• Journal of Electrical Engineering and Technology
• /
• 제13권3호
• /
• pp.1251-1264
• /
• 2018

The systematic and effective design method of a Class-D current-source resonant inverter for use in an induction cooker with zero-ripple line current is presented. The design procedure is based on the principle of the Class-D current-source resonant inverter with a simplified load network model that is a parallel equivalent circuit. An induction load characterization is obtained from a large-signal excitation test-bench based on parallel load network, which is the key to an accurate design for the induction cooker system. Accordingly, the proposed scheme provides a systematic, precise, and feasible solution than the existing design method based on series-parallel load network under low-signal excitation. Moreover, a zero-ripple condition of utility-line input current is naturally preserved without any extra circuit or control. Meanwhile, a differential-mode input electromagnetic interference (EMI) filter can be eliminated, high power quality in utility-line can be obtained, and a standard-recovery diode of bridge-rectifier can be employed. The step-by-step design procedure explained with design example. The devices stress and power loss analysis of induction cooker with a parallel load network under large-signal excitation are described. A 2,500-W laboratory prototype was developed for $220-V_{rms}/50-Hz$ utility-line to verify the theoretical analysis. An efficiency of the prototype is 96% at full load.

• 조명전기설비학회논문지
• /
• 제14권6호
• /
• pp.12-17
• /
• 2000

IN induction heating system the high frequency operation allows a rapid response to current fluctuation in the inverter and result in improved welding quality. To work induction heating of nonferrous metals, a welding power supply is need high working frequency and high power. This paper is shown design technique for increasing working frequency in induction heating for welding coppers. A series-parallel resonate inverter consists of H-type bridges, each of whose arms is composed of a combination of two parallel IGBTs. Inverter operating with the fixed frequency is controlled by pulse width modulation (PWM). As switching adapted the Zero-Voltage Switching technique to reduce switching losses the system is high efficiency. The propose inverter has feature which is high efficiency for very wide load variations with a narrow range of duty cycle ratio control and load short circuit capability. Detailed experimental results obtained from a 48[V] output, 500[W] experimental inverter are presented to verify the concept.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2002년도 학술대회논문집
• /
• pp.293-296
• /
• 2002

This paper describes the instantaneous current resultant type load parallel high frequency resonant inverter consisting of three unit half-bridge serial and parallel resonant inverter can be used as power source of induction heating. This proposed inverter can reduce distribution of the switching current because of using the current of serial resonant circuit to the input current of the parallel one. The analysis of the proposed circuit is generally described by using the normalized parameters. Also, the principle of basic operating and the its characteristics are estimated by the parameters such as switching frequency($\mu$), load resistance(λ). Experimental results are presented to verify theoretical discussion. This proposed inverter will can be practically used as a power supply in various fields as induction heating application, DC-DC converter etc.

• Journal of Electrical Engineering and Technology
• /
• 제9권4호
• /
• pp.1137-1144
• /
• 2014

A parallel-feeding AC traction power system increases the power supply capacity and decreases voltage fluctuations, but the circulating power flow caused by the phase difference between the traction substations prevents the system from being widely used. A circuit analysis shows that the circulating power flow increases almost linearly as the phase difference increases, which adds extra load to the system and results in increased power dissipation and load unbalance. In this paper, we suggest a phase shifter for the parallel-feeding AC traction power system. The phase shifter regulates the phase difference and the circulating power flow by injecting quadrature voltage which can be obtained directly from the Scott-connection transformer in the traction substation. A case study involving the phase shifter applied to the traction power system of a Korean high-speed rail system shows that a three-level phase shifter can prevent circulating power flow while the phase difference between substations increases up to 12 degrees, mitigate the load unbalance, and reduce power dissipation.

• 한국컴퓨터산업학회논문지
• /
• 제9권2호
• /
• pp.63-68
• /
• 2008

병렬 스케줄링의 목적은 다중프로세서 병렬시스템 환경에서 병렬성을 가진 응용 프로그램에 대하여 최소 동기화 오버헤드(Synchronization overhead) 및 병목현상(Bottleneck) 그리고 부하균등(Load balance)을 달성하도록 스케줄링을 수행하는데 있다. 본 논문에서는 기존의 대표적인 병렬수행 스케줄링 알고리즘들을 분석하고 각 방법들로부터 문제점들을 도출한다. 이는 향후 효율적인 알고리즘을 설계하는데 도움이 필 것이다.

• Journal of Power Electronics
• /
• 제19권5호
• /
• pp.1153-1161
• /
• 2019

A current sharing controller is proposed in this paper for parallel-connected converters. The proposed controller is based on the calculation of the magnitudes of system current space vectors. Good current distribution between parallel converters is achieved with only one Proportional-Integral (PI) compensator. The proposed controller is analyzed and the circulating current impedance is derived for paralleled systems. The performance of the new control strategy is experimentally verified using two parallel connected converters employing Space Vector Pulse Width Modulation (SVPWM) feeding a passive RL load and a 2.2 kW three-phase induction motor load. The obtained test results show a reduction in the current imbalance ratio between the converters in the experimental setup from 53.9% to only 0.2% with the induction motor load.

• 조명전기설비학회논문지
• /
• 제27권4호
• /
• pp.88-95
• /
• 2013

A new droop control method which can be applied to 3-phase 4-wire uninterruptible power supply is proposed in this paper. The droop control method for parallel operation is very attractive one as UPS parallel operation can be carried out without any data communication devices provided among UPS systems connected, but it reportedly shows a PnP(plug-and-play) problem. A basic reason why a circulating current could flow among parallel-connected UPS systems is clearly investigated as well when droop-controlled-ups systems are operated in the manner of PnP. The proposed algorithm is deduced from the investigated result and is basically structured to keep a balanced frequency and balanced voltage profile against power variation. This paper shows that balanced parallel operation of droop control method can be obtained under unbalanced load as well as balanced load conditions when PnP operation is needed and load change occurs.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 ITC-CSCC -1
• /
• pp.314-317
• /
• 2000

Cluster system provides attractive scalability in terms of computation power and memory size. With the advances in high speed computer network technology, cluster systems are becoming increasingly competitive compared to expensive parallel machines. In parallel processing program, each task load is difficult to predict before running the program and each task is interdependent each other in many ways. Load imbalancing induces an obstacle to system performance. Most of researches in load balancing were concerned with distributed system but researches in cluster system are few. In cluster system, the dynamic load balancing algorithm which evaluates each processor's load in runtime is purpose that the load of each node are evenly distributed. But, if communication cost or node complexity becomes high, it is not effective method for all nodes to attend load balancing process. In that circumstances, it is good to reduce the number of node which attend to load balancing process. We have modeled cluster systems and proposed marginal dynamic load balancing algorithms suitable for that circumstances.

• Journal of Power Electronics
• /
• 제5권2호
• /
• pp.160-165
• /
• 2005

In a parallel operation of UPS, there are two types of circulating currents between UPS. One is the low order circulating current with a fundamental frequency caused by the amplitude and phase differences of UPS output voltages, and the other is the harmonic circulating current with PWM switching frequency caused by non-synchronized PWM waveforms among UPS. The elimination of the low order circulating current is essential for optimal load sharing in parallel operations of UPS, which can be accomplished by the phase and magnitude control at each UPS. The harmonic circulating current may cause troubles and deteriorate in performance of the controller for optimal load sharing in parallel operation of UPS. This paper presents a PWM synchronizing method to eliminate the harmonic circulation current in parallel operation of UPS. The effectiveness of the proposed scheme has been investigated and verified through experiments by a 50kVA UPS.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.90-94
• /
• 1998

The parallel inverter is popularly used because of its fault-tolerance capability, high-current outputs at constant voltages and system modularity. The conventional parallel inverter usually employes active and reactive power control or frequency and voltage droop control. However, these approaches have the disadvantages that the response time of parallel inverter control is slow against load and system parameter variation to calculate active, reactive power, frequency and voltage. This paper describes a novel control scheme for power equalization in parallel connected inverter. The proposed scheme has a fast power balance control response, a simplicity of implementation, and inherent peak current limiting capability since it employes a instantaneous current/voltage control with output voltage and current balance and output voltage regulation. A design procedure for the proposed parallel inverter controller is presented. Futhermore, the proposed control scheme is verified through the simulation in various cases such as the system parameter variation, the control parameter variation and the nonlinear load condition.