• Journal of Electrochemical Science and Technology
• /
• v.10 no.3
• /
• pp.294-301
• /
• 2019

The quasi-solid-state hybrid electrolytes were synthesized by chemical cross-linking reaction of methacrylate-functionalized $SiO_2$ ($MA-SiO_2$) and tetra (ethylene glycol) diacrylate in aqueous electrolyte. A quasi-solid-state electrolyte synthesized by 6 wt.% $MA-SiO_2$ exhibited a high ionic conductivity of $177mS\;cm^{-1}$ at room temperature. The electrochemical $H_2$ sensor assembled with quasi-solid-state electrolyte showed relatively fast response and high sensitivity for hydrogen gas at ambient temperature, and exhibited better durability and stability than the liquid electrolyte-based sensor. The simple construction of the sensor and its sensing characteristics make the quasi-solid-state hydrogen sensor promising for practical application.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2321-2326
• /
• 2007

To return LNG to a gaseous state, it is fed into a regasification plant. For inland area, where pipelines do not exist or difficult to construct, the LNG is delivered to the inland-receiving terminal available at that area, regasified and delivered to consumers. At inland-receiving terminal, air-heating vaporizer type is usually used. To contribute in developing an efficient air-heating vaporizer, experiment on finned type air-heating vaporizer using 8 fins, 50 mm fin length (8fin50le) and 4 fins, 75 mm fin length (4fin75le) were conducted. The experiments were conducted by varying the ambient condition and the length of the vaporizer. The ambient air was controlled so that it has the same condition with air condition in every season available. $LN_2$ is used to substitute LNG because of safety reason. The results show that characteristics of the finned type 4fin75le vaporizer are comparable to finned type 8fin50le vaporizer at all season.

• Journal of Environmental Health Sciences
• /
• v.34 no.1
• /
• pp.42-48
• /
• 2008

The objectives of this study were to measure ambient TGM concentrations in Seoul Korea, to determine the temporal variation of TGM, and to analyze the relationships among TGM, meteorological data and PM2.5 measured at the same time. Ambient TGM and PM2.5 concentrations were measured at the roof of the Graduate School of Public Health building in Seoul, Korea for the period of January to October 2004. Average TGM concentration was $3.43{\pm}1.17ng/m^3$. The average TGM was at a low concentration similar to those of background sites in other countries. The temporal variations and meteorological phenomena of TGM were not statistically significant. There was a positive link between TGM and PM2.5. It didn't indicate that reduction of $Hg^{2+}$ to Hg0 had occurred in liquid water contained in smog as in a previous study, but it shows that PM2.5 and TGM could be emitted from the same sources such as power plants and combustion engines. Also, the strong correlation between TGM and $SO_2$ concentrations indicated that the source of TGM was from fossil fuel combustions including coal combustion. Specifically, $SO_2\;and\;SO_4{^2-}$ concentrations correlated to TGM concentrations could be linked to TGM emitted from local and regional sources as well.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.42-52
• /
• 1997

The basic principle of underwater ram-jet as a unique marine propulsion concept showing vary high cruise speed range(e. g. 80-100 knots) is the thrust production by the transfer of the potential energy of compressed gas to the operating liquid through kinetic mixing process. This paper is aimed to investigate the propulsive efficiency of the nozzle flow in underwater ram-jet at the speed of 80 knots for the buried type vessel. The basic assumption of the theoretical analysis is that mixture of water and air can be treated as incompressible gas. For an optimized nozzle configuration obtained from the performance analysis, preliminary data for performance evaluation are obtained and effects of nozzle inner wall friction, ambient temperature, ambient pressure, water density, gas velocity, bubble radius, flow velocity, diffuser area ratio, mass flow ratio and water velocity gradient are investigated.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.11
• /
• pp.1105-1114
• /
• 2010

Ice shapes accumulated on the aircraft surfaces are categorized into rime and glaze ice, which are highly dependent on various parameters such as ambient temperature, liquid water contents (LWC), mean volumetric droplet diameter and freestream velocity. In this study, quantitative analyses on the ice accretion have been attempted in a systematical manner and the key findings are as follows. First, the increase of freestream velocity can cause tremendous change in the ice accumulation such as the growth of ice accretion area, ice heading direction and maximum thickness of ice horn. Second, LWC is found to be linearly proportional to the ice accretion area. Third, the effects of ambient temperature on incoming water mass seem to be relatively small in comparison with LWC and freestream velocity. Finally, it was shown that MVD has only a little influence on ice shapes. However, it may increase the ice accretion area by increasing the droplet impacting range.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.4
• /
• pp.616-624
• /
• 2018

In this study, a previous DNPH (2,4-dinitrophenylhydrazine) coupled with high performance liquid chromatography (HPLC) method to measure the concentration of formaldehyde in ambient and source environments has been improved. To improve the disadvantage of the previous HPLC method, an appropriate composition ratio of mobile phase (water: acetonitrile (ACN)) was determined and an isocratic analysis was conducted. Furthermore, limit of detection (LOD), limit of quantitation(LOQ), accuracy, and precision were investigated to verify the reliability of the analytical conditions determined. Finally, samples of exhaust gases from five different industrial facilities were applied to HPLC analytial method proposed to determine their formaldehyde concentrations. The appropriate composition ratio of the mobile phase under the isocratic condition was a mixture of water(40%) and ACN(60%). As the volume fraction of the organic solvent ACN increases, retention time of the formaldehyde peak was reduced. Detection time of formaldehyde peak determined using the proposed isocratic method was reduced from 7 minutes(previous HPLC method) to approximately 3 minutes. LOD, LOQ, accuracy, and precision of the formaldehyde determined using standard solutions were 0.787 ppm, 2.507 ppm, 93.1%, and 0.33%, respectively, all of which are within their recommended ranges. Average concentrations of the formaldehyde in five exhaust gases ranged from 0.054 ppm to 1.159 ppm. The lowest concentration (0.054 ppm) was found at samples from waste gas incinerator in a bisphenol-A manufacturing plant. The highest was observed at samples from the absorption process in manufacturing facilities of chemicals including formaldehyde and hexamine. The analytical time of the formaldehyde in ambient air can be shortened by using the isocratic analytical method under appropriate mobile phase conditions.

• Journal of ILASS-Korea
• /
• v.17 no.3
• /
• pp.113-120
• /
• 2012

It is being more serious problems that the pollutant and the greenhouse gas emitted from the internal combustion engines due to the increasing demand of automobiles. To counteract this, as one of the ways has been studied, GDI type engine, which is directly injected into the combustion chamber and burns by a spark ignition that chose the merits of both gasoline engine and diesel engine, was appeared. The combustion phenomena in this GDI engine is known to contribute to combustion stability, fuel consumption reduction and reductions of harmful substances of exhaust gas emission, when the fuel spray of atomization being favorable and the mixture formation being promoted. Accordingly, this study analyzed the affection of ambient temperature and fuel injection pressure to the fuel by investigate the visualization of combustion, combustion pressure and the characteristic of emission, by applying GDI system on the constant combustion chamber. As a result, as the fuel injection pressure increases, the fuel distribution in the combustion chamber becomes uniform due to the increase of penetration and atomization. And when ambient temperatures in the combustion chamber become increase, the fuel evaporation rate being high but the penetration was reduced due to the reduction of volume flux, and confirmed that the optimized fuel injection strategy is highly needed.

• Journal of ILASS-Korea
• /
• v.29 no.3
• /
• pp.105-111
• /
• 2024

Although the classic Kelvin-Helmholtz model of aerodynamically driven jet breakup(primary breakup) has been widely employed in engine CFD codes for the last three decades, the model is not generally predictive. This lack of predictive capability points to the likelihood of an incorrect physical basis for the model formulation. As such, there have been more recent spray-model development efforts that incorporate additional sources of jet instability and breakup, including nozzle-generated turbulence and cavitation but predictive capabilities have remained elusive. Meanwhile, it should be noted that modern combustors increasingly operate under low-temperature combustion(LTC) conditions, where ambient densities and aerodynamic forces are much lower than under classical operating conditions. Therefore, further consideration of physical model formulation is needed. The previous literature introduced a new primary atomization modeling approach premised on experimental measurements by the Faeth group, which demonstrate that breakup is governed by nozzle-generated turbulence under low ambient density conditions. In this new modeling approach, termed the KH-Faeth model, two different primary breakup models are combined to allow the hybrid breakup modeling approach, i.e. Kelvin- Helmholtz instability breakup mechanism and turbulence-induced breakup are competed via dominant breakup rate evaluation. In the current work, we implement this hybrid KH-Faeth model within the open-source CFD framework OpenFOAM and validate the model against detailed drop sizing measurements stemming from collaborative experiments between Georgia Tech and Argonne National Laboratory.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.2
• /
• pp.213-218
• /
• 2010

A cooling system utilizing liquid helium to chill the cryopanel (800 mm $\times$ 700 mm dimensions) down to 4.2 K was designed, implemented, and tested to verify the role of the cryopanel as a heat sink for the payload of a spacecraft inside the large thermal vacuum chamber (effective dimensions : 8 m ($\Phi$) $\times$ 10 m (L)) of KARI (Korea Aerospace Research Institute). Two LHe (Liquid Helium) Dewars, one for the main supply and the other for refilling, were used to supply liquid helium or cold helium gas into this cryopanel, and flow control for the target temperature of the cryopanel within requirements was done through fine adjustment of the pressure inside the LHe Dewars. The return helium gas from the cryopanel was reused as a thermal barrier to minimize the heat influx on the core liquid helium supply pipe. The test verified a cooling time of around three hours from the ambient temperature to 40 K (combined standard uncertainty of 194 mK), the capacity for maintaining the cryopanel at intermediate temperatures, and a 1 K uniformity over the entire cryopanel surface at around 40 K with 20 W cooling power.

• Journal of the Korean Solar Energy Society
• /
• v.37 no.1
• /
• pp.47-57
• /
• 2017

Solar energy is one of the important renewable energy resources. It can be used for air heating, hot water supply, heat source of desiccant cooling system and so on. And many researches for enhancing efficiency have been conducted because of these various uses of solar thermal energy. This study was performed to investigate the air heating performance of hybrid solar air-water heater that can heat air and liquid respectively or simultaneously and finding method for improving thermal performance of this collector. This collector has both liquid pipe and air channel different with the traditional solar water and air heater. Fins were installed in the air channel for enhancing the air heating performance of collector. Also air inlet & outlet temperature, ambient temperature and solar collector's inner part temperature were confirmed with different air velocity on similar solar irradiance. As a result, temperature of heated air was shown about $43^{\circ}C$ to $60^{\circ}C$ on the $30^{\circ}C$ of ambient temperature and thermal efficiency of solar collector was shown 28% to 73% with respect to air velocity. Also, possibility of improvement of thermal performance of this collector could be ascertained from the heat transfer coefficient calculated from this experiment. Thus, it is considered that the research for finding optimal structure of hybrid solar air-water heater for enhancing thermal performance might be needed to conduct as further study based on the method for improving air heating performance confirmed in this study.