• Journal of Korea Foundry Society
• /
• v.37 no.6
• /
• pp.207-216
• /
• 2017

This study investigated the effects of the addition of Zn, Ca, and SiC on the microstructure and mechanical properties of Mg-Al alloys. The tensile properties of homogenized Mg-xAl (x = 6, 7, 8, and 9 wt.%) alloys increased with increasing Zn content by the solid-solution strengthening effect. However, when the added Zn content exceeded the solubility limit, the strength and ductility of the alloys decreased greatly owing to premature fracture caused by undissolved coarse particles or local melting. Among the Mg-xAl-yZn alloys tested in this study, the AZ74 alloy showed the best tensile properties. However, from the viewpoints of the thermal stability, castability, and tensile properties, the AZ92 alloy was deemed to be the most suitable cast alloy. Moreover, the addition of a small amount (0.17 wt.%) of SiC reduced the average grain size of the AZ91 alloy significantly, from $430{\mu}m$ to $73{\mu}m$. As a result, both the strength and the elongation of the AZ91 alloy increased considerably by the grain-boundary hardening effect and the suppression of twinning behavior, respectively. On the other hand, the addition of Ca (0.5-1.5 wt.%) and a combined addition of Ca (0.5-1.5 wt.%) and SiC (0.17 wt.%) increased the average grain size of the AZ91 alloy, which resulted in a decrease in its tensile properties. The SiC-added AZ92 alloy exhibited excellent tensile properties (YS 125 MPa, UTS 282 MPa, and EL 12.3%), which were much higher than those of commercial AZ91 alloy (YS 93 MPa, UTS 192 MPa, and EL 7.0%). The fluidity of the SiC-added AZ92 alloy was slightly lower than that of the AZ91 alloy because of the expansion of the solid-liquid coexistence region in the former. However, the SiC-added AZ92 alloy showed better hot-tearing resistance than the AZ91 alloy owing to its refined grain structure.

• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.57-67
• /
• 2002

The effect of $\beta$-TCP and PHA as additives on initial setting time, compressive strength and surface micro-structure after in vitro test of bone cement in TTCP and DCPA system was investigated. The median particle sizes of TTCP, $\beta$-TCP, DCPA and PHA for bone cement were about 3, 5, 0.9 and 4${\mu}{\textrm}{m}$, respectively. Initial setting time and compressive strength of bone cement with various composition was measured by Vicat test and Universal Testing Machine, and surface morphology and crystalline phases of bone cements were observed and analyzed by SEM and x-ray diffractometer. Initial setting time was not affected by composition but by powder/liquid ratio, and cement with PHA required double amount of solution for paste as much as one without PHA, especially. It was thought that $\beta$-TCP and PHA in bone cements was not related to setting reaction. Thus, the addition of $\beta$-TCP and PHA in bone cements decreased compressive strength and inhabited HAP from being produced on surface in vitro test. In conclusion, it was not expected that $\beta$-TCP and PHA in TTCP-DCPD bone cements enhanced the strength and bioacitivity.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.51 no.spc1
• /
• pp.166-173
• /
• 2006

Soyasaponins are phytochemicals of major interest fur their health benefits. Chemical investigation of a soybean phytochemical concentrate resulted in the isolation and identification of triterpenoid saponins. The MeOH extraction of defatted hypocotyl separated from soybeans was peformed by the automated solvent extractor (ASE). Fractionation was performed on a flash column ($150mm{\times}40mm$ i.d.) packed with a preparative $C_{18}$ reverse phase bulk packing material $(125\AA,\;55-105{\mu}m)$ and monitored at 210 nm, and collected 14 fractions. Consequent Fsat preparative column liquid chromatography (Fast PCLC) was performed for the purification of Fraction-I (Fr-I) collected from the fraction 8 and 9 of flash chromatography. Fsat PCLC was performed on a Luna $C_{18}\;10{\mu}m,\;100{\AA}$, semipreparative reverse phase column ($250cm{\times}50mm$ i.d.) for the purification of isolated unknown compound (Fr-I-2). Chemical structure of acetyl soyasaponin $A_1\;(MW:1436.6,\;C_{67}H_{104}O_{33})$ was identified and determined by a combination of extensive NMR ($^1H-NMR$, 400 MHz; $^{13}C-NMR$, 100 MHz; DEPT), IR, UV, and ESI-MS analysis.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.4
• /
• pp.314-321
• /
• 2000

A gap between a $Al_2O_3/Fe$ thermite and lower head vessel is formed in the lower-plenum arrested vessel attack(LAVA) experiment which is the 1st phase study of simulation of naturally arrested vessel attack in vessel(SONATA-IV). The gap measurement using a conventional ultrasonic method would be lack of a reliability due to the structure complexity and the metallurgical grain size change of the lower head HAZ occurred by a thermite $Al_2O_3/Fe$ melt or a $Al_2O_3$ melt at $2300^{\circ}C$. The grain echoes having false signals and lower S/N ratio signals are detected due to a multiple scattering, a mode conversion and an attenuation of a ultrasonic resulted from at the interface of increased grain size zone. In this test, the signals pattern was classified to understand the behavior of the ultrasonic in a multi-layer specimen of solid-liquid-solid of assuming that the thermite and the lower head vessel is immersed. The polarity threshold algorithm of frequency diversity gives us the enhancement about 6dB of the ratio S/N.

• Proceedings of the Technology Innovation Conference
• /
• 1997.12a
• /
• pp.159-176
• /
• 1997

This paper deals with demand surveys for big science and technology research facilities and equipments to advance national S'||'&'||'T research infrastructure. We perform surveys thrice based on applied Delphi method on the future demand of big S'||'&'||'T research facilities and equipments among Korean scientists and engineers. We employ the concept of big S'||'&'||'T research facilities and equipments as follows: \circled1 The operating size of it is equivalent to that of an institute or research center, and/or \circled2 The users in various disciplines are many, and/or \circled3 The application areas or spill-over effects are large, and/or \circled4 The scale and scope of research objects is equivalent to that of mega science area such as earth.oceanography.space, and/or \circled5 The expenses for installing and operating it are to be supported by government, and/or \circled5 The facilities are expected as necessary for international joint research, and/or \circled7 It is necessary for promoting creative basic science and developing creative technology. We ask the respondents to answer the following questionnaire: - How to prioritize the equipments according to the degree of importance\ulcorner $\square$ Promotion of basic science and mega science, the development of the technologies to enhance the public welfare, the competitiveness of industrial technologies, the job creation for the S'||'&'||'T personnel, and international cooperation. - Who should be in charge of acquisition and operation of the equipments\ulcorner $\square$ Industry, Government Research Institutes, Academy, ERC and SRC. - When shall we acquire the equipment\ulcorner $\square$ Within 2000, 2002, 2007, 2012, and 2017. - How shall we acquire the equipments\ulcorner $\square$ International Joint Development, Domestic Development, Acquisition from Overseas, - How much will the equipment generate spill-over effects to national competitiveness\ulcorner $\square$ Promotion of basic science, contribution to the economy, supply of S'||'&'||'T personnel, and international cooperation. We suggest the following equipments as prioritized candidates after consulting the officers from MOST, MOE, MIC, MOEN and experts from KBSI and STEPI:(table omitted) where, #1, Korea Advanced Liquid Metal Reactor, #2. 800 MHz Superconduction Fourier-Transform Nuclear Magnetic Resonance Spectrometer, #3. Ion Accelerator, #4. Seismic Test Facility, #5. Transonic Wind Tunnel, #6. Radio Telescope for Very Long Baseline Interferometer, #7. 3000t Universal(or Large Structure) Testing Machine, #8. Compost Facility or Plasma Pyrolysis Facility.

• Applied Biological Chemistry
• /
• v.46 no.1
• /
• pp.60-65
• /
• 2003

MMP-1 inhibitory compounds were isolated from 120 Korean traditional edible plants. UP- 1 activity significantly increased linearly with increasing UVB dose in normal human foreskin fibroblast HS68 cell, showing maximum activity at approximately 35 $mJ/cm^2$, whereas in HaCaT cell, normal human keratinocyte, no increase was observed. Maximum secretion of MMP-1 after UVB treatment occurred around 36-48 k after treatment. MMP-1 inhibitory compound isolated from cold-water fraction of Cataegus pinnatifida Bunge showed the mort potent activity. The MMP-1 inhibitory compound was deduced as a peptide based on the fact that pronase digestion decreased the activity whereas periodate oxidation did not. The most potent UP- 1-inhibitory protein, CP-2Va-2, showing an activity of 88.5% against MMP-1, was isolated through sequential column chromatography on DEAE-Toyopearl 650C, Butyl-Toyopearl 650M, and Bio-Gel P-30. Molecular weight of CP-2Va-2 determined through high performance liquid chromatography and SDS PACE was 19 and 20 kDa. respectively, signifying a monomeric structure.

• International Journal of Automotive Technology
• /
• v.5 no.4
• /
• pp.221-238
• /
• 2004

Wall interactions of direct injection spray were investigated using laser-sheet imaging, shadowgraphy, wetted footprint and phase Doppler interferometry techniques. A narrow-cone high-pressure swirl injector is used to inject iso-octane fuel onto a plate, which has three different impact angles inside a pressurized chamber. Heated air and plate conditions were compared with unheated cases. Injection interval was also varied in the heated case to compare dry- and wet- wall impingement behaviors. High-speed macroscopic Mie-scattering images showed that presence of wall and air temperature has only minor effect on the bulk spray structure and penetration speed for the narrow-cone injector tested. The overall bulk motions of the spray plume and its spatial position at a given time are basically unaffected until a few millimeters before impacting the wall. The surface properties of the impact surface, such as the temperature, the presence of a preexisting liquid film also have a small effect on the amount of wetting or the wetted footprint; however, they have strong influence on what occurs just after impact or after a film is formed. The shadowgraph in particular shows that the plate temperature has a significant effect on vapor phase propagation. Generally, 10-20% faster horizontal vapor phase propagation is observed along the wall at elevated temperature condition. For impingement onto a preexisting film, more splash and evaporation were also observed. Contrary to some preconceptions, there is no significant splashing and droplet rebounding from surfaces that are interposed in the path of the DI gasoline spray, especially for the oblique impact angle cases. There also appears to be a dense spray front consists of large sac spray droplets in the oblique impact angle cases. The bulk of the spray is not impacted on the surface, but rather is deflected by it The microscopic details as depicted by phase Doppler measurements show that the outcome of the droplet impaction events can be significantly influenced. Only droplets at the spray front have high enough Weber numbers for wall impact to wet, splash or rebound. Using the sign of vertical velocity, the time-resolved downward droplets and upward droplets are compared. The Weber number of upward moving droplets, which seldom exceeds unity, also decreases as the impact angle decreases, as the droplets tend to impact less and move along the wall in the deflected spray plume.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.1
• /
• pp.79-92
• /
• 2011

In this study, wave pressure of short-period gravity waves and tsunami acting on the upright section of the horizontal-slit type caisson placed on the impermeable or permeable seabed, which is a well-known permeable breakwater with a good wave controlling ability, are investigated via numerical simulations. Further, the permeable seabed was modeled as the porous media with porosity of 0.4. Using the numerical results, the effects of the seabed conditions on the wave pressure on the front wall and inside wall of the chamber have been studied. In the numerical simulations, short-period gravity waves and tsunami(solitary wave or bore) with the same amplitude to the gravity wave are considered. A numerical wave tank is used, which is able to consider a gas-liquid two-phase flow in the same calculation zone. Numerical results show that the wave pressure of the tsunami was 3~5 times higher than the short-period gravity waves acting on the front wall and it was 2~4 times higher than the short-period gravity waves acting on the inner wall.

• Journal of the Mineralogical Society of Korea
• /
• v.18 no.4 s.46
• /
• pp.313-323
• /
• 2005

XRD, XRF, EPMA, FT-IR, and SEM-CL studies were carried out in order to characterize gemological features of corundum from Tanzania. Fluorescence reaction of the Tanzanian corundum to short and long wave ultraviolet rays was weakly detected. Inclusions in Tanzanian corundum are divided into five types, Type I is fluid-rich inclusion, Type II is gas-rich inclusion, Type III is liquid $CO_{2}$ inclusion, Type IV is solid-rich inclusion, and Type V is a mixture of fluid and solid inclusion and daughter minerals. SEM-CL images show twin structure with growth texture, microphenocryst of spinel solid inclusions, massive and growth texture. Ruby and sapphire from Tanzania are distinctly distinguished by concentrations of Fe and Cr, and plotted in the particular field at $Al_{2}O_{3}/100-Cr_{2}O_{3}-Fe_{2}O_{3}$ diagram. According to FT-IR analysis, all corundum specimens from Tanzania showed the similar patterns, and absorption peaks of $455.09\~459.23\;cm^{-1},\;603.15\~611.71\;cm^{-1},\;1509.00\~1655.05\;cm^{-1}\;and\;3436.41\~3468.87\;cm^{-1}$. These distinctive characteristics mentioned above can be used to identify the locality and source of corundum stones from Tanzania.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.11
• /
• pp.1005-1013
• /
• 2010

This study was conducted to assess the spray control of flash boiling with mixed fuel in consideration of HCCI (Homogeneous Charge Compression Ignition) engine condition. Mixed fuel existing in two phase regions can control the process of mixture formation under low temperature and density by using the spray resulting from flash boiling which is able to induce rapid evaporation of fuel spray as well as the evaporation of high boiling point component. Because HCCI engine injects the fuel early under ambient conditions, it can facilitate the chemical control of ignition combustion and physical control such as breakup and atomization of liquid fuel by flash boiling of mixed fuel which consists of highly ignitable light oil and highly volatile gasoline. This study was conducted by performing video processing after selected composition and molar fraction of the mixed fuel as major parameters and photographed Schlieren image and Mie scattered light corresponding to the flash boiling phenomenon of the fuel spray that was injected inside a constant volume vessel. It was found that flash boiling causes significant changes in the spray structure under relatively low temperature and density. Thus, we analyzed that the flash boiling spray can be used for HCCI combustion by controlling the mixture formation at the early fuel injection timing.