• Atmosphere
• /
• v.24 no.2
• /
• pp.197-206
• /
• 2014

The effects of different averaging operators and atmospheric stability on the turbulent fluxes are investigated using the vertical velocity, air temperature, carbon dioxide concentration, and absolute humidity data measured at 10 Hz by a 3-dimensional sonic anemometer and an open-path $CO_2/H_2O$ infrared gas analyzer installed at a height of 18.5 m on the rooftop of the Jungnang KT building located at a typical residential area in Seoul, Korea. For this purpose, 7 different averaging operators including block average, linear regression, and moving averages during 100 s, 300 s, 600 s, 900 s, and 1800 s are considered and the data quality control procedure such as physical limit check and spike removal is also applied. It is found that as the averaging interval becomes shorter, turbulent fluxes computed by the moving average become smaller and the ratios of turbulent fluxes computed by the 100 s moving average to the fluxes by the 1800 s moving average under unstable stability are smaller than those under neutral stability. The turbulent fluxes computed by the linear regression are 85~92% of those computed by the 1800 s moving average and nearly the same as those computed by 900 s moving average, implying that the adequate selection of an averaging operator and its interval will be very important to estimate more accurate turbulent fluxes at urban area.

• Journal of the Society of Naval Architects of Korea
• /
• v.61 no.1
• /
• pp.8-18
• /
• 2024

The present study concerns reduced order modeling of a marine diesel engine, which can be used for outlier detection in status monitoring and carbon intensity index calculation. Principal Component Analysis (PCA) is introduced for the reduced order modeling, focusing on the feasibility of detecting and treating nonlinear variables. By cross-correlation, it is found that there are seven non-linear data channels among 23 data channels, i.e., fuel mode, exhaust gas temperature after the turbocharger, and cylinder coolant temperatures. The dataset is handled so that the mean is located at the nominal continuous rating. Polynomial presentation of the dataset is also applied to reflect the linearity between the engine speed and other channels. The first principal mode shows strong effects of linearity of the most data channels to show the linearity of the system. The non-linear variables are effectively explained by other modes. second mode concerns the temperature of the cylinder cooling water, which shows small correlation with other variables. The third and fourth modes correlates the fuel mode and turbocharger exhaust gas temperature, which have inferior linearity to other channels. PCA is proven to be applicable to data given in binary type of fuel mode selection, as well as numerical type data.

• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.1
• /
• pp.66-73
• /
• 2005

Hydrogen linear power system is estimated as the next generation power system which can obtain a performance as same as fuel cell. In order to develop Hydrogen combustion power system with high thermal efficiency, it is very important to understand the basic characteristics of hydrogen combustion and establish combustion stabilization technique of its system. In this study, RICEM(Rapid Intake Compression Expansion Machine) for researching of hydrogen combustion linear power system was manufactured and evaluated, and the basic characteristics of linear RICEM were analyzed.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1048-1050
• /
• 2003

Recently, many linear motion generators and motors are rapidly finding applications that ranges from short stroke linear motion vibrators, such as dynamic con type loud speakers to stilting engine driven linear reciprocating alternators, compressors, textile machines etc. In this paper, we analyze the characteristics of tubular linear motor with Halbach and radial magnet array respectively. We already derived magnetic field solutions due to the PMs and to the currents and Motor thrust. On the basis of analytical field solutions, this paper deals with flux linkages and back emf. The results are validated extensively by comparison with finite element analyses. Then, this parer also presents thrust characteristics according to design parameters for each model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.9
• /
• pp.3119-3124
• /
• 2010

The purpose of this paper is to analyze dynamic behaviors of the oil film thickness and engine bearings in both aligned and misaligned operation conditions of a crankshaft using computer simulation techniques. A crankshaft as an elastic body is modeled for a misaligned crankshaft which is very important design parameter of the film thickness and engine bearings. In this analysis, a dynamic characteristic of a minimum oil film is analyzed based on the elastohydrodynamic lubrication theory. The boundary conditions for analyzing the film behaviors include non-linear constraint forces and bending moments in engine bearings. The more expedient model of an engine bearing is extended to consider the effect of crankshaft misalignment. The computed results indicate that the minimum oil film thickness that causes a major influence on the performance of engine bearings has showed a decrease of 16% to 24% for the misaligned crankshaft compared with an aligned crankshaft. The computed results show that the misalignment of a crankshaft inevitably brings the reduction of minimum oil film thickness and this may increase the failure of a bearing. These results as design parameters are very useful for a bearing designer as a firm reference data of an automotive engine.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.2
• /
• pp.38-46
• /
• 1998

A theoretical and an empirical application of the speed control of a single-shaft turbo-jet engine was done using an observer for Linear Quadratic Gausian(LQG) that is one of the robust control fields. Based on a general controller design with state feedback, a controller with output feedback was designed to find out a sufficient condition in finding an Asymptotic Stability After defining of the total system through the modeling of a real turbo-jet engine, a Tracking Control was carried out. Furthermore, a saturation of the control input was theoretically considered in the output feedback controller to simulate more similar real condition.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.576-580
• /
• 2004

In this paper, we present a design and implementation of a TV-Anytime compliant STB to provide personalized content consumption according to user preferences and various terminal/network conditions. This paper mainly details with a metadata engine which consists of meta data de-multiplexing, metadata decoding, and metadata-based content browsing. For personalized content consumption, the proposed metadata engine provides the following key functionalities: advanced EPG, non-linear segment navigation wirh Tables-of-Content and/or event-based summary, automatic recommendation of user-preferred programs, and etc. The implemented STB employing the metadata engine is successfully tested with a set of service scenarios in an end-to-end broadcasting test-bed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.1
• /
• pp.75-81
• /
• 2000

To provide the appropriate direction for development of transient control in a gasoline engine, transient performance analysis and evalution under four accelerating types based on typical driver's acceleration type were implemented by experimental study. In order to evaluate the characteristics of transient performance quanititatively, the concept and method by transient response specifications were introduced. Several performance parameters in terms of engine speed(RPM), manifold absolute pressure(MAP), fuel injection duration($\DeltatI_{nj}$) and air excess ratio($\lambda$) were emasured simultaneously during the four types of the throttle valve opening with the step motor controlled by PC. The result showed that transient response specifications in terms of delay time, rising time and settling time characterized the transient performance for four acceleration types quantitatively. Intensified acceleration type was most economical and linear acceleration type revealed the best emission performance.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.6
• /
• pp.1510-1519
• /
• 1994

It is important to understand the friction characteristics between piston-ring assembly and cylinder wall for the friction loss reduction as well as the solution of problem such as scuffing wear and oil consumption. A new system was developed for the piston-ring assembly friction force measurement. This system was applied to the friction force measurement to find its functional relationship with variables such as engine speed, oil viscosity, and engine load. The friction mean effective pressure(fmep) was found to have a linear relationship with$(\vpsilon{U})^{0.42}$ under motering and with$(\vpsilon{U})^{0.45}$ under firing operations, where $\vpsilon$ is the kinematic oil viscosity and U is mean piston speed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.609-615
• /
• 2001

In this paper, the eigenvalue sensitivity of vehicle powertrain was investigated by analytic method. The powertrain system was considered as a rigid body with multiple engine mounts, and the engine mounts were supposed as three linear springs in three orthogonal directions. The design parameters for the sensitivity analysis were engine mount properties (positions, stiffness, and orientations) and powertrain properties (mass, second moment of inertia, and center of gravity). Firstly, an effective form of eigenvalue problem for the powertrain system was introduced. Then, the analytic sensitivity of eigenvalue was derived using the equation. Lastly, the derived sensitivity equation was applied to a real powertrain system to provide its correctness and applicability.