional phase-shift (CPS) method. Furthermore, its implementation is simple since only the change of the leading phase-shift direction is required for different operating power range. The proposed UDPS control can minimize both the inductor rms current and the circulating reactive current for various voltage conversion ratios and load conditions. The optimal phase-shift pairs for two bridges of DAB converter are derived with respect to the comprehensive reactive power loss model, including the reactive components delivered from the load and back to the source. Simulation and experimental results are illustrated and explained with details. The effectiveness of the proposed method is verified in terms of reactive power losses minimization and efficiency improvement.