• Geomechanics and Engineering
• /
• v.31 no.2
• /
• pp.167-181
• /
• 2022

Soil liquefaction has been one of the most important concerns in geotechnical earthquake engineering in recent years, due to its damages to structures and its destructive effects. The cyclic liquefaction of silty sands, in particular, remains of great interest for both research and application. Although many factors are known that affect the liquefaction resistance of sands, the effect of fine grain content is perhaps one of the most studied and still controversial. In this study, 48 deformation-controlled cyclic simple shear tests were performed on BS and CS silt samples mixed with 5%, 15% and 30% by weight of Krk085, Krk042 and Krk025 sands in constant-volume conditions to determine the liquefaction potential of silty sands. The tests were carried out at 30% and 50% relative density and under 100 kPa effective stress. The results revealed that the liquefaction potential of silty sand increases with increasing average particle size ratio (D_50sand / d_50silt) of the mixture for a fixed silt content. Furthermore, for identical base sand, the liquefaction potentials of coarse grained sands increase with increasing silt content, while the respective potentials of fine grained sands generally decrease. However, this situation may vary depending on the silt grain structure and is affected by the nature of the fine grains. In addition, the variation of the void ratio interval was shown to provide a good intuition in determining the liquefaction potentials of silty sands, while the intergranular void ratio alone does not constitute a criterion for determining the liquefaction potentials of silty sands.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2C
• /
• pp.83-94
• /
• 2008

In this study an effective stress analysis was performed to evaluate liquefaction potential and ground settlement for reclaimed sites. The effective stress model can simulate the stiffness degradation due to excess pore pressure and resulting ground deformation. It is applicable to a wide range of strain. An equivalent linear analysis suitable for low strain levels was also carried out to compare the effective stress analysis. Shear stress ratio calculated from an equivalent linear analysis was used to determine SPT blow count to prevent liquefaction. Depending on the magnitude of potential earthquake and fine contents, the SPT blow count was converted into an equivalent cone tip resistance. It was compared with the measured cone tip resistance. The measured elastic shear wave velocity and cone tip resistance from two reclaimed sites in Incheon were used to perform liquefaction analyses. Two liquefaction evaluation methods showed similar liquefaction potential which was evaluated continuously. The predicted excess pore pressure ratio of upper 20 m was between 40% and 70%. The calculated post-shaking settlement caused by excess pore pressure dissipation was less than 10 cm.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1528-1537
• /
• 2005

The purpose of this study is investigated the method for estimation of the liquefaction on the reclaimed land, located in Incheon and assessed the ability of liquefaction under the condition of criteria, which is the magnitude '6.5' of seismic on the basis of the domestic seismic characteristics. Performed not only field test but the experiment as well to study how the fine content would affect into the dreging and reclaimed land and also estimated the safety factor through the empirical method and anticipated detail method based on the results. Within the reclaimed land, there are many sized soils which are almost extended from well-graded silty sand(SM) to poor-graded fine grained sand, and which have the condition, so called, the liquefaction which is easily to bring into under the circumstances within the ground. However, partly, now that the soil is mixed with silt and silty clay which include the content of fine grained dust quite a bit, the difficulties and inconveniences has been expected while trying to find the ratio of cyclic resistance, but finally Seed and Idriss method showed the most way when we estimate the safety factor on the liquefaction.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.10
• /
• pp.57-71
• /
• 2020

Liquefaction-induced sand boils were observed during the Pohang earthquake (Moment magnitude, 5.4) on November 15, 2017, specifically in the region of agricultural fields and park areas near the epicenter. This was recorded as the first observed liquefaction phenomenon in Korea. This paper analyzes liquefaction potentials at the key sites at Pohang area. The simplified methods and current design standard were used to evaluate the occurrence of liquefaction. The seismic demand was estimated based on the NGA-WEST2 ground motion prediction equations (GMPEs). The liquefaction resistance of the ground was determined using the in-situ tests: standard penetration test (SPT) and cone penetration test (CPT). The liquefaction potentials were quantified by liquefaction potential index (LPI), which were compared with those from the previous studies.

• The Journal of Engineering Geology
• /
• v.33 no.1
• /
• pp.151-167
• /
• 2023

This study compares the revised method in loose saturated sandy ground where the LNG storage tank will be installed with an evaluation method by one-dimensional effective stress analysis using the UBC3D-PLM model. Various laboratory and field tests were conducted to establish the parameters necessary for evaluation. The revised liquefaction evaluation method using the seismic response analysis result and N value from standard penetration testing evaluated the possibility of liquefaction as high, but assessment using effective stress analysis, which can consider various liquefaction resistance factors, found the site to be somewhat stable against liquefaction. One-dimensional finite element analysis using UBC3D-PLM modeling facilitated easier assessment of stability against liquefaction than the other methods and minimized the area required for reinforcement against liquefaction. In addition, it is expected that two-and three-dimensional numerical analysis considering the foundation of the LNG storage tank can identify the seismic design and behavior when liquefaction occurs.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.3
• /
• pp.39-46
• /
• 2019

The liquefaction is a phenomenon that the effective stress becomes zero due to the rapidly accumulated excess pore water pressure when a strong load acts on the ground for a short period of time, such as an earthquake or pile driving, resulting in the loss of the shear strength of the ground. Since the Geongju and Pohang earthquake, liquefaction brought increasing domestic attention. This liquefaction can be assessed mainly through the semi-empirical procedures proposed by Seed and Idriss (1982) and the liquefaction risk based on the penetration resistance obtained from borehole DB and SPT. However, the geotechnical information data obtained by the in-situ tests or boring information fundamentally have an issue of the representative of the target area. Therefore, this study sought to construct a ground information database by classifying and reviewing the ground information required for liquefaction assessment, and tried to solve the representative problem of the soil layer that is subject to liquefaction evaluation by performing spatial interpolation using GIS.

• Journal of the Korean GEO-environmental Society
• /
• v.21 no.6
• /
• pp.5-11
• /
• 2020

Recently, due to the liquefaction caused by earthquakes in Pohang and surrounding areas, the importance of researches on the liquefaction assessment has increased. The possibility of liquefaction can be assessed using the geotechnical information. The cyclic resistance ratio (CRR) value used in the assessment of liquefaction can be determined by using the SPT-N values or shear wave velocity, V_s value. A study was conducted to compare the accuracy of the liquefaction assessment using these two types of geotechnical information, and concluded that the results using SPT-N values are more accurate than those using V_s values. The previous study speculated that the used V_s value was measured at a depth of 12 m uniformly without considering the critical depth of liquefaction. Therefore, 10 empirical equations that convert SPT-N values measured at critical depth of liquefaction into V_s values to confirm the validity of geotechnical information measured at 12 m points uniformly are used to assess the liquefaction possibility and the results were compared with the actual liquefaction results to confirm the accuracy. As a result, 7 out of 10 cases considering critical depth for liquefaction show higher accuracy than those not considered.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.2
• /
• pp.5-14
• /
• 2010

In this study, cyclic triaxial tests were performed under anisotropically consolidated condition by using irregular earthquake loading to consider in-situ condition and seismic wave. Jumunjin sand with a relative density 50 percent was used in the tests. The consolidation pressure ratio (K) was changed from 0.5 to 1.0. The Ofunato and Hachinohe wave were applied as irregular earthquake loadings and liquefaction resistance strengths of each specimen were estimated from the excess pore water pressure (EPWP) ratio. As a results of the cyclic triaxial tests, EPWP ratio increased with increased K value. It shows that isotropically consolidated sand is more susceptible to liquefaction than anisotropically consolidated sand under equal confining pressure and dynamic loadings. From the test results, the relationship between K and EPWP ratio normalized by effective confining pressure and deviator stress was proposed. And a new factor which corrects the liquefaction resistance strength for the in-situ stress condition is proposed.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.6
• /
• pp.49-59
• /
• 2016

We develop liquefaction resistance curves, which represent the correlation between cyclic resistance ratio (CRR) and number of cycles (N) to estimate the build-up of residual excess pore pressure from simple shear tests performed for this study and also from published literature. The liquefaction curve is calculated from two models. The comparisons show that one of the models is not reliable because it underestimates CRR. The scatter of the data is shown to be significantly reduced when CRR is normalized to the resistance ratio at N = 15 ($CRR_{N=15}$). Use of the normalization is particularly useful because CRR can be easily estimated from field tests. From normalization, we propose mean, upper, and lower curves. The corresponding design equation and its parameters are also proposed. We believe that the proposed curves can be used for effective stress site response analyses and evaluation of the seismic performance of port structures.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.4
• /
• pp.133-152
• /
• 1999

The cyclic triaxial test was carried out to research liquefaction characteristics and sample disturbance effects of silty sand soils at the west coast in Korea. First, liquefaction in silty sand was generated when axial strain approached to $\pm10%$ of strain and behavior of pore pressure was similar to the formula suggested by Seed, Martin, and Lysmer(1975). Also, it was found that dilatancy was generated at failure. Secondly, the liquefaction evaluation methods suggested by many researchers were carried out and the results were compared. In these methods the weak depth in liquefaction was similar and the method carried out by cyclic triaxial test on remolded sample showed the least safety factor. Thirdly the stress ratio by cyclic triaxial test was compared with that obtained from SPT N-value as a kind of empirical methods. It was found that the effect of sample disturbance was relatively small when SPT N-value was less than 20, but there were large differences in safety factor and resistance of liquefaction in soil by the effects of disturbance and remolding when SPT N-value was more than 20.